Schedule 80 PVC Technical Information Schedule 80 PVC · PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (2024)

Schedule 80 PVC Technical Information Schedule 80 PVC · PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (1)

Schedule 80 PVC Technical InformationSchedule 80 PVC Pipe Dimensions & Pressure Ratings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 336Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Maximum PVC Service Temperature 140°FPressure De-rating at Elevated Temperatures

The pressure ratings given above are for water, non-shock, @ 73°F. The specifi ed derating factors for PVC are suitable for pipe conveying water at elevated temperatures. To determine elevatedtemperature rating, multiply 73°F [23°C] pressure rating by appropriate factor shown in the tablefor desired operating temperature. When working near maximum specifi ed temperature, solvent cement joints are recommended in place of threaded connections. Where disassembly is required at elevated temperatures use Spears® Special reinforced (SR) adapters, fl anges, unions or groovedcoupling connections. Spears® recommends that only Schedule 80 or heavier wall thickness pipe should be threaded.

See Plastic Pipe Engineering Guide for additional information

Schedule 80 Pipe Dimensions & Pressure Ratings

PVC PipeOperating Temp (°F) De-Rating Factor

73 1.00

80 0.88

90 0.75

100 0.62

110 0.51

120 0.40

130 0.31

140 0.22EX: 2" PVC SCHEDULE 80 @ 120°F = 400 psi x 0.40 = 160 psi max. @ 120°F.

Nom. Pipe Size (in) O.D. Average I.D. Min. Wall Nominal Wt./Ft. Maximum. W.P. PSI*

1/8 .405 .195 0.095 0.063 12301/4 .540 .282 0.119 0.105 11303/8 .675 .403 0.126 0.146 9201/2 .840 .526 0.147 0.213 8503/4 1.050 .722 0.154 0.289 6901 1.315 .936 0.179 0.424 630

1-1/4 1.660 1.255 0.191 0.586 5201-1/2 1.900 1.476 0.200 0.711 470

2 2.375 1.913 0.218 0.984 4002-1/2 2.875 2.290 0.276 1.500 420

3 3.500 2.864 0.300 2.010 3703-1/2 4.000 3.326 0.318 2.452 350

4 4.500 3.786 0.337 2.938 3205 5.563 4.768 0.375 4.078 2906 6.625 5.709 0.432 5.610 2808 8.625 7.565 0.500 8.522 250

10 10.750 9.493 0.593 12.635 23012 12.750 11.294 0.687 17.384 23014 14.000 12.410 0.750 20.852 22016 16.000 14.213 0.843 26.810 22018 18.000 16.014 0.937 33.544 22020 20.000 17.814 1.031 41.047 22024 24.000 21.418 1.218 58.233 210

Schedule 80 PVC Technical Information Schedule 80 PVC · PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (2)

Schedule 80 PVC Technical Information

Schedule 80 Product Overview

TECHNICAL INFORMATIONWEIGHTS & DIMENSIONS

Schedule 80 PVC Fittings

Contact Spears® for any information not found.

Page 337 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Schedule 80 PVC Technical Information Schedule 80 PVC · PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (3)

Schedule 80 PVC Technical Information

Schedule 80 Product Overview

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 338Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PVC Performance Engineered & Tested

SPEARS® Schedule 80 PVC product designs combine years

of proven experience with computer generated stress analysis

to yield the optimum physical structure and performance

for each fi tting. Material reinforcement is uniformly placed

in stress concentration areas for substantially improved

pressure handling capability. Resulting products are

subjected to numerous verifi cation tests to assure obtaining

the very best PVC fi ttings available.

1/4" Through 14" AvailabilitySpears® comprehensive line of PVC injection molded ttings and extruded pipe offers a variety of configurations in sizes 1/4" through 14". Schedule 80 ttings are manufactured to ASTM D 2467 and pipe is produced to ASTM D 1785. Spears® exclusive CL150 Flanges are produced in sizes 1/2" - 18" with ANSI B16.5 bolt patterns, plus numerous Unions, Saddles, Transition and Specialty ttings in a variety of sizes.

Exceptional Chemical & Corrosion ResistanceUnlike metal, PVC ttings and pipe never rust, scale, or pit, and will provide many years of maintenance-free service and extended system life.

High Temperature RatingsPVC thermoplastic can handle uids at service temperatures up to 140°F (60°C), allowing a wide range of process applications, including corrosive uids.

Lower Installation CostsSubstantially lower material costs than steel alloys or lined steel, combined with lighter weight and ease of installation, can reduce installation costs by as much as 60% over conventional metal systems.

Higher Flow CapacitySmooth interior walls result in lower pressure loss andhigher volume than conventional metal ttings.

Additional Fabricated Con gurations through 36"Extra large, hard-to-find, and custom configurationsare fabricated from NSF® Certified pipe. Fittings areengineered and tested to provide full pressure handlingcapabilities according to Spears® speci cations.

Advanced Design Specialty FittingsSpears® wide range of innovative, improved productsinclude numerous metal-to-plastic transition ttings and unions with Spears® patented special reinforced (SR)plastic threads.

PVC ValvesSPEARS® PVC Valve products are available for totalsystem compatibility and uniformity.

PVC Sample Engineering Speci cationsAll PVC Schedule 80 pipe and ttings shall be produced by Spears® Manufacturing Company from PVC Type I, cell classi cation 12454, conforming to ASTM Standard D 1784. All PVC injection molded Schedule 80 ttings and extruded pipe shall be Certi ed for potable water service by NSF International. All Schedule 80 ttings shall be manufactured in strict compliance to ASTM D 2467 and Schedule 80 pipe shall be manufactured in strict compliance to ASTM D 1785. All fabricated ttings shall be produced in accordance with Spears® General Speci cations for Fabricated Fittings. All PVC anges shall be designed and manufactured to meet CL150 bolt pattern per ANSI Standard B16.5 and rated for a maximum internal pressure of 150 psi, non-shock at 73°F.

Schedule 80 PVC Technical Information Schedule 80 PVC · PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (4)

Schedule 80 PVC Technical Information

Schedule 80 Product Overview

Page 339 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

General InformationRecommendations For Installers And Users

Plastic piping systems should be ENGINEERED, INSTALLED and OPERATED in accordance with ESTABLISHED DESIGN AND ENGINEERINGSTANDARDS AND PROCEDURES for plastic piping systems. Suitability for the intended service application should be determined by the installer and/or user prior to installation of a plastic piping system. PRIOR TO ASSEMBLY, all piping system components should be inspected for damage orirregularities. Mating components should be checked to assure that tolerances and engagements are compatible. Do not use any componentsthat appear irregular or do not fit properly. Contact the appropriate manufacturer of the component product in question to determine usability.Consult all applicable codes and regulations for compliance prior to installation.

Solvent Weld Connections — Use quality solvent cements and primers formulated for the intended service application, pipe size and type of joint. While the pipe and fitting materials may be compatible with the intended medium, the solvent cement may not be. Consult the manufacturers for suitability ofuse. Read and follow the cement and primer manufacturers’ applications and cure time instructions thoroughly. Be sure to use the correct size applicator.

Threaded Connections — Use a quality grade thread sealant. WARNING: SOME PIPE JOINT COMPOUNDS OR PTFE PASTES MAYCONTAIN SUBSTANCES THAT COULD CAUSE STRESS CRACKING TO PLASTIC. Spears® Manufacturing company recommends the useof Spears® BLUE 75™ Thread Sealant which has been tested for compatibility with Spears® products. Please follow the sealant manufacturers’ application/installation instructions. Choice of an appropriate thread sealant other than those listed above is at the discretion of the installer. 1 to2 turns beyond FINGER TIGHT is generally all that is required to make a sound plastic threaded connection. Unnecessary OVERTIGHTENINGwill cause DAMAGE TO BOTH PIPE AND FITTING.

Standards and SpecificationsMolded Schedule 80 PVC products are manufactured to ASTM D 2467 for use with pipe manufactured to ASTM D 1785. Certain products carry reduced pressure handling capability and have maximum internal pressure ratings at 73°F noted.

Fabricated Schedule 80 PVC pressure fittings (part numbers ending with “F”) are manufactured to Spears® specifications for use with pipe manufactured to ASTM D 1785. General Specifications for Standard Fabricated Fittings for additional information.

All specified Schedule 80 PVC products are manufactured from materials certified by NSF® for use in potable water service.

The information contained in this publication is based on current information and Product design at the time of publication and is subject tochange without notification. Our ongoing commitment to product improvement may result in some variation. No representations, guaranteesor warranties of any kind are made as to its accuracy, suitability for particular applications or results to be obtained therefrom. For verification of technical data or additional information not contained herein, please contact Spears® Technical Services Department [West Coast: (818) 364-1611 — East Coast: (678) 985-1263].

“Lead Free” low lead certification – unless otherwise specified, all Spears® Schedule 80 fittings specified here-in are certified by NSF Internationalto ANSI/NSF® Standard 61, Annex G and is in compliance with California’s Health & Safety Code Section 116825 (commonly known as AB1953)and Vermont Act 193. Weighted average lead content <=0.25%. Spears® PVC Pipe, Fittings and Valves have always been lead-free andCertified by NSF International for use in potable water systems. Spears® offers a wide range of lead-free specialty fittings and transition adapters for plumbing applications. However, certain brass threaded adapter fittings for applications that are not intended to convey water for human consumption through drinking or cooking are still produced and available.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (5)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 340Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

ASTM STANDARD DIMENSIONS

JIS K6741(mm)

DIN 8062(mm)

ASTM D1785(in.)

NPT—ANSI B1.20.1**Tapered Thread

BSP—BS21,DIN 2999,ISO 7/1 Thread

Nominal Actual* O.D. Actual* Nominal Actual* Designation Threads/in. Designation Threads/25.4mm16 22 15 20 1/2 .840 1/2 14 1/2 14

20 26 20 25 3/4 1.050 3/4 14 3/4 14

25 32 25 32 1 1.315 1 11.5 1 11

30 38 38 40 1-1/4 1.660 1-1/4 11.5 1-1/4 11

40 48 40 50 1-1/2 1.900 1-1/2 11.5 1-1/2 11

50 60 50 63 2 2.375 2 11.5 2 11

75 89 80 90 3 3.500 3 8 3 11

100 114 100 110 4 4.500 4 8 4 11

STANDARD COMPARISONSSPEARS® IPS-to-Metric transition unions are listed by nominal size. The chart below compares nominal and actual* pipe O.D. for each sizeaccording to the designated standard.

*Specified dimension, certain tolerances apply **NPT and BSP have different thread angles and not compatible.

SCHEDULE 80 PIPE DIMENSIONSASTM D 1785

NominalPipe

Size In.

MeanOutsideDiameter

In.

O. D.Tolerance

In.

MinimumWall

ThicknessIn.

1/8 0.405 ± 0.004 0.095

1/4 0.540 ± 0.004 0.119

3/8 0.675 ± 0.004 0.126

1/2 0.840 ± 0.004 0.147

3/4 1.050 ± 0.004 0.154

1 1.315 ± 0.005 0.179

1-1/4 1.660 ± 0.005 0.191

1-1/2 1.900 ± 0.006 0.200

2 2.375 ± 0.006 0.218

2-1/2 2.875 ± 0.007 0.276

3 3.500 ± 0.008 0.300

4 4.500 ± 0.009 0.337

5 5.563 ± 0.010 0.375

6 6.625 ± 0.011 0.432

8 8.625 ± 0.015 0.500

10 10.750 ± 0.015 0.593

12 12.750 ± 0.015 0.687

WALLTHICKNESS

I.D. O.D.

SCHEDULE 80 SOCKET DIMENSIONSASTM D 2467

NominalSize In.

Diameter SocketLength

MinimumC

EntranceA

BottomB

ToleranceA

1/8 0.417 0.401 ± 0.004 0.500

1/4 0.552 0.536 ± 0.004 0.625

3/8 0.687 0.671 ± 0.004 0.750

1/2 0.848 0.836 ± 0.004 0.875

3/4 1.058 1.046 ± 0.004 1.000

1 1.325 1.310 ± 0.005 1.125

1-1/4 1.670 1.655 ± 0.005 1.250

1-1/2 1.912 1.894 ± 0.006 1.375

2 2.387 2.369 ± 0.006 1.500

2-1/2 2.889 2.868 ± 0.007 1.750

3 3.516 3.492 ± 0.008 1.875

4 4.518 4.491 ± 0.009 2.250

5 5.583 5.553 ± 0.010 2.625

6 6.647 6.614 ± 0.011 3.000

8 8.655 8.610 ± 0.015 4.000

10 10.780 10.735 ± 0.015 5.000

12 12.780 12.735 ± 0.015 6.000

14 14.030 13.985 ± 0.015 7.000

A

C

B

AMERICAN NATIONAL STANDARD TAPER PIPE THREADS (NPT) ANSI

B1 .20.1 ASTM F 1498

NominalSize In.

ThreadsPerInch

EffectiveThreadLength

L

Pitch OfThread

P

1/8 27 0.2639 0.03704

1/4 18 0.4018 0.05556

3/8 18 0.4078 0.05556

1/2 14 0.5337 0.07143

3/4 14 0.5457 0.07143

1 11-1/2 0.6828 0.08696

1-1/4 11-1/2 0.7068 0.08696

1-1/2 11-1/2 0.7235 0.08696

2 11-1/2 0.7565 0.08696

2-1/2 8 1.1375 0.12500

3 8 1.2000 0.12500

4 8 1.3000 0.12500

5 8 1.4063 0.12500

6 8 1.5125 0.12500

8 8 1.7125 0.12500

L

P

90°30°30°

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (6)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 341 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TEE Socket x Socket x Socket

M

H1

HG

L

G1

Part Number Size G G1 H H1 L M Approx. Wt. (Lbs.)801-002 1/4 5/16 5/16 31/32 31/32 1-15/16 27/32 .04801-003 3/8 15/32 15/32 1-1/4 1-1/4 2-1/2 31/32 .06801-005 1/2 19/32 19/32 1-15/32 1-15/32 2-15/16 1-3/16 .11801-007 3/4 21/32 21/32 1-11/16 1-11/16 3-13/32 1-13/32 .16801-010 1 7/8 7/8 2 2 4 1-3/4 .27801-012 1-1/4 1-1/32 1-1/32 2-9/32 2-9/32 4-19/32 2-3/32 .39801-015 1-1/2 1-3/16 1-3/16 2-9/32 2-9/32 5-1/8 2-3/8 .52801-020 2 1-7/16 1-7/16 2-15/16 2-15/16 5-7/8 2-7/8 .80801-025 2-1/2 1-3/4 1-3/4 3-1/2 3-1/2 7-1/32 3-15/32 1.46801-030 3 2-1/16 2-1/16 3-31/32 3-31/32 7-15/16 4-5/32 2.16801-040 4 2-1/2 2-1/2 4-3/4 4-3/4 9-1/2 5-1/4 3.52

G = (LAYING LENGTH) intersection of center lines to bottom of socket/thread; 90° elbows, tees, crosses; ± 1/32 inch.

H = Intersection of center lines to face of fitting; 90° elbow tees, crosses; ± 1/32 inch.

J = Intersection of center lines to bottom of socket/thread; 45°elbows; ± 1/32 inch

Fabricated Dimension References: G = (LAYING LENGTH) intersection of center lines to bottom of

socket/thread; 90° elbows, tees, crosses ± 1/4 inch; 14" & larger ± 1/2 inch.

H = Intersection of center lines to face of fitting; 90° elbows ± 1/4 inch, 14" & larger ± 3/4 inch; wyes ± 1/2 inch; tees, crosses ± 1/4 inch; 14" & larger ± 1/2 inch.

J = Intersection of center lines to bottom of socket/thread; 45° elbows; ± 1/4 inch; 14" & larger ± 1/2 inch.

L = Overall length of fittings; ± 1/2 inch; 14" & larger ± 1 inch; wyes ± 1 inch.

M = Outside diameter of socket/thread hub; ± 1/4 inch.N = Socket bottom to socket bottom; couplings; ± 1/2W = Height of cap; ± 1/4 inch.

Typical Fabricated Dimension References

L = Overall length of fittings; ± 1/16 inch.H = Outside diameter of socket/thread hub; ± 1/16 inch.N = Socket bottom to socket bottom; couplings; ± 1/16 inchW = Height of cap; ± 1/16 inch.

Injection Molded Dimensions Referencesces:

M

H1

G1

L

H G

H1

G1

G

H

M

L

N

M

M

H

J

H1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (7)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 342Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TEE Socket x Socket x Socket

M

H1

HG

L

G1

Part Number Size G G1 H H1 L M Approx. Wt. (Lbs.)801-050 5 3-1/8 3-1/8 5-25/32 5-25/32 11-5/8 6-13/32 6.03

801-050F 5 5-1/2 5-1/2 8-1/2 8-1/2 17 6-5/16 13.26801-060 6 3-25/32 3-25/32 6-25/32 6-25/32 13-19/32 7-19/32 9.52801-080 8 4-13/16 4-13/16 8-7/8 8-7/8 17-3/4 9-23/32 21.21

801-080F 8 7-5/8 7-5/8 11-7/8 11-7/8 23-3/4 9-5/8 22.84801-100 10 5-3/4 5-3/4 10-13/16 10-13/16 21-5/8 11-19/32 37.89

801-100F 10 9 9 14-1/4 14-1/4 28-1/2 11-15/16 39.82801-120 12 6-15/16 6-15/16 12-15/16 12-15/16 25-7/8 14-1/4 54.45

801-120F 12 11-1/4 11-1/4 17-1/2 17-1/2 35 14-1/8 67.13801-140 14 7-1/32 7-1/32 14-7/32 14-1/32 28-7/16 15-21/32 63.61

801-140F 14 12-1/4 12-1/4 19-1/4 19-1/4 38-1/2 15-1/2 103.37801-160F 16 13 13 21 21 42 17-11/16 144.87801-180F 18 13-3/4 13-3/4 22-3/4 22-3/4 45-1/2 19-7/8 182.75801-200F 20 16-3/8 16-3/8 26-3/8 26-3/8 52-3/4 22-1/16 284.24801-240F 24 20-1/4 20-1/4 32-1/4 32-1/4 64-1/2 26-7/16 335.00

REDUCING TEESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)801-101 3/4x3/4x1/2 19/32 23/32 19/32 1-19/32 1-19/32 1-19/32 3-3/16 1-13/32 1-3/16 .14801-130 1x1x1/2 19/32 7/8 19/32 1-23/32 1-3/4 1-23/32 3-7/16 1-3/4 1-3/16 .20801-131 1x1x3/4 11/16 27/32 11/16 1-27/32 1-27/32 1-27/32 3-21/32 1-3/4 1-13/32 .23801-157 1-1/4x1x3/4 11/16 1-1/16 5/8 1-15/16 2-1/16 1-7/8 3-13/16 2-1/8 1-7/16 .30801-158 1-1/4x1x1 13/32 15/16 13/32 2-1/8 1-31/32 1-15/16 4 2-1/16 1-11/16 .33801-159 1-1/4x1x1-1/4 15/16 1-1/32 7/8 2-3/16 2-5/32 2-1/8 4-5/16 2-1/16 2-1/16 .39801-1661 1-1/4x1-1/4x1/2 7/8 1-13/32 7/8 2-3/32 2-3/8 2-3/32 4-7/32 2-1/8 1-3/4 .42801-167 1-1/4x1-1/4x3/4 5/8 31/32 5/8 1-15/16 1-31/32 1-15/16 3-7/8 2-1/8 1-13/32 .28801-168 1-1/4x1-1/4x1 27/32 1-1/32 27/32 2-3/32 2-5/32 2-3/32 4-7/32 2-3/32 1-3/4 .34

1 Outlet sized with bushing

M

H1

G H

L

G1

M1

H2 G2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (8)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 343 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING TEESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)801-202 1-1/2x1-1/4x1 7/8 1-7/32 7/8 2-1/4 2-11/32 2-1/4 4-1/2 2-7/16 1-13/16 .40801-209 1-1/2x1-1/2x1/2 9/16 1-1/16 9/16 1-31/32 1-15/16 1-31/32 3-15/16 2-3/8 1-3/16 .32801-210 1-1/2x1-1/2x3/4 11/16 1-1/32 11/16 2-1/16 2-1/32 2-1/16 4-5/32 2-11/32 1-13/32 .37801-211 1-1/2x1-1/2x1 27/32 1-5/32 27/32 2-15/32 2-5/16 2-15/32 4-15/16 2-11/32 1-3/4 .42801-212 1-1/2x1-1/2x1-1/4 1-3/16 1-3/16 1-3/16 2-9/16 2-7/16 2-9/16 5-1/8 2-3/8 2-1/8 .54801-247 2x2x1/2 9/16 1-13/32 9/16 2-3/32 2-9/32 2-3/32 4-3/16 2-7/8 1-5/32 .44801-248 2x2x3/4 11/16 1-13/32 11/16 2-3/16 2-13/32 2-3/16 4-3/8 2-27/32 1-13/32 .52801-249 2x2x1 27/32 1-7/16 27/32 2-3/8 2-9/16 2-3/8 4-3/4 2-7/8 1-3/4 .58801-250 2x2x1-1/4 31/32 1-11/32 31/32 2-17/32 2-19/32 2-17/32 5-3/32 2-7/8 2-1/8 .60801-251 2x2x1-1/2 1-5/32 1-13/32 1-5/32 2-11/16 2-13/16 2-11/16 5-3/8 2-15/16 2-15/32 .77801-2541 2x2x4 3-11/16 2-15/32 3-11/16 5-3/16 4-23/32 5-3/16 10-11/32 5-1/4 5-1/4 5.61801-287 2-1/2x2-1/2x1/2 19/32 1-19/32 19/32 2-3/8 2-15/32 2-3/8 4-23/32 3-1/2 1-3/16 .78801-288 2-1/2x2-1/2x3/4 21/32 1-1/2 21/32 2-7/16 2-17/32 2-7/16 4-27/32 3-17/32 1-13/32 .83801-289 2-1/2x2-1/2x1 27/32 1-23/32 27/32 2-5/8 2-27/32 2-5/8 5-1/4 3-17/32 1-23/32 .99801-290 2-1/2x2-1/2x1-1/4 1-1/32 1-3/4 1-1/32 2-27/32 3 2-27/32 5-11/16 3-9/16 2-3/32 1.11801-291 2-1/2x2-1/2x1-1/2 1-5/32 1-23/32 1-5/32 2-31/32 3-1/8 2-31/32 5-29/32 3-9/16 2-3/8 1.21801-292 2-1/2x2-1/2x2 1-13/32 1-5/8 1-13/32 3-3/16 3-1/8 3-3/16 6-3/8 3-1/2 2-7/8 1.32801-3331 3x3x1/2 1-7/16 2-7/8 1-7/16 3-5/16 3-3/4 3-5/16 6-5/8 4-3/16 2-7/8 1.94801-3341 3x3x3/4 1-7/16 2-11/16 1-7/16 3-5/16 3-11/16 3-5/16 6-5/8 4-3/16 2-7/8 1.92801-335 3x3x1 7/8 2 7/8 2-3/4 3-1/8 2-3/4 5-1/2 4-7/32 1-3/4 1.24801-3361 3x3x1-1/4 1-5/8 1-15/16 1-5/8 3-5/16 3-5/8 3-5/16 6-5/8 4-3/16 2-7/8 1.89801-337 3x3x1-1/2 1-5/32 2-1/16 1-5/32 3-1/16 3-7/16 3-1/16 6-1/8 4-3/16 2-3/8 1.44801-338 3x3x2 1-7/16 1-13/16 1-7/16 3-5/16 3-5/16 3-5/16 6-5/8 4-7/32 2-7/8 1.65801-339 3x3x2-1/2 1-3/4 1-31/32 1-3/4 3-5/8 3-11/16 3-5/8 7-1/4 4-3/16 3-17/32 1.88801-4151 4x4x1/2 1-7/16 3-17/32 1-7/16 3-11/16 4-13/32 3-11/16 7-11/32 5-1/4 2-7/8 2.62801-4171 4x4x1 1-15/32 3-9/32 1-15/32 3-11/16 4-3/8 3-11/16 7-3/8 5-7/32 2-7/8 2.55801-4181 4x4x1-1/4 1-1/8 2-31/32 1-1/8 3-13/32 4-7/32 3-13/32 6-25/32 5-1/4 2-3/8 2.18801-419 4x4x1-1/2 1-1/8 2-9/16 1-1/8 3-3/8 3-15/16 3-3/8 6-3/4 5-1/4 2-3/8 2.09801-420 4x4x2 1-7/16 2-1/2 1-7/16 3-11/16 4 3-11/16 7-3/8 5-1/4 2-7/8 2.35801-4211 4x4x2-1/2 2-1/16 2-11/16 2-1/16 4-5/16 4-3/4 4-5/16 8-5/8 5-1/4 4-1/8 3.48801-422 4x4x3 2-1/8 2-23/32 2-1/8 4-3/8 4-19/32 4-3/8 8-25/32 5-1/4 4-3/16 3.11

801-482F 5x5x1-1/4 4 4-11/16 4 7 6-3/16 7 14 6-5/16 2-1/16 5.99801-4841 5x5x1-1/2 3-5/32 5-17/32 3-5/32 5-13/16 6-29/32 5-13/16 11-5/8 6-13/32 6-13/32 8.86801-484F 5x5x1-1/2 4-1/8 5 4-1/8 7-1/8 6-1/2 7-1/8 14-1/4 6-5/16 2-5/16 9.10801-4861 5x5x2 3-5/32 5-3/32 3-5/32 5-13/16 6-19/32 5-13/16 11-19/32 6-13/32 6-13/32 8.39801-486F 5x5x2 4-5/16 4-3/4 4-5/16 7-5/16 6-1/2 7-5/16 14-5/8 6-5/16 2-13/16 6.87801-4871 5x5x2-1/2 3-5/32 4-23/32 3-5/32 5-13/16 6-15/32 5-13/16 11-5/8 6-13/32 6-13/32 8.28801-4881 5x5x3 3-5/32 4-5/8 3-5/32 5-13/16 6-1/2 5-13/16 11-19/32 6-13/32 6-13/32 8.21801-4901 5x5x4 3-5/32 3-29/32 3-5/32 5-13/16 6-5/32 5-13/16 11-5/8 6-13/32 6-13/32 7.40

1 Outlet sized with bushing

M

H1

G H

L

G1

M1

H2 G2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (9)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 344Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING TEESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)801-5231 6x6x1/2 1-7/16 4-13/16 1-7/16 4-7/16 5-11/16 4-7/16 8-7/8 7-19/32 2-7/8 .54801-5241 6x6x3/4 1 4 1 3-7/8 5 3-7/8 7-3/4 7-9/16 1-3/4 4.39801-525 6x6x1 27/32 3-23/32 27/32 3-7/8 4-27/32 3-7/8 7-3/4 7-9/16 1-3/4 4.34801-5261 6x6x1-1/4 1-7/16 4-3/16 1-7/16 4-7/16 5-15/32 4-7/16 8-7/8 7-19/32 2-7/8 5.23801-5271 6x6x1-1/2 1-7/16 4-3/32 1-7/16 4-7/16 5-1/2 4-7/16 8-7/8 7-19/32 2-7/8 5.25801-528 6x6x2 1-7/16 3-23/32 1-7/16 4-7/16 5-1/4 4-7/16 8-7/8 7-19/32 2-7/8 5.11801-5291 6x6x2-1/2 2-1/16 3-13/16 2-1/16 5-1/16 5-7/8 5-1/16 10-1/8 7-9/16 4-1/4 6.80801-530 6x6x3 2-1/16 3-3/4 2-1/16 5-3/32 5-5/8 5-3/32 10-3/16 7-19/32 4-1/4 6.48

801-530F 6x6x3 4-3/4 5-3/4 4-3/4 8 8 8 16 7-1/2 4-1/8 12.33801-532 6x6x4 2-11/16 3-23/32 2-11/16 5-11/16 5-31/32 5-11/16 11-13/32 7-19/32 5-1/4 7.69

801-533F 6x6x5 5-3/4 6-1/2 5-3/4 9 9-1/2 9 18 7-1/2 6-5/16 10.35801-5751 8x8x1 4-1/16 7-27/32 4-1/16 7-29/32 8-31/32 7-29/32 15-27/32 9-3/4 7-9/16 18.95801-5781 8x8x2 3-13/16 6-5/8 3-13/16 7-13/16 8-1/8 7-13/16 15-5/8 9-11/16 7-9/16 17.56801-578F 8x8x2 4-11/16 6-1/8 4-11/16 8-15/16 7-7/8 8-15/16 17-7/8 9-5/8 2-13/16 12.89801-579F 8x8x2-1/2 4-7/8 6-15/16 4-7/8 9-1/8 8-5/16 9-1/8 18-1/4 9-5/8 3-7/16 17.97801-5801 8x8x3 3-23/32 6-1/2 3-23/32 7-3/4 8-3/8 7-3/4 15-1/2 9-11/16 7-1/2 17.03801-580F 8x8x3 5-3/16 6-11/16 5-3/16 9-7/16 8-15/16 9-7/16 18-7/8 9-5/8 4-1/8 17.42801-582 8x8x4 2-5/8 4-27/32 2-5/8 6-5/8 7-3/32 6-5/8 13-1/4 9-3/4 5-9/32 11.56

801-582F 8x8x4 5-3/4 7-11/16 5-3/4 10 9-15/16 10 20 9-5/8 5-3/16 15.77801-585 8x8x6 3-27/32 4-13/16 3-27/32 7-29/32 7-27/32 7-29/32 15-27/32 9-23/32 7-9/16 15.52

801-621F 10x10x2 4-3/8 7-1/8 4-3/8 9-5/8 8-7/8 9-5/8 19-1/4 11-15/16 2-1316 21.56801-622F 10x10x2-1/2 5-1/4 7-5/16 5-1/4 10-1/2 9-5/16 10-1/2 21 11-15/16 3-7/16 20.44801-6231 10x10x3 3-25/32 7-17/32 3-25/32 9-3/8 9-3/8 9-3/8 18-25/32 12-1/16 7-9/16 26.67801-623F 10x10x3 4-7/8 7-11/16 4-7/8 10-1/8 9-15/16 10-1/8 20-1/4 11-15/16 4-1/8 20.67801-624 10x10x4 3-7/8 7-3/16 3-7/8 9-3/8 9-1/2 9-3/8 18-3/4 12-1/16 7-9/16 26.36

801-624F 10x10x4 5-3/8 8-11/16 5-3/8 10-5/8 10-15/16 10-5/8 21-1/4 11-15/16 5-3/16 23.04801-626 10x10x6 3-7/8 5-27/32 3-7/8 9-3/8 8-27/32 9-3/8 18-3/4 12-1/16 7-9/16 23.50

801-626F 10x10x6 5-7/8 9-1/16 5-7/8 11-1/8 12-5/16 11-1/8 22-1/4 11-15/16 7-1/2 34.74801-6281 10x10x8 5-15/16 7-3/4 5-15/16 11-7/16 11-3/4 11-7/16 22-7/8 12-1/16 12-1/16 43.06801-628F 10x10x8 8-1/4 9-15/16 8-1/4 13-1/2 14-3/16 13-1/2 27 11-15/16 9-5/8 34.59801-661F 12x12x2 4-3/4 8 4-3/4 11 9-3/4 11 22 14-1/8 2-13/16 29.04801-662F 12x12x2-1/2 5-7/16 8-3/16 5-7/16 11-11/16 10-3/16 11-11/16 23-3/8 14-1/8 3-7/16 37.84801-663F 12x12x3 5-1/4 8-9/16 5-1/4 11-1/2 10-13/16 11-1/2 23 14-1/8 4-1/8 32.26801-6641 12x12x4 4-11/32 10-1/8 4-11/32 10-15/16 12-3/8 10-15/16 21-7/8 14-1/4 9-23/32 32.86801-664F 12x12x4 5-3/4 9-9/16 5-3/4 12 11-13/16 12 24 14-1/8 5-3/16 32.86801-665F 12x12x5 7-1/8 9-5/16 7-1/8 13-3/8 12-5/16 13-3/8 26-3/4 14-1/8 6-5/16 47.29801-666F 12x12x6 7-1/4 9-15/16 7-1/4 13-1/4 13-3/16 13-1/4 26-1/2 14-1/8 7-1/2 45.37801-668 12x12x8 4-27/32 7-1/2 4-27/32 11-13/32 11-1/8 11-13/32 22-13/16 14-1/4 9-23/32 40.00

801-668F 12x12x8 8 10-13/16 8 14-1/4 15-1/16 14-1/4 28-1/2 14-1/8 9-5/8 57.91801-670F 12x12x10 10-1/4 10-13/16 10-1/4 16-1/2 16-1/16 16-1/2 33 14-1/8 11-15/16 67.18801-691F 14x14x2 5-3/16 8-9/16 5-3/16 12-3/16 10-5/16 12-3/16 24-3/8 15-1/2 2-13/16 38.66

1 Outlet sized with bushing

M

H1

G H

L

G1

M1

H2 G2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (10)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 345 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING TEESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)801-692F 14x14x2-1/2 5-7/16 8-3/4 5-7/16 12-7/16 10-3/4 12-7/16 24-7/8 15-1/2 3-7/16 44.34801-693F 14x14x3 5-3/4 9-1/8 5-3/4 12-3/4 11-3/8 12-3/4 25-1/2 15-1/2 4-1/8 40.35801-694F 14x14x4 6-1/2 10-1/8 6-1/2 13-1/2 12-3/8 13-1/2 27 15-1/2 5-3/16 41.85801-696F 14x14x6 8-1/4 10-1/2 8-1/4 15-1/4 13-3/4 15-1/4 30-1/2 15-1/2 7-1/2 63.15801-698F 14x14x8 9-1/4 11-3/8 9-1/4 16-1/4 15-5/8 16-1/4 32-1/2 15-1/2 9-5/8 74.74801-700F 14x14x10 10-1/8 11-3/8 10-1/8 17-1/8 16-5/8 17-1/8 34-1/4 15-1/2 11-15/16 79.05801-702 14x14x12 7-1/32 7-13/32 7-1/32 14-1/32 13-13/32 14-1/32 28-1/16 15-21/32 14-11/32 61.20

801-702F 14x14x12 11 11-3/8 11 18 17-5/8 18 36 15-1/2 14-1/8 93.81801-751F 16x16x2 5-7/8 9-1/2 5-7/8 13-7/8 11-1/4 13-7/8 27-3/4 17-11/16 2-13/16 62.38801-752F 16x16x2-1/2 6 9-11/16 6 14 11-11/16 14 28 17-11/16 3-7/16 55.65801-753F 16x16x3 6-5/16 10-1/16 6-5/16 14-5/16 12-5/16 14-5/16 28-5/8 17-11/16 4-1/8 56.70801-754F 16x16x4 6-1/8 11-1/16 6-1/8 14-1/8 13-5/16 14-1/8 28-1/4 17-11/16 5-3/16 60.66801-756F 16x16x6 8-5/8 11-7/16 8-5/8 16-5/8 14-11/16 16-5/8 33-1/4 17-11/16 7-1/2 85.07801-758F 16x16x8 9-5/8 12-5/16 9-5/8 17-5/8 16-9/16 17-5/8 35-1/4 17-11/16 9-5/8 94.91801-760F 16x16x10 10-5/8 12-5/16 10-5/8 18-5/8 17-9/16 18-5/8 37-1/4 17-11/16 11-15/16 103.85801-762F 16x16x12 11-5/8 12-5/16 11-5/8 19-5/8 18-9/16 19-5/8 39-1/4 17-11/16 14-1/8 116.70801-764F 16x16x14 12-3/4 12-11/16 12-3/4 20-3/4 19-11/16 20-3/4 41-1/2 17-11/16 15-1/2 129.51801-784F 18x18x4 6-7/8 11-15/16 6-7/8 15-7/8 14-3/16 15-7/8 31-3/4 19-7/8 5-3/16 91.52801-786F 18x18x6 8-1/2 12-5/16 8-1/2 17-1/2 15-9/16 17-1/2 35 19-7/8 7-1/2 115.09801-788F 18x18x8 9-1/2 13-3/16 9-1/2 18-1/2 17-7/16 18-1/2 37 19-7/8 9-5/8 118.85801-790F 18x18x10 10-1/2 13-3/16 10-1/2 19-1/2 18-7/16 19-1/2 39 19-7/8 11-15/16 128.48801-792F 18x18x12 11-1/2 13-3/16 11-1/2 20-1/2 19-7/16 20-1/2 41 19-7/8 14-1/8 151.17801-794F 18x18x14 12-3/4 13-9/16 12-3/4 21-3/4 20-9/16 21-3/4 43-1/2 19-11/16 15-1/2 151.23801-796F 18x18x16 13-1/2 14-3/16 13-1/2 22-1/2 22-3/16 22-1/2 45 19-11/16 17-11/16 140.86801-814F 20x20x4 7-11/16 12-7/8 7-11/16 17-11/16 15-1/8 17-11/16 35-3/8 22-1/16 5-3/16 114.37801-816F 20x20x6 8-7/8 13-1/4 8-7/8 18-7/8 16-1/2 18-7/8 37-3/4 22-1/16 7-1/2 130.08801-818F 20x20x8 9-7/8 14-1/8 9-7/8 19-7/8 18-3/8 19-7/8 39-3/4 22-1/16 9-5/8 137.63801-820F 20x20x10 10-7/8 14-1/8 10-7/8 20-7/8 19-3/8 20-7/8 41-3/4 22-1/16 11-15/16 123.96801-822F 20x20x12 11-7/8 14-1/8 11-7/8 21-7/8 20-3/8 21-7/8 43-3/4 22-1/16 14-1/8 164.33801-824F 20x20x14 12-7/8 14-1/2 12-7/8 22-7/8 21-1/2 22-7/8 45-3/4 22-1/16 15-1/2 176.28801-826F 20x20x16 14 15-1/8 14 24 23-1/8 24 48 22-1/16 17-11/16 191.64801-828F 20x20x18 15 15 15 25 24 25 50 22-1/16 19-7/8 215.72801-904F 24x24x4 9 14-11/16 9 21 16-15/16 21 42 26-7/16 5-3/16 191.09801-906F 24x24x6 9-1/4 15-1/16 9-1/4 21-1/4 18-5/16 21-1/4 42-1/2 26-7/16 7-1/2 207.79801-908F 24x24x8 10-1/4 15-15/16 10-1/4 22-1/4 20-3/16 22-1/4 44-1/2 26-7/16 9-5/8 215.05801-910F 24x24x10 11-1/4 15-15/16 11-1/4 23-1/4 21-3/16 23-1/4 46-1/2 26-7/16 11-15/16 248.46801-912F 24x24x12 12-1/4 15-15/16 12-1/4 24-1/4 22-3/16 24-1/4 48-1/2 26-7/16 14-1/8 290.75801-914F 24x24x14 13-1/4 16-5/16 13-1/4 25-1/4 23-5/16 25-1/4 50-1/2 26-1/16 15-1/2 279.60801-916F 24x24x16 14-3/4 16-15/16 14-3/4 26-3/4 24-15/16 26-3/4 53-1/2 26-7/16 17-11/16 297.80801-918F 24x24x18 15-3/4 16-13/16 15-3/4 27-3/4 25-13/16 27-3/4 55-1/2 26-7/16 19-7/8 303.81801-920F 24x24x20 16-3/4 18-3/16 16-3/4 28-3/4 28-3/16 28-3/4 57-1/2 26-7/16 22-1/16 341.61

M

H1

G H

L

G1

M1

H2 G2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (11)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 346Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TEESocket x Socket x Fipt

M

H1

HG

L

G1

Part Number Size G G1 H H1 L M Approx. Wt. (Lbs.)802-002 1/4 5/16 3/8 15/16 15/16 1-29/32 7/8 .05802-005 1/2 19/32 21/32 1-15/32 1-11/32 2-15/16 1-3/16 .14802-007 3/4 5/8 5/8 1-19/32 1-13/32 3-3/16 1-13/32 .14802-010 1 11/16 3/4 1-13/16 1-5/8 3-13/16 1-13/16 .23802-012 1-1/4 13/16 1-1/16 2-3/32 1-15/16 4-5/32 2-3/32 .34802-015 1-1/2 29/32 1-1/4 2-11/32 2-5/32 4-11/16 2-3/8 .49802-020 2 1-9/32 1-15/32 2-13/16 2-13/32 5-21/32 2-7/8 .77802-030 3 1-31/32 2-1/8 3-3/4 3-17/32 7-15/32 4-5/16 2.31802-040 4 2-11/32 2-21/32 4-5/8 4-5/32 9-7/32 5-9/32 3.37

802-060F 6 3-3/4 8-5/8 6-3/4 10-1/8 13-11/2 7-5/8 14.19802-080F 8 4-13/16 10-13/16 8-13/16 12-9/16 17-11/16 9-11/16 25.92

REDUCING TEESocket x Socket x Fipt

M

H1

GH

L

G1

M1

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)802-101 3/4x3/4x1/2 19/32 25/32 1-19/32 1-7/16 3-7/32 1-13/32 1-3/16 .14802-130 1x1x1/2 7/16 29/32 1-9/16 1-5/8 3-1/8 1-23/32 1-7/16 .18802-131 1x1x3/4 21/32 13/16 1-13/16 1-17/32 3-5/8 1-23/32 1-3/8 .21802-166 1-1/4x1-1/4x1/2 7/16 1-1/8 1-11/16 1-27/32 3-3/8 2-3/32 1-3/16 .26802-1671 1-1/4x1-1/4x3/4 7/8 1-23/32 2-1/8 2-7/16 4-7/32 2-3/32 1-3/4 .40802-168 1-1/4x1-1/4x1 27/32 1-1/32 2-3/32 1-29/32 4-7/32 2-3/32 1-11/16 .33802-2091 1-1/2x1-1/2x1/2 11/16 1-9/16 2-3/32 2-9/32 4-5/32 2-11/32 1-13/32 .40802-2101 1-1/2x1-1/2x3/4 7/8 1-27/32 2-1/4 2-19/32 4-1/2 2-3/8 1-11/16 .51802-211 1-1/2x1-1/2x1 27/32 1-9/32 2-1/4 2-3/32 4-15/32 2-3/8 1-11/16 .41802-212 1-1/2x1-1/2x1-1/4 1-1/32 1-5/32 2-7/16 2-3/32 4-27/32 2-3/8 2-1/16 .47802-2471 2x2x1/2 1/2 1-1/2 2 2-7/32 4 2-7/8 1-3/16 .45802-248 2x2x3/4 5/8 1-3/8 2-1/8 2-3/32 4-1/4 2-7/8 1-3/8 .47

1 Outlet sized with bushing

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (12)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 347 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING TEESocket x Socket x Fipt

M

H1

GH

L

G1

M1

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)802-249 2x2x1 27/32 1-1/2 2-11/32 3-11/32 4-11/16 2-7/8 1-11/16 .54802-2501 2x2x1-1/4 1-3/16 2-1/16 2-11/16 3 5-3/8 2-7/8 2-13/32 .86802-2511 2x2x1-1/2 1-7/16 2-5/16 2-15/16 3-11/32 5-7/8 2-7/8 2-7/8 1.20802-287 2-1/2x2-1/2x1/2 9/16 1-25/32 2-5/16 2-15/32 4-19/32 3-1/2 1-3/16 .76802-2881 2-1/2x2-1/2x3/4 27/32 2-11/32 2-21/32 3-5/32 5-9/32 3-9/16 1-13/16 1.06802-2891 2-1/2x2-1/2x1 1-3/32 2-11/32 2-27/32 3-1/4 5-11/16 3-1/2 2-1/8 1.19802-2901 2-1/2x2-1/2x1-1/4 1-3/16 2-15/32 2-31/32 3-15/32 5-15/16 3-1/2 2-3/8 1.30802-2911 2-1/2x2-1/2x1-1/2 1-7/16 2-1/2 3-3/16 3-1/2 6-3/8 3-1/2 2-7/8 1.51802-2921 2-1/2x2-1/2x2 1-3/4 3-15/16 3-1/2 2-7/8 7 3-15/32 3-15/32 1.86802-3331 3x3x1/2 7/8 2-11/16 2-3/4 3-7/16 5-1/2 4-1/8 1-23/32 1.27802-3341 3x3x3/4 7/8 2-19/32 2-3/4 3-11/32 5-1/2 4-3/16 1-3/4 1.26802-3351 3x3x1 1-3/16 2-31/32 3-1/16 3-7/8 6-1/8 4-1/8 2-11/32 1.53802-3371 3x3x1-1/2 1-7/16 2-23/32 3-5/16 3-23/32 6-5/8 4-1/4 2-29/32 1.84802-3381 3x3x2 2-3/32 3-11/32 3-31/32 4-3/8 7-15/16 4-5/32 4-5/32 3.03802-3391 3x3x2-1/2 2-3/32 2-3/4 3-31/32 4-5/16 7-15/16 4-1/8 4-1/8 2.90802-4151 4x4x1/2 1-7/16 3-5/8 3-11/16 4-3/8 7-3/8 5-1/4 2-7/8 2.61802-4161 4x4x3/4 1-15/32 3-27/32 3-23/32 4-17/32 7-7/16 5-1/4 2-7/8 2.72802-4171 4x4x1 1-7/16 3-17/32 3-23/32 4-13/32 7-13/32 5-1/4 2-7/8 2.73802-4191 4x4x1-1/2 3-11/16 3-1/2 3-11/16 3-31/32 7-3/8 5-1/4 2-7/8 2.63802-4201 4x4x2 2-1/8 4-1/32 4-3/8 5-1/32 8-25/32 5-1/4 4-3/16 3.77802-4211 4x4x2-1/2 2-1/8 3-15/32 4-3/8 5 8-25/32 5-1/4 4-3/16 3.62802-4221 4x4x3 2-5/8 3-5/8 4-7/8 5-1/4 9-3/4 5-1/4 5-1/4 5.13802-5251 6x6x1 2-1/16 5-3/16 5-3/32 6-1/16 10-5/32 7-19/32 4-1/4 7.11802-528F 6x6x2 4-5/8 5-1/8 7-7/8 6-9/16 15-3/4 7-1/2 3 11.01802-5291 6x6x2-1/2 2-1/16 4-21/32 5-3/32 6-3/16 10-5/32 7-19/32 4-1/4 6.97802-5301 6x6x3 2-11/16 4-3/4 5-9/16 6-3/8 11-1/8 7-1/2 5-1/4 13.79802-532F 6x6x4 5-1/4 6-3/4 8-1/2 8-1/4 17 7-1/2 5-3/16 13.77802-578F 8x8x2 4-11/16 6-1/16 8-15/16 7-1/2 17-7/8 9-5/8 3 15.46802-580F 8x8x3 5-3/16 7 9-7/16 8-7/16 18-7/8 9-5/8 4-1/8 18.24802-582F 8x8x4 5-3/4 7-11/16 10 9-1/8 20 9-5/8 5-3/16 17.71802-621F 10x10x2 4-3/8 7-9/16 9-5/8 8-15/16 19-1/4 11-15/16 3 26.78802-623F 10x10x3 4-7/8 8-3/16 10-1/8 9-5/8 20-1/4 11-15/16 4-1/8 31.67802-624F 10x10x4 5-3/8 8-13/16 10-5/8 10-5/16 21-1/4 11-15/16 5-3/16 32.18802-661F 12x12x2 4-3/4 8-7/16 11 9-13/16 22 14-1/8 3 37.80802-663F 12x12x3 5-1/4 9-1/4 11-1/2 10-11/16 23 14-1/8 4-1/8 36.19802-664F 12x12x4 5-3/4 9-15/16 12 11-7/16 24 14-1/8 5-3/16 47.80

1 Outlet sized with bushing

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (13)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 348Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TEESocket x Socket x Brass Fipt

M

GH

L

G1

H1

M1

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)802-005BR 1/2 7/8 31/32 1-7/16 1-17/32 2-5/8 1-5/32 1-7/32 .16

802-007BR 3/4 17/32 1-5/32 1-17/32 1-13/16 3-1/16 1-13/32 1-3/8 .23Not intended to convey or dispense water for human consumption through drinking or cooking

REDUCING TEESocket x Fipt x Socket

M

M1

M2

G1

G G2H

LH2

H1

Part Number Size G G1 G2 H H1 H2 L M M1 M2 Approx. Wt. (Lbs.)803-095 3/4x1/2x3/4 11/16 11/16 11/16 1-11/16 1-11/16 1-3/8 3-3/32 1-13/32 1-13/32 1-3/16 .15

SPECIAL REINFORCED REDUCING TEESocket x SR Fipt x Socket

M

M1

M2

G1

G G2H

LH2

H1

Part Number Size G G1 G2 H H1 H2 L M M1 M2 Approx. Wt. (Lbs.)803-095SR 3/4x1/2x3/4 11/16 11/16 11/16 1-11/16 1-11/16 1-13/32 3-1/8 1-13/32 1-13/32 1-7/32 .15

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (14)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 349 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING TEESocket x Socket x Brass Fipt

M1

G H

L

M G1

H1

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)

802-072BR 1/2x1/2x1/4 7/16 7/8 1-5/16 1-17/32 2-5/8 1-3/16 1-3/16 .22

802-101BR 3/4x3/4x1/2 7/16 1-1/32 1-7/16 1-5/8 2-29/32 1-13/32 1-3/16 .19

Not intended to convey or dispense water for human consumption through drinking or cooking

SPECIAL REINFORCED TEESocket x Socket x SR Fipt

M

H1

H G

L

G1

M1

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)

802-005SR 1/2 5/8 5/8 1-15/32 1-3/8 2-15/16 1-7/32 1-13/32 .13

802-007SR 3/4 19/32 11/16 1-19/32 1-13/32 3-3/16 1-13/32 1-13/32 .15

802-010SR 1 21/32 11/16 1-13/16 1-5/8 3-5/8 1-23/32 1-11/16 .25

802-012SR 1-1/4 13/16 1-1/16 2-3/32 1-15/16 4-3/16 2-3/32 2-1/16 .37

802-015SR 1-1/2 15/16 1-7/32 2-11/32 2-5/32 4-11/16 2-11/32 2-7/16 .51

802-020SR 2 1-5/16 1-1/2 2-13/16 2-13/32 5-21/32 2-7/8 3-1/32 .80

802-030SR 3 1-27/32 2-3/32 3-23/32 3-17/32 7-7/16 4-9/32 4-9/32 2.33

802-040SR 4 2-11/32 2-21/32 4-5/8 4-5/32 9-7/32 5-1/4 5-1/4 3.40

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (15)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 350Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED REDUCING TEESocket x Socket x SR Fipt

Part Number Size G G1 H H1 L M M1 Approx. Wt. (Lbs.)802-072SR 1/2x1/2x1/4 7/16 11/16 1-5/16 1-7/32 2-5/8 1-5/32 27/32 .09802-098SR 3/4x3/4x1/4 7/ 13/16 1-7/16 1-5/16 2-7/8 1-3/8 27/32 .12802-101SR 3/4x3/4x1/2 19/32 25/32 1-19/32 1-7/16 3-7/32 1-13/32 1-3/16 .15802-128SR1 1x1x1/4 7/8 2-5/8 2 2-11/16 4 2-3/32 27/32 .43802-130SR 1x1x1/2 7/16 29/32 1-9/16 1-5/8 3-1/8 1-23/32 1-3/16 .19802-131SR 1x1x3/4 21/32 7/8 1-13/16 1-19/32 3-19/32 1-23/32 1-3/8 .22802-164SR1 1-1/4x1-1/4x1/4 27/32 2-13/16 2-1/8 3-13/32 4-7/32 2-3/32 27/32 .43802-166SR 1-1/4x1-1/4x1/2 7/16 1-1/8 1-11/16 1-27/32 3-13/32 2-3/32 1-3/16 .26802-168SR 1-1/4x1-1/4x1 27/32 1-1/32 2-3/32 1-29/32 4-7/32 2-3/32 1-11/16 .35802-207SR1 1-1/2x1-1/2x1/4 27/32 1-31/32 2-1/4 2-19/32 4-15/32 2-11/32 1-3/4 .49802-211SR 1-1/2x1-1/2x1 27/32 1-7/32 2-1/4 2-1/8 4-15/32 2-3/8 1-11/16 .42802-212SR 1-1/2x1-1/2x1-1/4 1-1/32 1-5/32 2-7/16 2-3/32 4-27/32 2-3/8 2-1/16 .49802-247SR 2x2x1/2 1/2 1-1/2 2 2-1/4 4 2-7/8 1-3/16 .45802-248SR 2x2x3/4 19/32 1-13/32 2-1/8 2-1/8 4-1/4 2-7/8 1-3/8 .48802-287SR 2-1/2x2-1/2x1/2 9/16 1-3/4 2-5/16 2-1/2 4-19/32 3-1/2 1-7/32 .75802-331SR1 3x3x1/4 1-13/32 4-1/2 3-5/16 5-1/32 6-9/16 4-3/16 27/32 1.90802-413SR1 4x4x1/4 1-7/16 5-3/16 3-11/16 5-25/32 7-3/8 5-1/4 27/32 2.63

1 Outlet sized with bushing

TEEFipt x Fipt x Fipt

Part Number Size G H L M Approx. Wt. (Lbs.)805-002 1/4 1/2 1-3/32 2-3/16 27/32 .06805-003 3/8 9/16 1-5/32 2-5/16 15/16 .07805-005 1/2 17/32 1-1/4 2-15/32 1-3/16 .11805-007 3/4 21/32 1-15/32 2-15/16 1-1/2 .19805-010 1 3/4 1-23/32 3-7/16 1-27/32 .34805-012 1-1/4 15/16 1-31/32 3-29/32 2-1/4 .47805-015 1-1/2 1-1/8 2-3/16 4-3/8 2-13/32 .60805-020 2 1-5/8 2-5/8 5-1/4 3 1.08805-025 2-1/2 1-9/16 3-1/8 6-1/4 3-19/32 1.65805-030 3 1-15/16 3-9/16 7-3/32 4-11/32 2.82805-040 4 2-1/2 4-7/32 8-7/16 5-7/16 4.37

805-060F 6 8-5/8 10-1/8 20-1/4 7-3/16 20.11

M

HG

L

H1

M

H G

L

G1

M1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (16)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 351 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED TEESR Fipt x SR Fipt x SR Fipt

G H

L

M

Part Number Size G H L M Approx. Wt. (Lbs.)

805-002SR 1/4 17/32 1-1/8 2-1/4 27/32 .08

805-003SR 3/8 19/32 1-3/16 2-11/32 31/32 .09

805-005SR 1/2 1/2 1-1/4 2-1/2 1-3/16 .14

805-007SR 3/4 19/32 1-11/32 2-11/16 1-3/8 .16

805-010SR 1 7/8 1-25/32 3-9/16 1-11/16 .32

805-015SR 1-1/2 1-1/4 2-3/16 4-13/32 2-13/32 .66

805-020SR 2 1-5/8 2-5/8 5-1/4 3 1.17

STREET TEESpigot x Socket x Socket

M1

H1

L

M2

G1

H2 G2

H G

Part Number Size G G1 G2 H H1 H2 L M1 M2 Approx. Wt. (Lbs.)

844-005 1/2 23/32 23/32 1/2 1-19/32 1-21/32 1-19/32 3-5/32 1-3/16 1-3/16 .10

844-007 3/4 13/16 27/32 7/8 1-13/16 1-7/8 1-13/16 3-5/8 1-13/32 1-13/32 .15

844-010 1 1-3/32 13/16 13/16 2-7/32 2 2 4-7/32 1-3/4 1-3/4 .26

844-012 1-1/4 1-1/4 1-5/32 1-1/8 2-7/16 2-5/16 2-7/16 4-7/8 2-3/32 2-3/32 .39

844-015 1-1/2 1-13/16 1-1/8 1-1/8 2-7/8 2-9/16 2-9/16 5-11/32 2-11/32 2-11/32 .51

844-020 2 1-23/32 1-7/16 1-13/32 3-1/4 2-15/16 2-15/16 6-5/32 2-7/8 2-7/8 .80

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (17)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 352Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

90° ELBOWSocket x Socket

H

M

G

Part Number Size G H M Approx. Wt. (Lbs.)806-002 1/4 11/32 1 13/16 .03

806-003 3/8 15/32 1-1/4 31/32 .05

806-005 1/2 9/16 1-15/32 1-3/16 .08

806-007 3/4 5/8 1-11/16 1-7/16 .12

806-010 1 7/8 2 1-3/4 .20

806-012 1-1/4 1-1/32 2-9/32 2-1/8 .30

806-015 1-1/2 1-5/32 1-9/16 2-3/8 .39

806-020 2 1-13/32 2-15/16 2-7/8 .60

806-025 2-1/2 1-9/16 3-11/32 3-15/32 1.09

806-030 3 2-1/16 3-31/32 4-3/16 1.60

806-040 4 2-5/8 4-7/8 5-7/32 2.78

806-045F 4-1/2 6-1/2 9 5-5/8 4.58

806-050 5 3 5-3/4 6-3/8 4.42

806-050F 5 5-1/2 8-1/2 6-5/16 6.23

806-060 6 3-3/4 6-3/4 7-19/32 7.47

806-080 8 4-25/32 8-25/32 9-3/4 14.30

806-080F 8 7-7/8 12-1/8 9-5/8 17.47

806-100 10 5-25/32 10-13/16 12-5/32 26.34

806-100F 10 10 15-1/4 11-15/16 31.86

806-120 12 6-27/32 12-29/32 14-3/8 44.06

806-120F 12 11-1/2 17-3/4 14-1/8 60.28

806-140 14 7-1/2 14-1/2 15-11/16 53.05

806-140F 14 13-1/2 20-1/2 15-1/2 82.49

806-160F 16 15-9/16 23-9/16 17-11/16 101.71

806-180F 18 17-11/16 26-11/16 19-7/8 167.49

806-200F 20 19-13/16 29-13/16 22-1/16 193.41

806-240F 24 24 36 26-7/16 403.66

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (18)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 353 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

90° LONG SWEEP ELBOWSocket x Socket

M

GH

Part Number Size G H M Approx. Wt. (Lbs.)

806-005LSF 1/2 1-7/8 2-3/4 1-1/8 .13

806-007LSF 3/4 2-7/16 3-7/16 1-7/16 .22

806-010LSF 1 2-7/8 4 1-11/16 .33

806-012LSF 1-1/4 3-5/8 4-7/8 2-1/16 .50

806-015LSF 1-1/2 4-1/8 5-1/2 2-5/16 .60

806-020LSF 2 4-3/4 6-5/16 2-13/16 .90

806-025LSF 2-1/2 5-3/4 7-3/4 3-7/16 1.65

806-030LSF 3 7 9 4-1/8 2.36

806-040LSF 4 9 11-1/4 5-3/16 4.76

806-060LSF 6 13 16-1/4 7-1/2 12.84

806-080LSF 8 23-1/2 27-3/4 9-5/8 31.58

90° SWEEP ELBOWSocket x Socket

M

GH

Part Number Size G H M Approx. Wt. (Lbs.)

806-005S 1/2 27/32 1-23/32 1-3/16 .08

806-007S 3/4 1-1/32 2-1/32 1-13/32 .12

806-010S 1 1-5/16 2-7/16 1-23/32 .20

806-012S 1-1/4 1-9/16 2-13/16 2-3/32 .30

806-015S 1-1/2 1-3/4 3-1/8 2-11/32 .39

806-020S 2 2-5/16 3-13/16 2-7/8 .64

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (19)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 354Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

90° ELBOWSocket x Fipt

G

G1

H

H1

M

Part Number Size G G1 H H1 M Approx. Wt. (Lbs.)

807-002 1/4 5/16 5/16 15/16 15/16 7/8 .03

807-003 3/8 1/4 3/8 1-1/32 1-1/32 1-1/32 .05

807-005 1/2 15/32 9/16 1-11/32 1-9/32 1-3/16 .08

807-007 3/4 5/8 5/8 1-9/16 1-9/16 1-3/8 .09

807-010 1 11/16 25/32 1-13/16 1-11/16 1-23/32 .19

807-012 1-1/4 23/32 1-1/32 1-31/32 1-31/32 2-1/16 .28

807-015 1-1/2 15/16 1-7/32 2-11/32 2-5/32 2-3/8 .39

807-020 2 15/16 1-1/32 2-7/16 2 3 .80

807-030 3 1-27/32 2-7/32 3-23/32 3-9/16 4-9/32 1.72

807-040 4 2-5/16 2-7/8 4-9/16 4-9/32 5-1/4 2.87

807-0601 6 3-3/4 7-1/8 6-3/4 8-7/8 7-9/16 11.481 Outlet sized with Female Adapter

90°REDUCING ELBOWSocket x Fipt

Part Number Size G G1 H H1 M M1 Approx. Wt. (Lbs.)

807-101 3/4x1/2 1/2 25/32 1-17/32 1-17/32 1-13/32 1-3/16 .11

807-1301 1x1/2 27/32 1-17/32 1-31/32 2-1/4 1-23/32 1-23/32 .26

807-1311 1x3/4 7/8 1-17/32 2 2-1/4 1-3/4 1-3/4 .251 Outlet sized with Female Adapter

H

M1

M

H1 G1

G

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (20)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 355 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED 90° ELBOWSocket x SR Fipt

M

H

H1

G

G1

M1

Part Number Size G G1 H H1 M M1 Approx. Wt. (Lbs.)807-005SR 1/2 15/32 23/32 1-11/32 1-9/32 1-3/16 1-7/32 .08807-007SR 3/4 9/16 21/32 1-9/16 1-13/32 1-3/8 1-3/8 .11807-010SR 1 19/32 13/16 1-23/32 1-23/32 1-11/16 1-23/32 .20807-012SR 1-1/4 23/32 1-1/32 1-31/32 1-31/32 2-1/16 2-1/16 .30807-015SR 1-1/2 31/32 1-5/32 2-3/8 2-1/8 2-11/32 2-7/16 .41807-020SR 2 1-7/32 1-1/2 2-15/32 2-7/16 2-31/32 2-31/32 .83807-030SR 3 1-13/16 2-7/32 3-23/32 3-9/16 4-9/32 4-9/32 1.98807-040SR 4 2-9/32 2-25/32 4-9/16 4-7/32 5-1/4 5-1/4 2.94

SPECIAL REINFORCEDREDUCING 90° ELBOWSocket x SR Fipt

Part Number Size G G1 H H1 M M1 Approx. Wt. (Lbs.)807-101SR 3/4x1/2 1/2 13/16 1-17/32 1-17/32 1-13/32 1-3/16 .12807-130SR 1x1/2 9/16 1 1-23/32 1-5/8 1-23/32 1-3/16 .13

H

M1

M

H1 G1

G

TRANSITION 90° ELBOW Socket x Brass Fipt

Part Number Size G G1 H H1 M M1 Approx. Wt. (Lbs.)807-005BR 1/2 13/32 31/32 1-9/32 1-17/32 1-3/16 1-7/32 .15

807-007BR 3/4 1/2 1-5/32 1-1/2 1-25/32 1-3/8 1-13/32 .20

Not intended to convey or dispense water for human consumption through drinking or cooking

M

H

H1 G1

G M1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (21)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 356Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

90° ELBOWFipt x Fipt

Part Number Size G H M Approx. Wt. (Lbs.)808-002 1/4 11/32 15/16 7/8 .04808-003 3/8 9/16 1-5/32 15/16 .05808-005 1/2 1/2 1-7/32 1-9/32 .09808-007 3/4 5/8 1-3/8 1-3/8 .11808-010 1 25/32 1-5/8 1-23/32 .20808-012 1-1/4 15/16 1-7/8 2-1/16 .30808-015 1-1/2 1-5/32 2-3/32 2-7/16 .46808-020 2 1-9/16 2-17/32 3 .86808-025 2-1/2 1-5/8 3-3/16 3-9/16 1.20808-030 3 1-29/32 3-17/32 4-13/32 2.30808-040 4 2-15/32 4-3/16 5-15/32 3.35

M

H

G

SPECIAL REINFORCED 90° ELBOWSR Fipt x SR Fipt

Part Number Size G H M Approx. Wt. (Lbs.)808-003SR 3/8 9/16 1-5/32 15/16 .07808-005SR 1/2 1/2 1-7/32 1-3/16 .10808-007SR 3/4 5/8 1-3/8 1-3/8 .13808-010SR 1 25/32 1-11/16 1-23/32 .23808-012SR 1-1/4 15/16 1-7/8 2-1/16 .35808-015SR 1-1/2 1-1/32 2-1/8 2-7/16 .50808-020SR 2 1-19/32 2-1/2 3 .92

G

M

H

TRANSITION REDUCING 90° ELBOW Socket x Brass Fipt

Part Number Size G G1 H H1 M M1 Approx. Wt. (Lbs.)807-101BR 3/4x1/2 15/32 1-3/32 1-15/32 1-21/32 1-13/32 1-3/16 .17

Not intended to convey or dispense water for human consumption through drinking or cooking

H1 G1

M

M1

H

G

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (22)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 357 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

90° STREET ELBOWSpigot x Socket

Part Number Size G G1 H H1 M1 Approx. Wt. (Lbs.)809-005 1/2 13/16 7/16 1-21/32 1-7/16 1-5/32 .07809-007 3/4 29/32 11/16 1-27/32 1-11/16 1-3/8 .11809-010 1 1-3/32 27/32 2-7/32 2 1-23/32 .19809-012 1-1/4 1-9/32 13/16 2-19/32 2-1/4 2-3/32 .29809-015 1-1/2 1-7/16 1-3/16 2-13/16 2-9/16 2-3/8 .40809-020 2 1-3/4 1-7/16 3-1/4 2-31/32 2-7/8 .60809-025 2-1/2 2-1/2 1-5/8 4-1/2 3-3/8 3-7/16 1.31809-030 3 2-3/8 1-13/16 4-1/4 3-11/16 4-3/16 1.65809-040 4 3-1/32 2-1/4 5-9/32 4-17/32 5-1/4 2.82809-060 6 5-1/4 3-7/8 8-1/2 6-7/8 7-9/16 12.00809-080 8 7-1/8 4-25/32 11-1/8 8-25/32 9-3/4 17.21809-100 10 8-5/8 5-13/16 14-5/16 11-3/8 12-1/16 37.73809-120 12 10-1/8 6-7/8 16-7/8 13-3/8 14-1/8 61.75809-140 14 11-1/16 7-9/16 18-5/16 14-5/8 15-11/16 73.23

809-140F 14 13-1/2 13-1/2 20-1/2 20-1/2 15-1/2 82.49809-160F 16 19-9/16 15-9/16 28-9/16 23-9/16 17-11/16 120.78809-180F 18 22-3/16 17-11/16 32-3/16 26-11/16 19-7/8 140.91809-200F 20 24-13/16 19-13/16 35-13/16 29-13/16 22-1/16 256.44809-240F 24 30 24 43 36 26-7/16 395.00

PIPE O.D.

H1 G1

G

H

M1

90° STREET ELBOWMipt x Fipt

Part Number Size G G1 H H1 M1 Approx. Wt. (Lbs.)812-002 1/4 17/32 5/16 1-1/32 29/32 13/16 .02812-005 1/2 11/16 13/32 1-11/32 1-5/32 1-3/16 .06812-007 3/4 7/8 17/32 1-1/2 1-9/32 1-7/16 .09812-010 1 1-1/32 21/32 1-13/16 1-9/16 1-3/4 .15812-012 1-1/4 2-9/16 1 3-9/32 1-31/32 2-7/32 .49812-0151 1-1/2 2-11/16 1-1/4 3-7/16 2-1/8 2-13/32 .54

1 Outlet sized with Female Adapter

M1 G

H

G1 H1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (23)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 358Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

11-1/4° ELBOWSocket x Socket

Part Number Size H J M Approx. Wt. (Lbs.)811-015 1-1/2 1-19/32 7/32 2-3/8 .24811-020 2 1-23/32 7/32 2-27/32 .33

811-025F 2-1/2 2-11/16 11/16 3-7/16 .81811-030 3 2-3/16 5/16 4-1/8 .88811-040 4 2-21/32 13/32 5-1/4 1.53

811-045F 4-1/2 3-1/2 1 5-5/8 1.94811-050F 5 3-13/16 13/16 6-5/16 2.88811-060F 6 4-1/4 1 7-1/2 4.43811-080F 8 5-3/8 1-1/8 9-5/8 8.73811-100F 10 6-11/16 1-7/16 11-15/16 15.93811-120F 12 7-13/16 1-9/16 14-1/8 24.66811-140F 14 9 2 15-1/2 33.00811-160F 16 10-3/8 2-3/8 17-11/16 48.74811-180F 18 11-3/4 2-3/4 19-7/8 69.12811-200F 20 13-1/8 3-1/8 22-1/16 96.58811-240F 24 15-13/16 3-13/16 26-7/16 152.00

M

H

J

30° ELBOWSocket x Socket

Part Number Size H J M Approx. Wt. (Lbs.)815-005F 1/2 1-7/16 7/16 1-1/8 .07815-007F 3/4 1-7/16 7/16 1-3/8 .09815-010F 1 1-3/4 1/2 1-11/16 .14815-012F 1-1/4 2-3/16 11/16 2-1/16 .22815-015F 1-1/2 2-3/16 11/16 2-5/16 .30815-020F 2 2-1/2 3/4 2-13/16 .46815-025F 2-1/2 2-1/2 3/4 3-7/16 .81815-030F 3 3-5/16 1-1/16 4-1/8 1.21815-040F 4 3-7/16 1-3/16 5-3/16 2.14815-045F 4-1/2 4 1-1/2 5-5/8 2.18815-050F 5 4-3/8 1-3/8 6-5/16 3.10815-060 6 4-13/16 1-7/8 7-9/16 5.59

H

J

M

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (24)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 359 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

22-1/2° ELBOWSocket x Socket

M

H

J

Part Number Size H J M Approx. Wt. (Lbs.)816-005 1/2 1-1/16 3/16 1-5/32 .06

816-007 3/4 1-3/16 3/16 1-7/16 .09

816-010 1 1-3/8 9/32 1-23/32 .13

816-012 1-1/4 1-1/2 5/16 2-3/32 .19

816-015 1-1/2 1-21/32 1/4 2-3/8 .26

816-015F 1-1/2 2-1/8 5/8 2-5/16 .26

816-020 2 1-7/8 7/16 2-7/8 .38

816-025 2-1/2 2-7/32 15/32 3-1/2 .68

816-025F 2-1/2 2-7/8 7/8 3-7/16 .75

816-030 3 2-13/32 9/16 4-5/32 .95

816-040 4 2-7/8 5/8 5-1/4 1.64

816-045F 4-1/2 3-13/16 1-5/16 5-5/8 2.09

816-050F 5 4-1/8 1-1/8 6-5/16 3.15

30° ELBOWSocket x Socket

Part Number Size H J M Approx. Wt. (Lbs.)815-080F 8 6-3/16 1-15/16 9-5/8 10.08

815-100F 10 7-3/4 2-1/2 11-15/16 17.92

815-120F 12 9-1/16 2-13/16 14-1/8 27.40

815-140F 14 10-7/16 3-7/16 15-1/2 37.94

815-160F 16 11-15/16 3-15/16 17-11/16 55.09

815-180F 18 13-7/16 4-7/16 19-7/8 77.09

815-200F 20 15 5 22-1/16 119.89

815-240F 24 18-1/8 6-1/8 26-7/16 166.30

H

J

M

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (25)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 360Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

22-1/2° ELBOWSocket x Socket

M

H

J

Part Number Size H J M Approx. Wt. (Lbs.)816-060 6 4-9/16 1-3/8 7-7/16 4.33

816-060F 6 4-5/8 1-3/8 7-1/2 5.02816-080 8 5-1/16 1-1/32 9-3/4 8.19

816-080F 8 5-7/8 1-5/8 9-5/8 9.41816-100F 10 7-5/16 2-1/16 11-15/16 17.25816-120F 12 8-9/16 2-5/16 14-1/8 26.03816-140F 14 9-13/16 2-13/16 15-1/2 34.65816-160F 16 11-5/16 3-5/16 17-11/16 52.97816-180F 18 12-3/4 3-3/4 19-7/8 74.44816-200F 20 14-1/4 4-1/4 22-1/16 119.89816-240F 24 17-3/16 5-3/16 26-7/16 189.96

22-1/2° STREET ELBOWSpigot x Socket

Part Number Size H H1 J J1 M1 Approx. Wt. (Lbs.)842-005 1/2 7/8 1 1/8 1/8 1-3/16 .05842-007 3/4 1-1/4 1-5/32 3/16 3/16 1-3/8 .08842-010 1 1-7/16 1-11/32 5/16 7/32 1-23/32 .13842-012 1-1/4 1-9/16 1-9/16 5/16 3/8 2-3/32 .20842-015 1-1/2 1-21/32 1-7/8 9/32 1/2 2-3/8 .26842-020 2 2 1-29/32 15/32 13/32 2-7/8 .40842-025 2-1/2 2-7/32 2-7/32 15/32 15/32 3-1/2 .66842-030 3 2-1/2 2-5/16 21/32 7/16 4-5/32 1.44842-040 4 2-27/32 3-1/32 9/16 25/32 5-1/4 1.67842-060 6 5-11/16 3-15/16 2-3/8 7/8 7-5/8 9.46842-080 8 7-3/8 5-1/8 3-1/8 1-1/8 9-3/4 5.61

PIPE O.D.

M1

H

H1

J

J1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (26)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 361 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

45° ELBOWSocket x Socket

M

H

J

Part Number Size H J M Approx. Wt. (Lbs.)

817-002 1/4 13/16 5/32 27/32 .03

817-003 3/8 31/32 7/32 1 .04

817-005 1/2 1-1/8 1/4 1-3/16 .06

817-007 3/4 1-5/16 5/16 1-7/16 .09

817-010 1 1-7/16 5/16 1-23/32 .15

817-012 1-1/4 1-5/8 3/8 2-1/8 .23

817-015 1-1/2 1-13/16 7/16 2-3/8 .30

817-020 2 2-1/8 5/8 2-7/8 .46

817-025 2-1/2 2-13/32 21/32 3-1/2 .77

817-030 3 2-29/32 29/32 4-5/32 1.12

817-040 4 3-5/16 1-1/16 5-1/4 2.00

817-045F 4-1/2 4-1/2 2 5-5/8 2.32

817-050 5 4 1-11/32 6-13/32 3.23

817-050F 5 4-7/8 1-7/8 6-5/16 3.86

817-060 6 4-3/4 1-3/4 7-19/32 5.52

817-080 8 6 2 9-3/4 10.17

817-100 10 7-5/8 2-19/32 12-1/8 18.99

817-100F 10 8-11/16 3-7/16 11-15/16 19.91

817-120 12 9-11/16 3-3/32 14-13/32 34.04

817-120F 12 10-1/8 3-7/8 14-1/8 31.51

817-140 14 10-5/16 3-5/16 15-5/8 40.00

817-140F 14 11-9/16 4-9/16 15-1/2 42.89

817-160F 16 13-5/16 5-5/16 17-11/16 61.45

817-180F 18 15 6 19-7/8 87.73

817-200F 20 16-3/4 6-3/4 22-1/16 107.05

817-240F 24 20-3/16 8-3/16 26-7/16 204.20

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (27)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 362Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

15° ELBOWSocket x Socket

M

H

J

Part Number Size H J M Approx. Wt. (Lbs.)

818-020F 2 2-5/16 9/16 2-13/16 .42

818-025F 2-1/2 2-3/4 3/4 3-7/16 .79

818-030F 3 3 3/4 4-1/8 1.10

818-040F 4 3-1/8 7/8 5-3/16 1.90

818-045F 4-1/2 3-5/8 1-1/2 5-5/8 2.00

818-050F 5 3-15/16 15/16 6-5/16 2.98

818-060F 6 4-3/8 1-1/8 7-1/2 4.43

818-080F 8 4-1/2 1-1/4 9-5/8 8.73

818-100F 10 6-15/16 1-11/16 11-15/16 15.93

818-120F 12 8-1/16 1-13/16 14-1/8 24.66

818-140F 14 9-5/16 2-5/16 15-1/2 34.65

818-160F 16 10-11/16 2-11/16 17-11/16 50.85

818-180F 18 12-1/16 3-1/16 19-7/8 71.78

818-200F 20 13-1/2 3-1/2 22-1/16 119.89

818-240F 24 16-1/4 4-1/4 26-7/16 170.96

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (28)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 363 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

45° ELBOWFipt x Fipt

H

J

M

Part Number Size H J M Approx. Wt. (Lbs.)

819-002 1/4 25/32 3/16 27/32 .03

819-003 3/8 13/16 3/16 1 .04

819-005 1/2 31/32 5/16 1-3/16 .07

819-007 3/4 1-3/32 13/32 1-3/8 .11

819-010 1 1-7/32 7/32 1-11/16 .14

819-012 1-1/4 1-7/16 7/16 2-3/16 .24

819-015 1-1/2 1-1/2 15/32 2-1/2 .31

819-020 2 1-23/32 21/32 3 .46

819-025 2-1/2 2-17/32 31/32 3-1/2 1.14

819-030 3 2-23/32 1 4-9/32 1.78

819-040 4 3-1/4 1-7/32 5-1/4 2.71

SPECIAL REINFORCED 45° ELBOWSR Fipt x SR Fipt

H

M

J

Part Number Size H J M Approx. Wt. (Lbs.)

819-005SR 1/2 1 5/16 1-3/16 .09

819-007SR 3/4 1-1/8 13/32 1-3/8 .10

819-010SR 1 1-1/4 13/32 1-23/32 .17

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (29)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 364Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

60° ELBOWSocket x Socket

Part Number Size H J M Approx. Wt. (Lbs.)824-005F 1/2 1-5/8 5/8 1-1/8 .13824-007F 3/4 1-11/16 11/16 1-3/8 .18824-010F 1 2 3/4 1-11/16 .33824-012F 1-1/4 2-1/2 1 2-1/16 .68824-015F 1-1/2 2-5/8 1-1/8 1-3/8 .74824-020F 2 3 1-1/4 2-13/16 .93824-025F 2-1/2 3-9/16 1-9/16 3-7/16 .73824-030F 3 4 1-3/4 4-1/8 2.53824-040F 4 4-5/16 2-1/16 5-3/16 4.05824-050F 5 5-3/8 2-3/8 6-5/16 7.08824-060F 6 6-1/8 2-7/8 7-1/2 9.30824-080F 8 7-3/4 3-1/2 9-5/8 18.81824-100F 10 9-11/16 4-7/16 11-15/16 33.04824-120F 12 11-5/16 5-1/16 14-1/8 31.51824-140F 14 12-15/16 5-15/16 15-1/2 42.89824-160F 16 14-13/16 6-13/16 17-11/16 108.07824-180F 18 16-3/4 7-3/4 19-7/8 95.71824-200F 20 23-11/16 13-11/16 22-1/16 239.76824-240F 24 28-11/16 16-11/16 26-7/16 348.00

H

M

J

45° STREET ELBOWSpigot x Socket

Part Number Size H H1 J J1 M1 Approx. Wt. (Lbs.)827-005 1/2 1-9/32 1-5/16 11/32 7/16 1-3/16 .06827-007 3/4 1-1/2 1-1/2 7/16 1/2 1-13/32 .10827-010 1 1-25/32 1-1/2 19/32 3/8 1-3/4 .15827-012 1-1/4 2 1-23/32 5/8 15/32 2-3/32 .22827-015 1-1/2 2-1/32 2-1/8 19/32 25/32 2-11/32 .30827-020 2 2-5/16 2-11/32 11/16 3/8 2-27/32 .44827-025 2-1/2 3-11/16 2-9/16 1-11/16 13/16 3-1/2 1.09827-030 3 3-1/4 2-13/16 1-3/16 29/32 4-5/32 1.22827-040 4 3-13/16 3-13/16 1-9/32 1-9/16 5-1/4 2.15827-060 6 5-3/32 4-25/32 2-1/16 2-1/16 7-19/32 5.70827-080 8 6-5/8 5-31/32 2-19/32 1-3/4 9-3/4 10.53

J1 H1

M1

J H

PIPE O.D.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (30)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 365 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CROSS Socket x Socket x Socket x Socket

Part Number Size G G1 H H1 L L1 M Approx. Wt. (Lbs.)820-002 1/4 13/32 13/32 1-1/32 1-1/32 2-1/16 2-1/16 27/32 .05820-005 1/2 9/16 9/16 1-15/32 1-15/32 2-15/16 2-15/16 1-3/16 .13820-007 3/4 5/8 5/8 1-5/8 1-5/8 3-9/32 3-9/32 1-13/32 .22820-010 1 31/32 31/32 2-3/32 2-3/32 4-7/32 4-7/32 1-23/32 .39820-012 1-1/4 1-3/32 1-3/32 2-3/8 2-3/8 4-3/4 4-3/4 2-1/8 .63820-015 1-1/2 1-1/4 1-1/4 2-5/8 2-5/8 5-1/4 5-1/4 2-3/8 .80820-020 2 1-1/2 1-1/2 3 3 6 6 3 1.34820-025 2-1/2 1-11/16 1-11/16 3-15/32 3-15/32 6-29/32 6-29/32 3-17/32 2.02820-030 3 2-3/32 2-3/32 3-31/32 3-31/32 7-15/16 7-15/16 4-11/32 3.30820-040 4 2-5/8 2-5/8 4-7/8 4-7/8 9-3/4 9-3/4 5-11/32 5.31

820-050F 5 5-1/2 5-1/2 8-1/2 8-1/2 17 17 6-5/16 14.69820-060F 6 6-1/4 6-1/4 9-1/2 9-1/2 19 19 7-1/2 16.19820-080F 8 7-5/8 7-5/8 11-7/8 11-7/8 23-3/4 23-3/4 9-5/8 28.22820-100F 10 9 9 14-1/4 14-1/4 28-1/2 28-1/2 11-15/16 49.78820-120F 12 11-1/4 11-1/4 17-1/2 17-1/2 35 35 14-1/8 80.83820-140F 14 12-1/4 12-1/4 19-1/4 19-1/4 38-1/2 38-1/2 15-1/2 108.89820-160F 16 13 13 21 21 42 42 17-11/16 156.80820-180F 18 13-3/4 13-3/4 22-3/4 22-3/4 45-1/2 45-1/2 19-7/8 215.35820-200F 20 16-3/8 16-3/8 26-3/8 26-3/8 52-3/4 52-3/4 22-1/16 300.00820-240F 24 20-1/4 20-1/4 32-1/4 32-1/4 64-1/2 64-1/2 26-7/16 527.13

L1

L H

G

H1

G1

M

45° STREET ELBOWSpigot x Socket

Part Number Size H H1 J J1 M1 Approx. Wt. (Lbs.)827-100 10 10-21/32 8-3/16 2-19/32 5-5/16 12-3/16 25.62827-120 12 13-1/4 9-11/16 6-3/8 3-3/32 14-13/32 45.44

827-140F 14 11-9/16 11-9/16 4-9/16 4-9/16 15-1/2 61.04827-160F 16 18-5/16 13-5/16 9-5/16 5-5/16 17-11/16 78.40827-180F 18 20-1/2 15 10-1/2 6 19-7/8 114.32827-200F 20 22-3/4 16-3/4 11-3/4 6-3/4 22-1/16 156.53827-240F 24 27-3/16 20-3/16 14-3/16 8-3/16 26-7/16 261.19

J1 H1

M1

J H

PIPE O.D.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (31)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 366Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING CROSS Socket x Socket x Socket x Socket

M L1

L

H1

G1

M1

HG

Part Number Size G G1 H H1 L L1 M M1 Approx. Wt. (Lbs.)

820-1301 1x1x1/2x1/2 1 1-7/16 2-1/8 2-3/8 4-7/32 4-3/4 1-23/32 1-23/32 .56820-131 1x1x1/2x3/4 23/32 5/8 1-5/8 1-5/8 3-1/4 3-1/4 1-7/8 1-1/2 .30820-1661 1-1/4x1-1/4x1/2x1/2 1-3/32 1-3/32 2-3/8 2-11/16 4-3/4 5-3/16 3-3/32 3-3/32 .82820-167 1-1/4x1-1/4x3/4x3/4 1-1/16 23/32 2-1/16 1-31/32 4-3/32 3-31/32 2-1/16 1-13/32 .33820-2091 1-1/2x1-1/2x1/2x1/2 1-7/32 1-7/32 2-21/32 2-31/32 5-1/4 5-15/16 2-3/8 2-3/8 1.18820-210 1-1/2x1-1/2x3/4x3/4 11/16 1-5/32 2-3/32 2-3/16 4-3/16 4-11/32 2-3/8 1-13/32 .40820-2111 1-1/2x1-1/2x1x1 1-3/4 1-3/4 2-5/8 3 5-5/16 5-7/8 1-3/8 1-3/8 1.12820-248 2x2x3/4x3/4 11/16 1-7/16 2-7/32 2-7/16 4-13/32 4-7/8 2-29/32 1-13/32 .55820-2491 2x2x1x1 1-1/2 2-9/32 3 3-7/16 6 6-27/32 3 3 1.81820-251 2x2x1-1/2x1-1/2 1-1/2 2 3 3-3/8 6 6-3/4 2-7/8 2-7/8 1.72820-289 2-1/2x2-1/2x1x1 7/8 1-23/32 2-11/16 2-7/8 5-11/32 5-3/4 3-1/2 1-3/4 .97820-2911 2-1/2x2-1/2x1-1/2x1-1/2 1-11/16 2-15/32 3-7/16 3-27/32 6-7/8 7-23/32 3-9/16 3-9/16 2.83820-3361 3x3x1-1/4x1-1/4 2-3/32 3-1/8 3-31/32 4-3/8 7-29/32 8-3/4 4-3/16 4-3/16 4.23820-3381 3x3x2x2 2-3/32 2-27/32 3-31/32 4-5/16 7-29/32 8-5/8 4-13/32 4-5/16 4.23820-4201 4x4x2x2 2-5/8 3-13/16 4-7/8 5-11/32 9-3/4 10-21/32 5-11/32 5-7/32 7.33820-420F 4x4x2x2 3-7/8 4-1/4 6-1/8 6 12-1/4 12 5-3/16 2-13/16 5.26820-4221 4x4x3x3 2-5/8 3-7/16 4-7/8 5-5/16 9-3/4 10-5/8 5-1/4 5-1/4 6.94820-528F 6x6x2x2 4-5/8 5-3/16 7-7/8 6-15/16 15-3/4 13-7/8 7-1/2 2-13/16 7.19820-530F 6x6x3x3 4-3/4 5-3/4 8 8 16 16 7-1/2 4-1/8 12.60820-532F 6x6x4x4 5-1/4 6-3/4 8-1/2 9 17 18 7-1/2 5-3/16 14.54820-533F 6x6x5x5 5-3/4 6-1/2 9 9-1/2 18 19 7-1/2 6-5/16 14.00820-578F 8x8x2x2 4-11/16 6-1/8 8-15/16 7-7/8 17-7/8 15-3/4 9-5/8 2-13/16 11.30820-580F 8x8x3x3 5-3/16 6-11/16 9-7/16 8-15/16 18-7/8 17-7/8 9-5/8 4-1/8 12.93820-582F 8x8x4x4 5-3/4 7-11/16 10 9-15/16 20 19-7/8 9-5/8 5-3/16 21.87820-585F 8x8x6x6 6-3/4 8-1/16 11 11-5/16 22 22-5/8 9-5/8 7-1/2 30.04820-621F 10x10x2x2 4-3/8 7-1/8 9-5/8 8-7/8 19-1/4 17-11/16 11-15/16 2-13/16 19.45820-622F 10x10x2-1/2x2-1/2 5-1/4 7-5/16 10-1/2 9-5/16 21 18-5/8 11-15/16 3-7/16 20.00820-623F 10x10x3x3 4-7/8 7-11/16 10-1/8 9-15/16 20-1/4 19-13/16 11-15/16 4-1/8 21.42820-624F 10x10x4x4 5-3/8 8-11/16 10-5/8 10-15/16 21-1/4 21-13/16 11-15/16 5-3/16 24.17820-626F 10x10x6x6 5-7/8 9-1/16 11-1/8 12-5/16 22-1/4 24-5/8 11-15/16 7-1/2 40.79820-628F 10x10x8x8 8-1/4 9-15/16 13-1/2 14-3/16 27 28-3/8 11-15/16 9-5/8 65.94820-661F 12x12x2x2 4-3/4 8 11 9-3/4 22 19-1/2 14-1/8 2-13/16 29.32820-663F 12x12x3x3 5-1/4 8-9/16 11-1/2 10-13/16 23 21-5/8 14-1/8 4-1/8 33.02820-664F 12x12x4x4 5-3/4 9-9/16 12 11-13/16 24 23-5/8 14-1/8 5-3/16 33.78820-666F 12x12x6x6 7-1/4 9-15/16 13-1/4 13-3/16 26-1/2 26-3/8 14-1/8 7-1/2 57.20820-668F 12x12x8x8 8 10-13/16 14-1/4 15-1/16 28-1/2 30-1/8 14-1/8 9-5/8 66.12820-670F 12x12x10x10 10-1/4 10-13/16 16-1/2 16-1/16 33 32-1/8 14-1/8 11-15/16 105.91820-691F 14x14x2x2 5-3/16 8-9/16 12-3/16 10-5/16 24-3/8 20-5/8 15-1/2 2-13/16 38.49820-693F 14x14x3x3 5-3/4 9-1/8 12-3/4 11-3/8 25-1/2 22-3/4 15-1/2 4-1/8 49.59

1 Outlet sized with bushing

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (32)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 367 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING CROSS Socket x Socket x Socket x Socket

M L1

L

H1

G1

M1

HG

Part NumberSize G G1 H H1 L L1 M M1

Approx. Wt. (Lbs.)PVC PVC

820-694F 14x14x4x4 6-1/2 10-1/8 13-1/2 12-3/8 27 24-3/4 15-1/2 5-3/16 43.51

820-696F 14x14x6x6 8-1/4 10-1/2 15-1/4 13-3/4 30-1/2 27-1/2 15-1/2 7-1/2 78.72

820-698F 14x14x8x8 9-1/4 11-3/8 16-1/4 15-5/8 32-1/2 31-1/4 15-1/2 9-5/8 75.53

820-700F 14x14x10x10 10-1/8 11-3/8 17-1/8 16-5/8 34-1/4 33-1/4 15-1/2 11-15/16 95.66

820-702F 14x14x12x12 11 11-3/8 18 17-5/8 36 35-1/4 15-1/2 14-1/8 98.88

820-751F 16x16x2x2 5-7/8 9-1/2 13-7/8 11-1/4 27-3/4 22-1/2 17-11/16 2-13/16 55.64

820-752F 16x16x2-1/2x2-1/2 6 9-11/16 14 11-11/16 28 23-3/8 17-11/16 3-7/16 56.18

820-753F 16x16x3x3 6-5/16 10-1/16 14-5/16 12-5/16 28-5/8 24-5/8 17-11/16 4-1/8 58.72

820-754F 16x16x4x4 6-1/8 11-1/16 14-1/8 13-5/16 28-1/4 26-5/8 17-11/16 5-3/16 61.59

820-756F 16x16x6x6 8-5/8 11-7/16 16-5/8 14-11/16 33-1/4 29-3/8 17-11/16 7-1/2 93.13

820-758F 16x16x8x8 9-5/8 12-5/16 17-5/8 16-9/16 35-1/4 33-1/8 17-11/16 9-5/8 91.88

820-760F 16x16x10x10 10-5/8 12-5/16 18-5/8 17-9/16 37-1/4 35-1/8 17-11/16 11-15/16 104.59

820-762F 16x16x12x12 11-5/8 12-5/16 19-5/8 18-9/16 39-1/4 37-1/8 17-11/16 14-1/8 141.98

820-764F 16x16x14x14 12-3/4 12-11/16 20-3/4 19-11/16 41-1/2 39-3/8 17-11/16 15-1/2 129.00

820-784F 18x18x4x4 6-7/8 11-15/16 15-7/8 14-3/16 31-3/4 28-3/8 19-7/8 5-3/16 92.66

820-786F 18x18x6x6 8-1/2 12-5/16 17-1/2 15-9/16 35 31-1/8 19-7/8 7-1/2 118.63

820-788F 18x18x8x8 9-1/2 13-3/16 18-1/2 17-7/16 37 34-7/8 19-7/8 9-5/8 128.81

820-790F 18x18x10x10 10-1/2 13-3/16 19-1/2 18-7/16 39 36-7/8 19-7/8 11-15/16 130.87

820-792F 18x18x12x12 11-1/2 13-3/16 20-1/2 19-7/16 41 38-7/8 19-7/8 14-1/8 147.26

820-794F 18x18x14x14 12-3/4 13-9/16 21-3/4 20-9/16 43-1/2 41-1/8 19-11/16 15-1/2 164.25

820-796F 18x18x16x16 13-1/2 14-3/16 22-1/2 22-3/16 45 44-3/8 19-11/16 17-11/16 189.00

820-814F 20x20x4x4 7-11/16 12-7/8 17-11/16 15-1/8 35-3/8 30-1/4 22-1/16 5-3/16 115.50

820-816F 20x20x6x6 8-7/8 13-1/4 18-7/8 16-1/2 37-3/4 33 22-1/16 7-1/2 133.63

820-818F 20x20x8x8 9-7/8 14-1/8 19-7/8 18-3/8 39-3/4 36-3/4 22-1/16 9-5/8 153.30

820-820F 20x20x10x10 10-7/8 14-1/8 20-7/8 19-3/8 41-3/4 38-3/4 22-1/16 11-15/16 168.43

820-822F 20x20x12x12 11-7/8 14-1/8 21-7/8 20-3/8 43-3/4 40-3/4 22-1/16 14-1/8 186.06

820-824F 20x20x14x14 12-7/8 14-1/2 22-7/8 21-1/2 45-3/4 43 22-1/16 15-1/2 204.39

820-826F 20x20x16x16 14 15-1/8 24 23-1/8 48 46-1/4 22-1/16 17-11/16 230.10

820-828F 20x20x18x18 15 15 25 24 50 48 22-1/16 19-7/8 258.28

820-904F 24x24x4x4 9 14-11/16 21 16-15/16 42 33-7/8 26-7/16 5-3/16 192.22

820-906F 24x24x6x6 9-1/4 15-1/16 21-1/4 18-5/16 42-1/2 36-5/8 26-7/16 7-1/2 211.33

820-908F 24x24x8x8 10-1/4 15-15/16 22-1/4 20-3/16 44-1/2 40-3/8 26-7/16 9-5/8 221.76

820-910F 24x24x10x10 11-1/4 15-15/16 23-1/4 21-3/16 46-1/2 42-3/8 26-7/16 11-15/16 249.91

820-912F 24x24x12x12 12-1/4 15-15/16 24-1/4 22-3/16 48-1/2 44-3/8 26-7/16 14-1/8 279.88

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (33)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 368Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING CROSS Socket x Socket x Socket x Socket

M L1

L

H1

G1

M1

HG

Part Number Size G G1 H H1 L L1 M M1 Approx. Wt. (Lbs.)PVC PVC

820-914F 24x24x14x14 13-1/4 16-5/16 25-1/4 23-5/16 50-1/2 46-5/8 26-1/16 15-1/2 301.05

820-916F 24x24x16x16 14-3/4 16-15/16 26-3/4 24-15/16 53-1/2 49-7/8 26-7/16 17-11/16 329.60

820-918F 24x24x18x18 15-3/4 16-13/16 27-3/4 25-13/16 55-1/2 51-5/8 26-7/16 19-7/8 360.62

820-920F 24x24x20x20 16-3/4 18-3/16 28-3/4 28-3/16 57-1/2 56-3/8 26-7/16 22-1/16 398.22

COUPLING Socket x Socket

M

L N

Part Number Size L M N Approx. Wt. (Lbs.)829-002 1/4 1-3/8 27/32 1/16 .02829-003 3/8 1-5/8 1 3/32 .03829-005 1/2 1-7/8 1-3/16 1/8 .05829-007 3/4 2-1/8 1-13/32 1/8 .07829-010 1 2-15/32 1-23/32 3/16 .13829-012 1-1/4 2-23/32 2-7/32 7/32 .22829-015 1-1/2 2-7/8 2-11/32 3/32 .21829-020 2 3-1/8 2-27/32 3/32 .31829-025 2-1/2 3-11/16 3-15/32 1/4 .55829-030 3 3-31/32 4-5/32 3/16 .79829-040 4 4-3/4 5-5/16 1/4 1.34829-050 5 5-21/32 6-3/8 3/16 2.06

829-050F 5 7-3/8 6-5/16 1-3/8 2.60829-060 6 6-3/8 7-9/16 1/4 3.39829-080 8 8-1/4 9-23/32 9/32 6.55829-100 10 10-9/32 12-1/16 1/4 11.76

829-100F 10 12-1/2 11-15/16 2 13.94829-120 12 12-3/8 14-7/32 3/8 19.39

829-120F 12 14-1/4 14-1/8 1-3/4 21.92

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (34)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 369 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

COUPLING Socket x Socket

M

L N

Part Number Size L M N Approx. Wt. (Lbs.)829-140 14 14-7/16 15-5/8 3/8 29.70

829-140F 14 16-1/4 15-1/2 2-1/4 29.70 829-160F 16 19-1/2 17-11/16 3-1/2 42.38 829-180F 18 22 19-7/8 4 63.81 829-200F 20 23-3/4 22-1/16 3-3/4 86.58 829-240F 24 29-1/4 26-7/16 5-1/4 147.22

REDUCER COUPLING Socket x Socket

M1 M

N L

Part Number Size L M M1 N Approx. Wt. (Lbs.)829-101 3/4x1/2 2-3/32 1-13/32 1-5/32 7/32 .07829-130 1x1/2 2-3/16 1-23/32 1-13/32 7/32 .11829-131 1x3/4 2-13/32 1-23/32 1-13/32 1/4 .10829-166 1-1/4x1/2 2-9/16 2-3/32 1-5/32 7/16 .13829-167 1-1/4x3/4 2-19/32 2-3/32 1-5/8 11/32 .17829-168 1-1/4x1 2-11/16 2-1/8 1-3/4 5/16 .17829-209 1-1/2x1/2 2-27/32 2-11/32 1-3/16 19/32 .19829-210 1-1/2x3/4 2-7/8 2-3/8 1-13/32 17/32 .21829-211 1-1/2x1 2-7/8 2-11/32 1-15/16 3/8 .26829-212 1-1/2x1-1/4 2-13/16 2-13/32 2-1/8 5/32 .22829-247 2x1/2 3-3/32 2-7/8 1-5/32 11/16 .30829-248 2x3/4 3-7/32 2-7/8 1-13/32 23/32 .30829-249 2x1 3-1/8 2-7/8 1-23/32 17/32 .33829-250 2x1-1/4 3-11/32 2-7/8 2-3/32 19/32 .31829-251 2x1-1/2 3-7/32 2-27/32 2-11/32 1/4 .30829-2901 2-1/2x1-1/4 3-29/32 3-1/2 2-3/8 15/16 .57829-291 2-1/2x1-1/2 3-3/4 3-1/2 2-3/8 19/32 .51829-292 2-1/2x2 3-21/32 3-15/32 2-27/32 13/32 .48829-335 3x1 4-7/16 4-1/8 2-7/8 1-7/16 1.00829-3361 3x1-1/4 4-7/32 4-5/32 2-29/32 1-1/16 .94829-337 3x1-1/2 3-1/2 4-3/16 2-3/8 7/32 .71

1 Outlet sized with bushing

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (35)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 370Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER COUPLING Socket x Socket

M1 M

N L

Part Number Size L M M1 N Approx. Wt. (Lbs.)829-338 3x2 4 4-5/32 2-7/8 5/8 .74829-339 3x2-1/2 4-1/8 4-5/32 3-15/32 1/2 .77

829-339F 3x2-1/2 6 4-1/16 3-7/16 1-3/4 .90829-4161 4x3/4 5-23/32 5-9/32 2-29/32 2-13/32 1.67829-4171 4x1 5-15/16 5-9/32 2-29/32 2-17/32 1.71829-4191 4x1-1/2 5-23/32 5-9/32 2-29/32 2-1/16 1.59829-420 4x2 5-1/2 5-9/32 2-7/8 1-25/32 1.45829-421 4x2-1/2 4-9/16 5-3/16 3-1/2 17/32 1.25829-422 4x3 4-19/32 5-1/4 4-3/16 15/32 1.25

829-460F 4-1/2x4 6-15/16 5-5/8 5-3/16 2-3/16 1.97829-487F 5x2-1/2 8-1/8 6-1/4 5-3/16 3-5/8 2.64829-488F 5x3 7-15/16 6-1/4 5-3/16 2-15/16 3.08829-490F 5x4 7-3/4 6-1/4 5-3/16 2-1/2 2.09829-491F 5x4-1/2 8-3/16 6-1/4 5-5/8 2-15/16 3.22829-5281 6x2 7-1/16 7-1/2 5 2-9/16 4.37829-5291 6x2-1/2 6-31/32 7-19/32 5-9/32 2-3/16 4.30829-5301 6x3 7-1/8 7-9/16 5-9/32 2-1/4 4.07829-530F 6x3 9-3/16 7-5/16 5-3/16 3-15/16 3.85829-532 6x4 6-5/8 7-5/8 5-5/16 1-7/16 3.28

829-533F 6x5 8-15/16 7-3/8 6-5/16 2-11/16 3.57829-534F 6x4-1/2 9-5/16 7-5/16 5-5/8 3-9/16 3.22829-579F 8x2-1/2 15 9-1/2 5-3/16 8-3/4 8.33829-580F 8x3 14-15/16 9-1/2 5-3/16 8-11/16 7.95829-582 8x4 8-29/32 9-23/32 5-1/4 2-15/32 6.31

829-582F 8x4 14-5/8 9-1/2 5-3/16 8-1/8 8.17829-583F 8x5 14-11/16 9-1/2 6-5/16 7-7/16 7.78829-585 8x6 8 9-3/4 7-1/2 1 6.16

829-621F 10x2 21-1/2 11-3/4 5-3/16 14-3/4 16.16829-623F 10x3 21-7/16 11-3/4 5-3/16 14-3/16 15.77829-624F 10x4 21-1/8 11-3/4 5-3/16 13-5/8 17.13829-625F 10x5 21-3/16 11-3/4 6-5/16 12-15/16 16.38829-626 10x6 10-19/32 12-1/32 7-19/32 2-17/32 11.08

829-626F 10x6 17-1/2 11-3/4 7-1/2 9 14.72829-628 10x8 10-5/8 12 9-3/4 1-17/32 11.26

829-628F 10x8 13-1/4 11-3/4 9-5/8 3-3/4 11.42829-664F 12x4 28-3/8 13-15/16 5-3/16 19-7/8 31.70829-665F 12x5 28-7/16 13-15/16 6-5/16 19-3/16 27.25829-666F 12x6 24-3/4 13-15/16 7-1/2 15-1/4 26.96829-668 12x8 12-5/8 14-7/32 9-3/4 2-7/16 17.92

829-668F 12x8 20-1/2 13-15/16 9-5/8 10 24.341 Outlet sized with bushing

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (36)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 371 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER COUPLING Socket x Socket

M1 M

N L

Part Number Size L M M1 N Approx. Wt. (Lbs.)829-670F 12x10 16-3/8 13-15/16 11-15/16 4-7/8 18.92829-694F 14x4 30-1/8 15-3/16 5-3/16 20-7/8 31.56829-696F 14x6 26-1/2 15-3/16 7-1/2 16-1/4 29.65829-698F 14x8 22-1/4 15-3/16 9-5/8 11 29.32829-700F 14x10 18-1/8 15-3/16 11-15/16 5-7/8 22.90829-702F 14x12 17-3/4 15-3/8 14-1/8 4-1/2 27.40829-754F 16x4 38 17-3/8 5-3/16 27-3/4 50.97829-756F 16x6 34-3/8 17-3/8 7-1/2 23-1/8 61.19829-758F 16x8 30-1/8 17-3/8 9-5/8 17-7/8 52.73829-760F 16x10 26 17-3/8 11-15/16 12-3/4 43.70829-762F 16x12 20-1/4 17-3/8 14-1/8 6 34.25829-764F 16x14 21-1/4 17-1/2 15-1/2 5-1/4 42.89829-784F 18x4 47-3/8 19-11/16 5-3/16 36-1/8 104.77829-786F 18x6 43-3/4 19-11/16 7-1/2 31-1/2 91.02829-788F 18x8 39-1/2 19-11/16 9-5/8 26-1/4 86.65829-790F 18x10 35-3/8 19-11/16 11-15/16 21-1/8 91.28829-792F 18x12 29-5/8 19-11/16 14-1/8 14-3/8 73.27829-794F 18x14 29-5/8 19-11/16 15-1/2 13-5/8 73.72829-796F 18x16 23 19-11/16 17-11/16 6 55.09829-814F 20x4 58 21-7/8 5-3/16 45-3/4 152.76829-816F 20x6 54-1/2 21-7/8 7-1/2 41-1/8 136.93829-818F 20x8 50-1/8 21-7/8 9 -5/8 35-7/8 144.26829-820F 20x10 46 21-7/8 11-15/16 30-3/4 139.44829-822F 20x12 40-1/4 21-7/8 14- 1/8 24 119.04829-824F 20x14 40-1/4 21-7/8 15-1/2 23-1/4 118.17829-826F 20x16 33-5/8 21-7/8 17-11/16 15-5/8 100.87829-828F 20x18 25-1/2 21-7/8 19-7/8 6-1/2 79.76829-904F 24x4 71-1/2 26-1/16 5-3/16 57-1/4 231.96829-906F 24x6 67-7/8 26-1/16 7-1/2 52-5/8 229.16829-908F 24x8 63-5/8 26-1/16 9-5/8 47-3/8 223.42829-910F 24x10 59-1/2 26-1/16 11-15/16 42-1/4 218.80829-912F 24x12 53-3/4 26-1/16 14-1/8 35-1/2 192.82829-914F 24x14 53-3/4 26-1/16 15-1/2 34-3/4 225.10829-916F 24x16 47-1/8 26-1/16 17-11/16 27-1/8 171.54829-918F 24x18 39 26-1/16 19-7/8 18 147.20829-920F 24x20 30-5/8 26-1/16 22-1/16 8-5/8 116.56

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (37)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 372Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

ECCENTRIC REDUCER COUPLING Socket x Socket

M1 M

L N

Part Number Size L M M1 N Approx. Wt. (Lbs.)829-101FE 3/4x1/2 3-3/8 1-3/8 1-1/8 1-5/8 .09829-130FE 1x1/2 3-1/2 1-5/8 1-1/8 1-1/2 .12829-131FE 1x3/4 4 1-5/8 1-3/8 1-3/4 .13829-168FE 1-1/4x1 4-5/8 2 1-11/16 1-7/8 .24829-209FE 1-1/2x1/2 7-1/8 2-1/4 1-1/8 4-7/8 .30829-210FE 1-1/2x3/4 7-5/8 2-1/4 1-3/8 5-1/8 .33829-211FE 1-1/2x1 5-3/8 2-1/4 1-11/16 2-5/8 .33829-212FE 1-1/2x1-1/4 4-9/16 2-5/16 2-1/16 1-9/16 .37829-249FE 2x1 6-1/8 2-3/4 1-11/16 3-1/8 .39829-250FE 2x1-1/4 6-1/8 2-3/4 2-1/16 2-7/8 .37829-251FE 2x1-1/2 6 2-3/4 2-5/16 2-3/4 .46829-289FE 2-1/2x1 10-5/8 3-5/16 1-11/16 7-3/8 .88829-290FE 2-1/2x1-1/4 10-5/8 3-5/16 2-1/16 7-1/8 .91829-291FE 2-1/2x1-1/2 10-1/2 3-5/16 2-5/16 7 .91829-292FE 2-1/2x2 6-7/8 3-5/16 2-13/16 3-1/8 .68829-335FE 3x1 11-7/8 3-15/16 1-11/16 8-3/8 1.17829-336FE 3x1-1/4 11-7/8 3-15/16 2-1/16 8-1/8 1.10829-337FE 3x1-1/2 11-3/4 3-15/16 2-5/16 8 1.28829-338FE 3x2 5-7/8 4-5/32 2-7/8 2-15/32 1.01829-339FE 3x2-1/2 7-1/4 4-1/16 3-7/16 3 1.12829-417FE 4x1 17 5-1/8 1-11/16 13-1/2 2.75829-418FE 4x1-1/4 17 5-1/8 2-1/16 13-1/4 2.65829-419FE 4x1-1/2 16-7/8 5-1/8 2-5/16 13-1/8 3.10829-420FE 4x2 13-1/4 5-1/8 2-13/16 9-1/4 2.83829-421FE 4x2-1/2 12-3/8 5-1/8 3-7/16 8-1/8 2.42829-422FE 4x3 8-3/4 5-1/8 4-1/8 4-1/4 1.70829-528FE 6x2 20-7/8 7-5/16 2-13/16 15-7/8 5.86829-529FE 6x2-1/2 20 7-5/16 3-7/16 14-3/4 5.77829-530FE 6x3 16-3/8 7-5/16 4-1/8 10-7/8 6.24829-532FE 6x4 11-1/8 7-5/16 5-3/16 5-5/8 3.39829-533FE 6x5 11-1/4 7-3/8 6-5/16 5 4.32829-578FE 8x2 30-5/8 9-1/2 2-13/16 24-5/8 11.96829-580FE 8x3 26-1/8 9-1/2 4-1/8 19-5/8 11.13829-582FE 8x4 20-7/8 9-1/2 5-3/16 14-3/8 11.54829-583FE 8x5 21 9-1/2 6-5/16 13-3/4 10.77829-585FE 8x6 15-1/4 9-1/2 7-1/2 7-3/4 8.41829-624FE 10x4 32 11-3/4 5-3/16 24-1/2 25.43829-625FE 10x5 32-1/8 11-3/4 6-5/16 23-7/8 22.82829-626FE 10x6 26-3/8 11-3/4 7-1/2 17-7/8 22.31829-628FE 10x8 18-1/16 11-3/4 9-5/8 8-9/16 14.78829-664FE 12x4 43-1/2 13-15/16 5-3/16 35 42.54

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (38)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 373 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

FABRICATED REPAIR COUPLING Gasket x Gasket

L1

M1

L

M

Part Number Size L L1 M M1 Approx. Wt. (Lbs.)828-020F 2 9-1/8 6 2-13/16 3-3/16 .79828-030F 3 15-1/2 11-3/4 4-1/8 4-5/8 3.26828-040F 4 19-1/2 15 5-3/16 5-3/4 5.82828-060F 6 23 16 7-1/2 8-1/8 12.61828-080F 8 26-1/8 19 9-5/8 10-3/8 21.39828-100F 10 28 21-1/4 11-15/16 13-1/8 32.98828-120F 12 30 22-1/2 14-1/8 16-1/8 46.66828-140F 14 19 11-1/2 15-1/2 16-3/8 39.40828-160F 16 21-5/8 12-3/8 17-11/16 18-3/4 57.20

ECCENTRIC REDUCER COUPLING Socket x Socket

M1 M

L N

Part Number Size L M M1 N Approx. Wt. (Lbs.)829-665FE 12x5 43-5/8 13-15/16 6-5/16 34-3/8 41.73829-666FE 12x6 37-7/8 13-15/16 7-1/2 28-3/8 35.33829-668FE 12x8 29-9/16 13-15/16 9-5/8 19-1/16 32.68829-670FE 12x10 20-5/8 13-15/16 11-15/16 9-1/8 24.89829-696FE 14x6 41-3/8 15-3/16 7-1/2 31-1/8 56.76829-698FE 14x8 33-1/16 15-3/16 9-5/8 21-13/16 53.73829-700FE 14x10 24-1/8 15-3/16 11-15/16 11-7/8 51.42829-702FE 14x12 20-1/8 15-3/8 14-1/8 6-7/8 30.11829-756FE 16x6 54-1/4 17-1/2 7-1/2 43 113.09829-758FE 16x8 45-15/16 17-1/2 9-5/8 33-11/16 69.73829-760FE 16x10 37 17-1/2 11-15/16 23-3/4 59.25829-762FE 16x12 33 17-1/2 14-1/8 18-3/4 63.26`829-764FE 16x14 24-5/8 17-1/2 15-1/2 9-5/8 45.99829-786FE 18x6 69-1/4 19-11/16 7-1/2 57 145.31829-788FE 18x8 60-15/16 19-11/16 9-5/8 47-11/16 140.24829-790FE 18x10 52 19-11/16 11-15/16 37-3/4 109.43829-792FE 18x12 48 19-11/16 14-1/8 32-3/4 118.07829-794FE 18x14 39-5/8 19-11/16 15-1/2 23-5/8 97.05829-796FE 18x16 28-5/8 19-11/16 17-11/16 11-5/8 66.94

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (39)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 374Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED COUPLING SR Fipt x SR Fipt

M

L N

Part Number Size L M N Approx. Wt. (Lbs.)830-005SR 1/2 1-19/32 1-7/32 9/32 .06

830-007SR 3/4 1-5/8 1-3/8 1/8 .07

830-010SR 1 1-15/16 1-23/32 1/16 .13

830-012SR 1-1/4 2-1/16 2-1/16 5/16 .17

830-015SR 1-1/2 2-5/32 2-7/16 11/32 .27

830-020SR 2 2-1/4 3-1/32 1/4 .37

COUPLING Fipt x Fipt

M

L N

Part Number Size L M N Approx. Wt. (Lbs.)830-002 1/4 1-11/32 13/16 5/32 .03

830-003 3/8 1-15/32 1 9/32 .04

830-005 1/2 1-5/8 1-9/32 1/4 .07

830-007 3/4 1-11/16 1-5/8 3/32 .09

830-010 1 2-3/32 1-15/16 1/8 .15

830-012 1-1/4 2-3/16 2-9/32 3/16 .21

830-015 1-1/2 2-7/32 2-5/8 3/16 .28

830-020 2 2-7/32 3 7/32 .33

830-025 2-1/2 3-5/16 3-9/16 1/8 .68

830-030 3 3-15/32 4-3/8 21/32 1.12

830-040 4 3-21/32 5-9/16 3/16 1.52

830-060F 6 3-3/4 7-3/16 3/4 1.65

830-080F 8 4-1/2 9-3/8 1-1/16 2.84

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (40)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 375 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER COUPLING Fipt x Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)830-0721 1/2x1/4 1-31/32 1-5/16 1-5/32 5/8 .07830-0731 1/2x3/8 1-29/32 1-7/32 1-7/32 19/32 .06830-101 3/4x1/2 1-23/32 1-3/8 1-7/32 7/32 .07830-2111 1-1/2x1 2-7/8 2-11/32 2-11/32 1-1/32 .27

1 Outlet sized with bushing

M M1

N

L

SPECIAL REINFORCED REDUCER COUPLING SR Fipt x SR Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)830-101SR 3/4x1/2 1-23/32 1-3/8 1-7/32 7/32 .08830-130SR 1x1/2 2-1/4 1-23/32 1-7/32 21/32 .16830-131SR 1x3/4 2-13/32 1-23/32 1-3/8 23/32 .14830-210SR 1-1/2x3/4 2-7/8 2-7/16 1-3/8 1-7/32 .28830-211SR 1-1/2x1 2-15/16 2-7/16 1-11/16 7/16 .35830-212SR 1-1/2x1-1/4 2-7/8 2-1/2 2-3/32 15/16 .33830-249SR 2x1 3-3/16 3 1-23/32 1-17/32 .46830-251SR 2x1-1/2 3-1/4 3 2-7/16 1-7/16 .43

M M1

N

L

GROOVED COUPLING ADAPTER Groove x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)833-012 1-1/4 2-13/16 2-1/16 1-9/16 .18833-015 1-1/2 2-29/32 2-11/32 1-1/2 .19833-020 2 3-1/16 2-7/8 1-9/16 .29833-025 2-1/2 3-3/8 3-1/2 1-5/8 .49833-030 3 3-9/16 4-3/16 1-11/16 .68

L

PIPE O.D. M1

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (41)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 376Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

FEMALE ADAPTER Socket x Fipt

Part Number Size L M N Approx. Wt. (Lbs.)835-002 1/4 1-11/32 27/32 3/32 .02835-003 3/8 1-15/32 1 3/32 .04835-005 1/2 1-23/32 1-5/32 3/32 .05835-007 3/4 1-27/32 1-13/32 3/32 .07835-010 1 2-1/8 1-23/32 3/32 .11835-012 1-1/4 2-5/16 2-3/32 3/32 .16835-015 1-1/2 2-1/2 2-11/32 3/32 .20835-020 2 3 3-1/32 1/4 .41835-025 2-1/2 3-1/4 3-9/16 7/32 .63835-030 3 3-15/32 4-1/4 3/16 .74835-040 4 3-31/32 5-7/32 1/4 1.19835-060 6 4-31/32 7-21/32 5/16 3.12835-080 8 6-5/32 9-23/32 1/4 5.19

835-080F 8 8-9/16 9-5/8 2-9/16 6.19835-100F 10 10-1/4 11-15/16 3 10.88835-120F 12 11-1/8 14-1/8 2-5/8 16.56

L N

M

RISER EXTENSIONFipt x Mipt

Part Number Size L M N Approx. Wt. (Lbs.)834-007 3/4 2-13/16 1-7/16 1-15/32 .11

M

N

L

RISERO.D.

GROOVED COUPLING ADAPTER Groove x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)833-040 4 4-17/32 5-1/4 2-9/32 1.28

833-050F 5 7 6-5/16 4 2.14833-060 6 5-5/16 7-9/16 2-5/16 2.78

833-080F 8 8-3/16 9-5/8 3-15/16 6.19833-100F 10 9-7/8 11-15/16 4-5/8 10.62833-120F 12 10-7/8 14-1/8 4-5/8 21.92

L

PIPE O.D. M1

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (42)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 377 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED FEMALE ADAPTER Socket x SR Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-002SR 1/4 1-13/32 27/32 27/32 3/32 .03

835-003SR 3/8 1-15/32 15/16 31/32 3/32 .04

835-005SR 1/2 1-23/32 1-5/32 1-3/16 3/32 .06

835-007SR 3/4 1-7/8 1-13/32 1-3/8 3/32 .08

835-010SR 1 2-1/8 1-11/16 1-23/32 3/32 .13

835-012SR 1-1/4 2-5/16 2-3/32 2-1/16 3/32 .18

835-015SR 1-1/2 2-7/16 2-13/32 2-7/16 7/32 .26

835-020SR 2 2-23/32 3 3-1/32 1/4 .44

835-025SR 2-1/2 3-1/4 3-9/16 3-9/16 11/32 .68

835-030SR 3 3-1/2 4-1/4 4-9/32 7/32 .96

835-040SR 4 3-31/32 5-7/32 5-1/4 7/32 1.29

835-060SR 6 4-31/32 7-5/8 7-21/32 1/4 3.17

REDUCING FEMALE ADAPTER Socket x Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-098 3/4x1/4 1-15/16 1-13/32 27/32 13/32 .06

L

M1 M

N

L

M1

N

M

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (43)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 378Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TRANSITION FEMALE ADAPTER Socket x Brass Fipt Dimensions Also Applicable to 835-XXXSS

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-005BR 1/2 1-25/32 1-5/32 1-7/32 5/8 .11

835-007BR 3/4 2 1-13/32 1-3/8 3/8 .23

835-010BR 1 2-7/32 1-3/4 1-11/16 13/32 .25

835-012BR 1-1/4 2-3/8 2-3/32 2-1/16 3/8 .35

835-015BR 1-1/2 2-17/32 2-13/32 2-7/16 13/32 .46

835-020BR 2 2-25/32 2-7/8 3-3/16 7/16 1.03

Not intended to convey or dispense water for human consumption through drinking or cooking

M M1

N

L

SPECIAL REINFORCED REDUCING FEMALE ADAPTER Socket x SR Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-074SR 1/2x3/4 1-3/4 1-3/16 1-3/8 7/32 .07

835-098SR 3/4x1/4 1-15/16 1-13/32 27/32 13/32 .06

835-101SR 3/4x1/2 1-7/8 1-3/8 1-3/16 3/16 .07

835-102SR 3/4x1 2-1/16 1-7/16 1-11/16 7/32 .12

835-130SR 1x1/2 2 1-11/16 1-3/16 7/32 .10

835-131SR 1x3/4 2-3/32 1-3/4 1-3/8 1/4 .12

L

M1 M

N

TRANSITION REDUCING FEMALE ADAPTER Socket x Brass Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-101BR 3/4x1/2 2-1/32 1-7/16 1-3/16 15/32 .17

Not intended to convey or dispense water for human consumption through drinking or cooking

M1 M

L N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (44)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 379 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

MALE ADAPTER Spigot x Mipt

Part Number Size L N Approx. Wt. (Lbs.)861-005 1/2 1-13/16 5/16 .03861-007 3/4 1-31/32 5/16 .05861-010 1 2-3/32 1/4 .07861-131 1x3/4 2 1/4 .07861-012 1-1/4 2-9/32 9/32 .11861-015 1-1/2 2-5/8 11/32 .15861-020 2 2-13/16 13/32 .23

PIPEO.D.

NL

SPECIAL REINFORCED SPIGOTFEMALE ADAPTER Spigot x SR Fipt

Part Number Size L M1 N Approx. Wt. (Lbs.)878-005SR 1/2 1-3/4 1-3/16 5/32 .05878-007SR 3/4 1-15/16 1-3/8 3/16 .07878-010SR 1 2-1/4 1-11/16 7/32 .13878-012SR 1-1/4 2-15/32 2-1/16 1/4 .18878-015SR 1-1/2 2-21/32 2-7/16 13/32 .25

PIPEO.D.

LN

M1

ENCAPSULATED SPECIAL REINFORCED FEMALE ADAPTER Socket x ESR Fipt

Part Number Size L M M1 N Approx. Wt. (Lbs.)835-002ESR 1/4 1-1/2 27/32 29/32 3/32 .04835-003ESR 3/8 1-17/32 15/16 1-1/32 3/16 .04835-005ESR 1/2 1-7/8 1-3/16 1-9/32 9/32 .08835-007ESR 3/4 2 1-13/32 1-15/32 1/8 .10835-010ESR 1 2-1/4 1-3/4 1-13/16 1/8 .13835-012ESR 1-1/4 2-7/16 2-1/8 2-5/32 3/16 .21835-015ESR 1-1/2 2-9/16 2-13/32 2-1/2 1/4 .29835-020ESR 2 2-27/32 3 3-3/32 13/32 .46

M M1

N

L

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (45)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 380Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED SPIGOTFEMALE ADAPTER Spigot x SR Fipt

Part Number Size L M1 N Approx. Wt. (Lbs.)878-020SR 2 2-13/16 3 3/8 .39878-030SR 3 3-27/32 4-9/32 17/32 .91878-040SR 4 4-3/8 5-1/4 5/8 1.36

PIPEO.D.

LN

M1

SPECIAL REINFORCED REDUCINGSPIGOT FEMALE ADAPTER Spigot x SR Fipt

Part Number Size L M1 N Approx. Wt. (Lbs.)878-072SR 1/2x1/4 1-13/32 27/32 3/16 .03878-098SR 3/4x1/4 1-27/32 27/32 7/32 .05878-128SR 1x1/4 2-3/8 27/32 21/32 .08

L

M1

N

PIPE O.D.

ENCAPSULATED SPECIAL REINFORCED SPIGOT FEMALE ADAPTER Spigot x ESR Fipt

Part Number Size L M1 N Approx. Wt. (Lbs.)878-005ESR 1/2 1-7/8 1-9/32 3/16 .06878-007ESR 3/4 2-1/16 1-15/32 3/8 .09878-010ESR 1 2-3/8 1-25/32 11/32 .14878-012ESR 1-1/4 2-19/32 2-5/32 5/16 .20878-015ESR 1-1/2 2-3/4 2-1/2 13/32 .27878-020ESR 2 2-15/16 3-3/32 5/16 .41

L

PIPE O.D.

N

M1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (46)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 381 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TRANSITION FEMALE ADAPTER Spigot x Brass Fipt

Part Number Size L M1 N Approx. Wt. (Lbs.)

878-005BR 1/2 1-15/16 1-3/16 1/2 .11

878-007BR 3/4 2-5/32 1-3/8 17/32 .14

878-010BR 1 2-9/32 1-23/32 13/32 .22

Not intended to convey or dispense water for human consumption through drinking or cooking

MALE ADAPTERMipt x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)

836-005 1/2 1-23/32 1-5/32 3/16 .04

836-007 3/4 1-27/32 1-7/16 7/32 .06

836-010 1 2-5/32 1-23/32 7/32 .10

836-012 1-1/4 2-1/4 2-1/8 1/32 .15

836-015 1-1/2 2-9/16 2-13/32 9/32 .19

836-020 2 2-7/8 2-7/8 5/16 .28

836-025 2-1/2 3-21/32 3-17/32 11/32 .52

836-030 3 3-7/8 4-1/4 3/8 .74

836-040 4 4-13/32 5-5/16 13/32 1.15

836-050F 5 6 6-5/16 1-5/8 2.07

836-060 6 5-1/2 7-9/16 19/32 2.89

836-080F 8 8-3/16 9-5/8 2-3/16 6.00

836-100F 10 10-3/8 11-15/16 3-3/16 10.95

836-120F 12 11-1/8 14-1/8 2-3/4 16.44

M1

L N

PIPE O.D. M1

LN

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (47)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 382Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TRANSITION MALE ADAPTERBrass Mipt x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)836-005BR 1/2 2-13/32 1-9/32 27/32 .19836-007BR 3/4 2-17/32 1-13/32 13/16 .26836-010BR 1 2-15/16 1-23/32 29/32 .43836-012BR 1-1/4 3-1/8 2-3/32 31/32 .66836-015BR 1-1/2 3-9/32 2-11/32 1 .79836-020BR 2 3-7/16 2-27/32 31/32 .99

REDUCING MALE ADAPTERMipt x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)836-053 3/8x1/2 1-11/16 1-3/16 1/4 .04836-102 3/4x1 2-9/32 1-3/4 17/32 .10836-131 1x3/4 2-1/16 1-13/32 1/4 .07836-2511 2x1-1/2 3-3/32 2-29/32 19/32 .43

1 Outlet sized with bushing

M1

L

N

REINFORCED MALE ADAPTERRmipt x Socket

Part Number Size L M1 N Approx. Wt. (Lbs.)836-005R 1/2 2-3/32 1-5/32 9/16 .05836-007R 3/4 2-1/4 1-3/8 9/16 .08836-010R 1 2-21/32 1-23/32 11/16 .15

M1

NL

NL

M1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (48)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 383 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER BUSHINGFlush StyleSpigot x Socket

Part Number Size L N Approx. Wt. (Lbs.)837-052 3/8x1/4 31/32 5/16 .01

837-072 1/2x1/4 1-3/32 13/32 .02

837-073 1/2x3/8 1-1/8 11/32 .01

837-101 3/4x1/2 1-7/32 11/32 .03

837-1291 1x3/8 1-5/8 27/32 .09

837-130 1x1/2 1-11/32 11/32 .06

837-131 1x3/4 1-11/32 5/16 .04

837-166 1-1/4x1/2 1-1/2 5/8 .12

837-167 1-1/4x3/4 1-1/2 1/2 .10

837-168 1-1/4x1 1-19/32 15/32 .06

837-209 1-1/2x1/2 1-23/32 13/16 .15

837-210 1-1/2x3/4 1-5/8 5/8 .16

837-211 1-1/2x1 1-9/16 13/32 .13

837-212 1-1/2x1-1/4 1-9/16 9/32 .07

837-247 2x1/2 1-25/32 7/8 .24

837-248 2x3/4 1-29/32 21/32 .26

837-249 2x1 1-25/32 5/8 .24

837-250 2x1-1/4 1-11/16 7/16 .20

837-251 2x1-1/2 1-3/4 11/32 .15

837-2871 2-1/2X1/2 2-1/2 1-1/2 .54

837-2881 2-1/2x3/4 2-17/32 1-15/32 .55

837-289 2-1/2x1 2-1/32 29/32 .37

837-290 2-1/2x1-1/4 2-5/32 13/32 .43

837-291 2-1/2x1-1/2 2-5/32 3/4 .37

837-292 2-1/2x2 2-1/16 17/32 .23

837-3341 3x3/4 2-9/16 1-17/32 .69

837-335 3x1 2-9/32 1-1/8 .69

837-336 3x1-1/4 2-1/4 1 .63

837-337 3x1-1/2 2-9/32 7/8 .59

837-338 3x2 2-7/32 23/32 .47

837-339 3x2-1/2 2-7/32 9/16 .471 Outlet sized with bushing

L

PIPE O.D.

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (49)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 384Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER BUSHINGFlush StyleSpigot x Socket

Part Number Size L N Approx. Wt. (Lbs.)837-4151 4x1/2 3-1/16 2-5/32 1.31

837-4161 4x3/4 2-27/32 1-27/32 1.25

837-4171 4x1 3-1/16 1-1/8 1.31

837-4181 4x1-1/4 3-9/16 1-11/16 1.33

837-419 4x1-1/2 2-19/32 1-3/16 1.02

837-420 4x2 2-21/32 1-1/8 1.01

837-421 4x2-1/2 2-17/32 25/32 1.00

837-422 4x3 2-9/16 11/16 .84

837-490 5x4 2-31/32 23/32 1.29

837-490F 5x4 3 3/4 1.41

837-5241 6x3/4 4-1/2 3-1/2 3.45

837-5251 6x1 3-31/32 2-13/16 3.13

837-5261 6x1-1/4 3-25/32 2-17/32 3.07

837-5271 6x1-1/2 3-3/4 2-11/32 3.01

837-528 6x2 3-17/32 2-1/32 2.83

837-5291 6x2-1/2 3-29/32 2-5/32 3.29

837-530 6x3 3-17/32 2-1/8 2.84

837-532 6x4 3-9/16 1-1/4 2.71

837-533F 6x5 3 7/16 1.76

837-534 6x5 3-1/2 7/8 1.93

837-5781 8x2 4-15/16 3-3/8 8.64

837-5801 8x3 5-1/8 3-1/4 8.68

837-582 8x4 4-1/2 2-1/4 5.53

837-585 8x6 4-3/8 1-3/8 5.05

837-6241 10x4 6 3-3/4 10.56

837-626 10x6 5-5/16 2-5/16 9.32

837-628 10x8 5-11/32 1-5/16 9.04

837-666 12x6 7 4 15.51

837-666F 12x6 6-7/16 3-3/8 15.31

837-668 12x8 6-7/8 2-7/16 10.13

837-670 12x10 6-11/32 1-9/32 11.74 1 Outlet sized with bushing

L

PIPE O.D.

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (50)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 385 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER BUSHINGFlush StyleSpigot x Socket

Part Number Size L N Approx. Wt. (Lbs.)837-670F 12x10 6 1 11.04

837-696F 14x6 7-3/4 4-3/4 27.16

837-698F 14x8 7-1/2 3-7/16 32.31

837-700F 14x10 7-7/16 2-7/16 22.30

837-702F 14x12 7 1 9.36

837-756F 16x6 8-3/4 5-3/4 44.23

837-758F 16x8 8-1/2 4-7/16 46.90

837-760F 16x10 8-7/16 3-7/16 39.12

837-762F 16x12 8 2 28.08

837-764F 16x14 8 1 18.37

837-788F 18x8 9-1/2 5-7/16 70.33

837-790F 18x10 9-7/16 4-7/16 65.60

837-792F 18x12 9 3 51.82

837-794F 18x14 9 2 40.70

837-796F 18x16 9 1 32.00

837-818F 20x8 10-1/2 6-7/16 125.96

837-820F 20x10 10-7/16 5-7/16 94.18

837-822F 20x12 10 4 83.14

837-824F 20x14 10 3 73.74

837-826F 20x16 10 2 55.07

837-828F 20x18 10 1 30.35

837-910F 24x10 12-7/16 7-7/16 173.68

837-912F 24x12 12 6 159.41

837-914F 24x14 12 5 80.35

837-916F 24x16 12 4 134.57

837-918F 24x18 12 3 112.54

837-920F 24x20 12 2 79.50

L

PIPE O.D.

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (51)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 386Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER BUSHINGFlush StyleSpigot x Fipt

Part Number Size L N Approx. Wt. (Lbs.)

838-052 3/8x1/4 31/32 3/8 .01

838-071 1/2x1/8 1 9/16 .02

838-072 1/2x1/4 1 7/8 .02

838-073 1/2x3/8 1-3/32 17/32 .02

838-098 3/4x1/4 1-7/32 5/8 .04

838-099 3/4x3/8 1-1/4 21/32 .04

838-101 3/4x1/2 1-1/4 7/16 .03

838-127 1x1/8 1-13/32 29/32 .07

838-128 1x1/4 1-13/32 25/32 .07

838-129 1x3/8 1-13/32 19/32 .07

838-130 1x1/2 1-5/32 21/32 .06

838-131 1x3/4 1-3/8 21/32 .05

838-166 1-1/4x1/2 1-17/32 3/4 .12

838-167 1-1/4x3/4 1-7/16 23/32 .09

838-168 1-1/4x1 1-17/32 5/8 .07

838-206 1-1/2x1/8 1-11/16 1-1/4 .15

838-207 1-1/2x1/4 1-9/16 1-3/16 .13

838-209 1-1/2x1/2 1-11/16 31/32 .17

838-210 1-1/2x3/4 1-9/16 27/32 .13

838-211 1-1/2x1 1-23/32 13/16 .14

838-212 1-1/2x1-1/4 1-1/2 9/16 .07

838-247 2x1/2 1-29/32 1-5/32 .25

838-248 2x3/4 1-7/8 1-5/32 .26

838-249 2x1 1-29/32 1 .25

PIPEO.D.

LN

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (52)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 387 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER BUSHINGFlush StyleSpigot x Fipt

Part Number Size L N Approx. Wt. (Lbs.)

838-250 2x1-1/4 1-19/32 21/32 .18

838-251 2x1-1/2 1-9/16 5/8 .14

838-287 2-1/2x1/2 2-3/8 1-21/32 .41

838-288 2-1/2x3/4 2-7/16 1-5/8 .45

838-289 2-1/2x1 2-5/32 1-1/4 .42

838-290 2-1/2x1-1/4 2-13/32 1-3/8 .42

838-291 2-1/2x1-1/2 2-3/8 1-13/32 .47

838-292 2-1/2x2 2-1/16 1-1/16 .25

838-334 3x3/4 2-9/32 1-1/2 .57

838-335 3x1 2-9/32 1-11/32 .58

838-336 3x1-1/4 2-1/4 1-3/8 .57

838-337 3x1-1/2 2-1/4 1-5/8 .59

838-338 3x2 2-3/16 1-7/32 .63

838-339 3x2-1/2 2-3/8 3/4 .46

838-419 4x1-1/2 3-3/16 2-5/16 1.44

838-420 4x2 2-11/16 1-21/32 1.10

838-421 4x2-1/2 2-21/32 1-1/16 1.08

838-422 4x3 2-5/8 1 .86

838-528 6x2 3-17/32 2-1/2 2.92

838-530 6x3 3-17/32 2-1/8 2.98

838-532 6x4 3-17/32 2-1/32 2.54

PIPEO.D.

LN

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (53)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 388Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCEDREDUCER BUSHINGFlush StyleSpigot x SR Fipt

Part Number Size L N Approx. Wt. (Lbs.)

838-128SR 1x1/4 1-13/32 25/32 .08

838-166SR 1-1/4X1/2 1-7/16 3/4 .11

838-207SR 1-1/2x1/4 1-9/16 1 .13

838-209SR 1-1/2x1/2 1-23/32 31/32 .16

838-210SR 1-1/2x3/4 1-9/16 13/16 .14

838-247SR 2x1/2 1-29/32 1-5/32 .25

838-248SR 2x3/4 1-29/32 1-5/32 .26

838-249SR 2x1 1-7/8 31/32 .26

838-334SR 3x3/4 2-9/32 1-17/32 .58

838-335SR 3x1 2-9/32 1-11/32 .59

838-336SR 3x1-1/4 2-1/4 1-5/16 .57

838-337SR 3x1-1/2 2-1/4 1-3/8 .58

838-528SR 6x2 3-1/2 2-9/16 2.81

838-530SR 6x3 3-17/32 2-1/8 2.94

838-532SR 6x4 3-17/32 2 2.67

REDUCER T.T. BUSHING Flush StyleMipt x Fipt

Part Number Size L N Approx. Wt. (Lbs.)

839-041 1/4x1/8 23/32 11/32 .01

839-052 3/8x1/4 13/16 1/8 .01

L

PIPE O.D.

N

L N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (54)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 389 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCER T.T. BUSHING Flush StyleMipt x Fipt

Part Number Size L N Approx. Wt. (Lbs.)839-072 1/2x1/4 29/32 9/32 .02

839-073 1/2x3/8 15/16 11/32 .01

839-098 3/4x1/4 1-1/32 7/16 .03

839-099 3/4x3/8 1-1/32 7/16 .03

839-101 3/4x1/2 15/16 3/16 .02

839-128 1x1/4 1-1/8 17/32 .05

839-129 1x3/8 1-7/32 5/8 .05

839-130 1x1/2 1-1/16 5/16 .04

839-131 1x3/4 1-1/8 13/32 .04

839-166 1-1/4x1/2 1-5/16 9/16 .10

839-167 1-1/4x3/4 1-9/32 9/16 .08

839-168 1-1/4x1 1-3/16 9/32 .06

839-209 1-1/2x1/2 1-11/32 19/32 .12

839-210 1-1/2x3/4 1-11/32 19/32 .12

839-211 1-1/2x1 1-11/32 13/32 .10

839-212 1-1/2x1-1/4 1-11/32 13/32 .06

839-247 2x1/2 1-3/8 21/32 .17

839-248 2x3/4 1-3/8 5/8 .17

839-249 2x1 1-3/8 15/32 .18

839-250 2x1-1/4 1-3/8 7/16 .16

839-251 2x1-1/2 1-3/8 13/32 .12

839-292 2-1/2x2 1-29/32 7/8 .22

839-337 3x1-1/2 1-15/16 29/32 .49

839-338 3x2 1-15/16 15/16 .45

839-339 3x2-1/2 1-15/16 5/8 .37

839-420 4x2 2-1/8 1-1/8 .83

839-422 4x3 2-1/8 1/2 .71

839-532 6x4 3-17/32 1-13/16 2.53

L N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (55)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 390Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CAP Socket

Part Number Size M W Approx. Wt. (Lbs.)847-002 1/4 13/16 15/16 .01

847-003 3/8 31/32 1-1/8 .02

847-005 1/2 1-3/16 1-7/32 .03

847-007 3/4 1-3/8 1-13/32 .05

847-010 1 1-23/32 1-5/8 .08

847-012 1-1/4 2-3/32 1-27/32 .16

847-015 1-1/2 2-11/32 2 .16

847-020 2 2-7/8 2-1/4 .25

847-025 2-1/2 3-17/32 2-5/8 .48

847-030 3 4-5/32 3-1/32 .70

847-040 4 5-1/4 3-19/32 1.20

847-050F 5 6-1/2 4-7/16 1.83

847-060 6 7-1/2 4-7/8 3.17

SPECIAL REINFORCED REDUCER T.T. BUSHING Mipt x SR Fipt

Part Number Size L N Approx. Wt. (Lbs.)

839-128SR 1x1/4 1-1/8 17/32 .05

839-209SR 1-1/2x1/2 1-11/32 19/32 .13

839-210SR 1-1/2x3/4 1-11/32 19/32 .12

839-247SR 2x1/2 1-3/8 21/32 .18

839-248SR 2x3/4 1-3/8 5/8 .18

839-249SR 2x1 1-3/8 15/32 .19

839-420SR 4x2 2-1/8 1-1/8 .88

LN

W

M

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (56)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 391 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CAP Fipt

Part Number Size M W Approx. Wt. (Lbs.)848-002 1/4 29/32 15/16 .02848-003 3/8 31/32 29/32 .02848-005 1/2 1-3/16 1-1/16 .04848-007 3/4 1-3/32 1-7/32 .04848-010 1 1-27/32 1-7/16 .10848-012 1-1/4 2-7/32 1-17/32 .15 848-015 1-1/2 2-17/32 1-5/8 .19848-020 2 3-5/32 1-25/32 .29848-025 2-1/2 3-5/8 2-7/16 .54848-030 3 4-3/8 2-7/16 .90848-040 4 5-7/16 3-1/16 1.32

848-060F 6 7-3/16 4-3/8 2.07848-080F 8 9-3/8 4-3/8 3.62848-100F 10 11-5/8 5-3/4 7.44848-120F 12 13-13/16 6-3/16 10.77

CAP Socket

Part NumberSize M W

Approx. Wt. (Lbs.)PVC PVC

847-080 8 9-23/32 6-3/8 6.10

847-100F 10 12-1/4 5-15/16 8.26

847-120F 12 14-1/4 7-1/8 11.30

847-140F 14 15-1/2 7-3/8 14.65

847-160F 16 17-7/8 9 23.44

847-180F 18 19-15/16 9-1/4 28.88

847-200F 20 22 14-1/4 49.05

847-240F 24 26-3/8 17-1/4 89.38

W

M

M

W

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (57)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 392Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PLUG Spigot

Part Number Size L Approx. Wt. (Lbs.)

849-005 1/2 1-1/8 .02

849-007 3/4 1-1/4 .03

849-010 1 1-3/8 .06

849-012 1-1/4 1-17/32 .10

849-015 1-1/2 1-11/16 .13

849-020 2 1-7/8 .21

849-025F 2-1/2 5-3/8 1.10

849-030F 3 5-5/8 1.63

849-040F 4 6-1/2 2.76

849-060F 6 9 6.71

849-080F 8 12 12.73

849-100F 10 11-15/16 17.99

849-120F 12 14-1/8 26.34

SPECIAL REINFORCED CAP SR Fipt

Part Number Size M W Approx. Wt. (Lbs.)

848-002SR 1/4 27/32 27/32 .02

848-003SR 3/8 31/32 29/32 .03

848-005SR 1/2 1-3/16 1-1/8 .04

848-007SR 3/4 1-3/8 1-3/32 .05

848-030SR 3 4-9/32 2-7/16 .79

M

W

PIPE O.D.

L

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (58)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 393 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PLUG Mipt

L

Part Number Size L Approx. Wt. (Lbs.)850-002 1/4 23/32 .01

850-003 3/8 13/16 .01

850-005 1/2 13/16 .02

850-007 3/4 7/8 .02

850-010 1 1-1/4 .06

850-012 1-1/4 1-9/32 .08

850-015 1-1/2 1-11/32 .10

850-020 2 1-3/8 .15

850-025 2-1/2 1-25/32 .30

850-030 3 1-7/8 .43

850-040 4 2-3/32 .77

850-060 6 2-3/32 1.73

850-080F 8 8-5/8 11.45

850-100F 10 8-7/16 12.91

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (59)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 394Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

WYESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

875-005 1/2 1/4 1-5/32 1-5/32 1-1/8 2-1/16 2-1/32 3-3/16 1-5/32 1-5/32 .12

875-007 3/4 5/16 1-3/8 1-3/8 1-5/16 2-3/8 2-3/8 3-23/32 1-3/8 1-3/8 .19

875-010 1 5/16 1-3/4 1-3/4 1-7/16 2-29/32 2-7/8 4-11/32 1-11/16 1-11/16 .31

875-012 1-1/4 13/32 2-5/32 2-5/32 1-21/32 3-13/32 3-13/32 5-3/32 2-1/16 2-1/16 .50

875-015 1-1/2 17/32 2-1/2 2-1/2 1-29/32 3-7/8 3-7/8 5-13/16 2-5/16 2-5/16 .70

875-020 2 5/8 3-7/32 3-7/32 2-5/32 4-7/8 4-7/8 6-7/8 2-7/8 2-7/8 1.20

875-025 2-1/2 27/32 3-31/32 3-31/32 2-19/32 5-23/32 5-23/32 8-5/16 3-1/2 3-1/2 2.00

875-030 3 31/32 4-3/4 4-25/32 2-27/32 6-5/8 6-21/32 9-1/2 4-3/16 4-3/16 3.02

875-040 4 1-1/4 6-1/32 6-1/32 3-1/2 8-9/32 8-9/32 11-25/32 5-1/4 5-1/4 5.10

875-050F 5 5-1/8 10-11/16 10-11/16 8-1/8 13-11/16 13-11/16 21-13/16 6-5/16 6-5/16 9.34

875-060 6 1-5/32 8-25/32 8-3/16 4-3/16 11-25/32 11-3/16 15-3/8 7-9/16 7-9/16 12.01

875-080 8 1-15/16 11-11/32 11-11/32 5-31/32 15-11/32 15-11/32 21-5/16 9-3/4 9-3/4 25.44

875-080F 8 5-1/16 15-7/8 13-11/16 9-5/16 20-1/8 17-15/16 27-1/4 9-5/8 9-5/8 39.76

875-100F 10 6-1/2 18-7/8 17-1/4 11-3/4 24-1/8 22-1/2 34-1/4 11-15/16 11-15/16 65.51

875-120F 12 7-1/8 21-13/16 19-7/8 13-3/8 28-1/16 26-1/8 39-1/2 14-1/8 14-1/8 109.85

875-140F 14 9-13/16 23-13/16 23-13/16 16-13/16 30-13/16 30-13/16 47-5/8 15-1/2 15-1/2 135.75

875-160F 16 10-1/8 26-1/8 26-1/8 18-1/8 34-1/8 34-1/8 52-1/4 17-11/16 17-11/16 183.59

875-180F 18 10 29-3/8 28 19 38-3/8 37 56 19-7/8 19-7/8 255.49

875-200F 20 11-5/8 31-5/8 31-5/8 21-5/8 41-5/8 41-5/8 63-1/4 22-1/16 22-1/16 399.60

875-240F 24 14-1/4 38-1/4 38-1/4 26-1/4 50-1/4 50-1/4 76-1/2 26-7/16 26-7/16 617.50

1 Outlet sized with bushing

1/2" - 2" 235 psi @ 73°F2-1/2" - 6" 150 psi @ 73°F

8" & Up & All Fab 100 psi @ 73°F

H1 G1

M

G G2 H2 H

L

M1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (60)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 395 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING WYESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

875-1311 1x1x3/4 1/4 2-7/32 1-27/32 1-3/8 2-31/32 2-31/32 4-11/32 1-11/16 1-11/16 .35

875-1671 1-1/4x1-1/4x3/4 3/8 2-3/4 2-1/4 1-5/8 3-3/4 3-1/2 5-1/8 2-1/16 2-1/16 .61

875-1681 1-1/4x1-1/4x1 3/8 2-5/8 2-1/4 1-5/8 3-3/4 3-1/2 5-1/8 2-1/16 2-1/16 .56

875-2101 1-1/2x1-1/2x3/4 1/2 3-1/2 2-9/16 1-7/8 4-1/2 3-15/16 5-13/16 2-11/32 2-11/32 .88

875-2111 1-1/2x1-1/2x1 1/2 3 2-9/16 1-7/8 4-5/32 3-15/16 5-13/16 2-11/32 2-11/32 .83

875-2121 1-1/2x1-1/2x1-1/4 1/2 3-1/4 2-9/16 1-7/8 4-1/2 3-15/16 5-13/16 2-11/32 2-11/32 .74

875-2481 2x2x3/4 5/8 4-5/32 3-7/32 2-5/32 5-5/32 4-7/8 6-7/8 2-7/8 2-7/8 1.46

875-2501 2x2x1-1/4 5/8 3-5/16 3-3/8 2-5/32 5 4-3/4 6-7/8 2-7/8 2-7/8 1.46

875-2911 2-1/2x2-1/2x1-1/2 1 6-1/4 4-9/16 3-1/16 7-5/8 6-5/8 9-11/16 4-3/16 4-3/16 4.34

875-2921 2-1/2x2-1/2x2 1/2 3-3/4 4-3/4 2-1/2 6-7/8 6-1/2 9-3/8 4-1/4 4-1/4 3.97

875-3351 3x3x1 11/16 5-7/8 4-7/32 2-9/16 6-15/16 6-1/8 8-23/32 4-3/16 4-3/16 3.27

875-3361 3x3x1-1/4 7/8 5-3/4 4-1/8 2-3/4 7 6 8-3/4 4-3/16 4-3/16 3.21

875-3371 3x3x1-1/2 2-5/8 5-1/2 4-1/4 2-5/8 6-7/8 6-1/8 8-3/4 4-3/16 4-3/16 3.14

875-3381 3x3x2 1 5-11/32 4-3/4 2-7/8 6-31/32 6-5/8 9-1/2 4-3/16 4-3/16 3.48

875-3391 3x3x2-1/2 7/8 4-1/8 4-21/32 2-3/4 6-3/4 6 8-3/4 4-3/16 4-3/16 2.97

875-4191 4x4x1-1/2 1 6-5/8 5-1/4 3-1/4 8-13/16 7-1/2 10-3/4 5-1/4 5-3/16 6.04

875-420 4x4x2 –7/8 5-5/32 4-11/16 1-3/8 6-11/16 6-15/16 8-5/16 5-9/32 2-29/32 2.78

875-421F 4x4x2-1/2 4-9/16 8-13/16 9-1/16 6-13/16 10-1/2 11-5/16 18-1/8 5-1/4 3-1/2 5.37

875-422 4x4x3 1/2 5-7/16 5-7/32 2-3/4 7-5/16 7-15/32 10-7/32 5-1/4 4-3/16 3.98

875-5281 6x6x2 1/16 8-13/16 6-9/16 3-1/16 10-5/16 9-9/16 12-5/8 7-9/16 5-7/16 9.78

875-528F 6x6x2 1-15/16 9-3/16 8-9/16 5-3/16 10-15/16 11-13/16 17 7-1/2 2-13/16 9.36

875-5301 6x6x3 -1/16 8-3/8 6-11/16 3 10-1/4 9-11/16 12-5/8 7-9/16 5-3/8 9.60

875-530F 6x6x3 2-15/16 10-5/16 9-9/16 6-3/16 12-9/16 12-13/16 19 7-1/2 4-1/8 13.92

875-532 6x6x4 31/32 6-9/16 5-11/16 3-15/16 8-27/32 8-23/32 12-21/32 7-9/16 5-7/16 8.61

875-5781 8x8x2 2 14-15/16 11-1/4 6 16-9/16 16-7/16 21-1/4 9-11/16 9-11/16 34.05

875-578F 8x8x2 7/8 10-1/2 9-1/2 5-1/8 12-1/4 13-3/4 18-7/8 9-5/8 2-13/16 17.93

875-579F 8x8x2-1/2 1-7/16 10-15/16 10-1/16 5-11/16 12-15/16 14-5/16 20 9-5/8 3-7/16 21.92

875-580F 8x8x3 1-15/16 11-5/8 10-9/16 6-3/16 13-7/8 14-13/16 21 9-5/8 4-1/8 21.92

875-582 8x8x4 11/16 9-1/8 8-1/4 3-5/16 11-3/8 12-1/4 15-9/16 9-3/4 5-1/4 14.60

875-582F 8x8x4 2-15/16 11-7/8 11-9/16 7-3/16 14-1/8 15-13/16 23 9-5/8 5-3/16 18.50

875-5851 8x8x6 2 12-15/16 11-1/4 6 15-15/16 15-1/4 21-1/4 9-11/16 9-11/16 30.74

875-585F 8x8x6 4-15/16 13-15/16 13-9/16 9-3/16 17-3/16 17-13/16 27 9-5/8 7-1/2 32.97

875-6211 10x10x2 3-3/4 6 14-1/2 9 17-1/2 19-3/4 28-3/4 11 7-1/2 30.84 1 Outlet sized with bushing

1/2" - 2-1/2" 235 psi @ 73°F3" - 6" 150 psi @ 73°F

8" & Up & All Fab 100 psi @ 73°F M

M1

G G2

LH

H1G1

H2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (61)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 396Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING WYESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

875-621F 10x10x2 1/4 11-7/8 10-1/2 5 13-5/8 15-3/4 20-3/4 11-15/16 2-13/16 41.46875-622F 10x10x2-1/2 1/8 12-5/16 10-7/8 5-3/8 14-5/16 16-1/8 21-1/2 11-15/16 3-7/16 29.34875-6231 10x10x3 7/8 12-7/8 11-5/8 6-1/8 15-1/4 16-7/8 23 12 4-1/8 30.70

875-623F 10x10x3 3/4 13 11-1/2 6 15-1/4 16-3/4 22-3/4 11-15/16 4-1/8 31.71875-6241 10x10x4 1-7/8 10-5/8 12-5/8 7-1/8 12-1/4 17-7/8 25 12 5-3/8 30.56875-624F 10x10x4 1-3/4 13-1/4 12-1/2 7 15-1/2 17-3/4 24-3/4 11-15/16 5-3/16 39.93875-626 10x10x6 -3/16 12 11 4-13/16 15 16 20-25/32 12-1/16 7-21/32 28.21

875-626F 10x10x6 3-3/4 15-5/16 14-1/2 9 18-9/16 19-3/4 28-3/4 11-15/16 7-1/2 42.69875-628 10x10x8 1-7/32 12-3/4 12-1/4 6-7/32 16-25/32 17-9/32 23-1/2 12-1/32 9-23/32 34.14

875-628F 10x10x8 5-1/4 17-1/4 16 10-1/2 21-1/2 21-1/4 31-3/4 11-15/16 9-5/8 55.19875-661F 12x12x2 1-5/16 13-3/16 11-7/16 4-15/16 14-15/16 17-11/16 22-5/8 14-1/8 2-13/16 37.58875-662F 12x12x2-1/2 15/16 13-5/8 11-13/16 5-5/16 15-5/8 18-1/16 23-3/8 14-1/8 3-7/16 43.72875-663F 12x12x3 1/8 14-5/16 12-7/8 6-3/8 16-9/16 19-1/8 25-1/2 14-1/8 4-1/8 43.39875-664F 12x12x4 5/8 14-9/16 13-3/8 6-7/8 16-13/16 19-5/8 26-1/2 14-1/8 5-3/16 48.41875-666F 12x12x6 2-5/8 16-5/8 15-3/8 8-7/8 19-7/8 21-5/8 30-1/2 14-1/8 7-1/2 64.52875-668F 12x12x8 4-1/4 18-9/16 17 10-1/2 22-13/16 23-1/4 33-3/4 14-1/8 9-5/8 71.04875-670F 12x12x10 5-3/4 20-3/16 18-1/2 12 25-7/16 24-3/4 36-3/4 14-1/8 11-15/16 80.79875-694F 14x14x4 1-1/4 15-5/16 15-1/4 8-1/4 17-9/16 22-1/4 30-1/2 15-1/2 5-3/16 68.80875-696F 14x14x6 2 17-3/8 16 9 20-5/8 23 32 15-1/2 7-1/2 78.50875-698F 14x14x8 4-1/4 19-5/16 18-1/4 11-1/4 23-9/16 25-1/4 36-1/2 15-1/2 9-5/8 90.50875-700F 14x14x10 5-3/4 20-15/16 19-3/4 12-3/4 26-3/16 26-3/4 39-1/2 15-1/2 11-15/16 84.58875-702F 14x14x12 7-1/4 22-9/16 21-1/4 14-1/4 28-13/16 28-1/4 42-1/2 15-1/2 14-1/8 108.22875-754F 16x16x4 1-1/8 16-5/8 17-1/8 9-1/8 18-7/8 25-1/8 34-1/4 17-11/16 5-3/16 76.47875-756F 16x16x6 1-5/8 18-11/16 17-5/8 9-5/8 21-15/16 25-5/8 35-1/4 17-11/16 7-1/2 105.73875-758F 16x16x8 3-5/8 20-5/8 19-5/8 11-5/8 24-7/8 27-5/8 39-1/4 17-11/16 9-5/8 120.00875-760F 16x16x10 5-1/8 22-1/4 21-1/8 13-1/8 27-1/2 29-1/8 42-1/4 17-11/16 11-15/16 123.77875-762F 16x16x12 6-1/2 23-7/8 22-1/2 14-1/2 30-1/8 30-1/2 45 17-11/16 14-1/8 142.80875-764F 16x16x14 7-7/8 25-1/8 23-7/8 15-7/8 32-1/8 31-7/8 47-3/4 17-11/16 15-1/2 161.25875-784F 18x18x4 0 17-7/8 18 9 20-1/8 27 36 19-7/8 5-3/16 116.63875-786F 18x18x6 3/8 20-1/8 18-9/16 9-3/8 23-3/8 27-9/16 36-15/16 19-7/8 7-1/2 114.13875-788F 18x18x8 3 21-7/8 21 12 26-1/8 30 42 19-7/8 9-5/8 92.20875-790F 18x18x10 4-1/2 23-1/2 22-1/2 13-1/2 28-3/4 31-1/2 45 19-7/8 11-15/16 164.27875-792F 18x18x12 6 25-1/8 24 15 31-3/8 33 48 19-7/8 14-1/8 184.56875-794F 18x18x14 7 26-3/8 25 16 33-3/8 34 50 19-7/8 15-1/2 225.00875-796F 18x18x16 8-1/2 27-3/8 26-1/2 17-1/2 35-3/8 35-1/2 53 19-7/8 17-11/16 225.00875-814F 20x20x4 1 19-3/16 19 9 21-7/16 29 38 22-1/16 5-3/16 142.64875-816F 20x20x6 1/8 21-1/4 19-7/8 9-7/8 24-1/2 29-7/8 39-3/4 22-1/16 7-1/2 156.65

1 Outlet sized with bushing

1/2" - 2-1/2" 235 psi @ 73°F3" - 6" 150 psi @ 73°F

8" & Up & All Fab 100 psi @ 73°F M

M1

G G2

LH

H1G1

H2

REDUCING WYESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

875-621F 10x10x2 1/4 11-7/8 10-1/2 5 13-5/8 15-3/4 20-3/4 11-15/16 2-13/16 41.46875-622F 10x10x2-1/2 1/8 12-5/16 10-7/8 5-3/8 14-5/16 16-1/8 21-1/2 11-15/16 3-7/16 29.34875-6231 10x10x3 7/8 12-7/8 11-5/8 6-1/8 15-1/4 16-7/8 23 12 4-1/8 30.70

875-623F 10x10x3 3/4 13 11-1/2 6 15-1/4 16-3/4 22-3/4 11-15/16 4-1/8 31.71875-6241 10x10x4 1-7/8 10-5/8 12-5/8 7-1/8 12-1/4 17-7/8 25 12 5-3/8 30.56875-624F 10x10x4 1-3/4 13-1/4 12-1/2 7 15-1/2 17-3/4 24-3/4 11-15/16 5-3/16 39.93875-626 10x10x6 -3/16 12 11 4-13/16 15 16 20-25/32 12-1/16 7-21/32 28.21

875-626F 10x10x6 3-3/4 15-5/16 14-1/2 9 18-9/16 19-3/4 28-3/4 11-15/16 7-1/2 42.69875-628 10x10x8 1-7/32 12-3/4 12-1/4 6-7/32 16-25/32 17-9/32 23-1/2 12-1/32 9-23/32 34.14

875-628F 10x10x8 5-1/4 17-1/4 16 10-1/2 21-1/2 21-1/4 31-3/4 11-15/16 9-5/8 55.19875-661F 12x12x2 1-5/16 13-3/16 11-7/16 4-15/16 14-15/16 17-11/16 22-5/8 14-1/8 2-13/16 37.58875-662F 12x12x2-1/2 15/16 13-5/8 11-13/16 5-5/16 15-5/8 18-1/16 23-3/8 14-1/8 3-7/16 43.72875-663F 12x12x3 1/8 14-5/16 12-7/8 6-3/8 16-9/16 19-1/8 25-1/2 14-1/8 4-1/8 43.39875-664F 12x12x4 5/8 14-9/16 13-3/8 6-7/8 16-13/16 19-5/8 26-1/2 14-1/8 5-3/16 48.41875-666F 12x12x6 2-5/8 16-5/8 15-3/8 8-7/8 19-7/8 21-5/8 30-1/2 14-1/8 7-1/2 64.52875-668F 12x12x8 4-1/4 18-9/16 17 10-1/2 22-13/16 23-1/4 33-3/4 14-1/8 9-5/8 71.04875-670F 12x12x10 5-3/4 20-3/16 18-1/2 12 25-7/16 24-3/4 36-3/4 14-1/8 11-15/16 80.79875-694F 14x14x4 1-1/4 15-5/16 15-1/4 8-1/4 17-9/16 22-1/4 30-1/2 15-1/2 5-3/16 68.80875-696F 14x14x6 2 17-3/8 16 9 20-5/8 23 32 15-1/2 7-1/2 78.50875-698F 14x14x8 4-1/4 19-5/16 18-1/4 11-1/4 23-9/16 25-1/4 36-1/2 15-1/2 9-5/8 90.50875-700F 14x14x10 5-3/4 20-15/16 19-3/4 12-3/4 26-3/16 26-3/4 39-1/2 15-1/2 11-15/16 84.58875-702F 14x14x12 7-1/4 22-9/16 21-1/4 14-1/4 28-13/16 28-1/4 42-1/2 15-1/2 14-1/8 108.22875-754F 16x16x4 1-1/8 16-5/8 17-1/8 9-1/8 18-7/8 25-1/8 34-1/4 17-11/16 5-3/16 76.47875-756F 16x16x6 1-5/8 18-11/16 17-5/8 9-5/8 21-15/16 25-5/8 35-1/4 17-11/16 7-1/2 105.73875-758F 16x16x8 3-5/8 20-5/8 19-5/8 11-5/8 24-7/8 27-5/8 39-1/4 17-11/16 9-5/8 120.00875-760F 16x16x10 5-1/8 22-1/4 21-1/8 13-1/8 27-1/2 29-1/8 42-1/4 17-11/16 11-15/16 123.77875-762F 16x16x12 6-1/2 23-7/8 22-1/2 14-1/2 30-1/8 30-1/2 45 17-11/16 14-1/8 142.80875-764F 16x16x14 7-7/8 25-1/8 23-7/8 15-7/8 32-1/8 31-7/8 47-3/4 17-11/16 15-1/2 161.25875-784F 18x18x4 0 17-7/8 18 9 20-1/8 27 36 19-7/8 5-3/16 116.63875-786F 18x18x6 3/8 20-1/8 18-9/16 9-3/8 23-3/8 27-9/16 36-15/16 19-7/8 7-1/2 114.13875-788F 18x18x8 3 21-7/8 21 12 26-1/8 30 42 19-7/8 9-5/8 92.20875-790F 18x18x10 4-1/2 23-1/2 22-1/2 13-1/2 28-3/4 31-1/2 45 19-7/8 11-15/16 164.27875-792F 18x18x12 6 25-1/8 24 15 31-3/8 33 48 19-7/8 14-1/8 184.56875-794F 18x18x14 7 26-3/8 25 16 33-3/8 34 50 19-7/8 15-1/2 225.00875-796F 18x18x16 8-1/2 27-3/8 26-1/2 17-1/2 35-3/8 35-1/2 53 19-7/8 17-11/16 225.00875-814F 20x20x4 1 19-3/16 19 9 21-7/16 29 38 22-1/16 5-3/16 142.64875-816F 20x20x6 1/8 21-1/4 19-7/8 9-7/8 24-1/2 29-7/8 39-3/4 22-1/16 7-1/2 156.65

1 Outlet sized with bushing

1/2" - 2-1/2" 235 psi @ 73°F3" - 6" 150 psi @ 73°F

8" & Up & All Fab 100 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (62)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Page 397 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING WYESocket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

875-816F 20x20x6 1/8 21-1/4 19-7/8 9-7/8 24-1/2 29-7/8 39-3/4 22-1/16 7-1/2 156.65875-818F 20x20x8 2-5/8 23-3/16 22-5/8 12-5/8 27-7/16 32-5/8 45-1/4 22-1/16 9-5/8 173.00875-820F 20x20x10 4-1/8 24-13/16 24-1/8 14-1/8 30-1/16 34-1/8 48-1/4 22-1/16 11-15/16 190.74875-822F 20x20x12 5-5/8 26-7/16 25-5/8 15-5/8 32-11/16 35-5/8 51-1/4 22-1/16 14-1/8 237.50875-824F 20x20x14 7-1/8 27-11/16 27-1/8 17-1/8 34-11/16 37-1/8 54-1/4 22-1/16 15-1/2 243.75875-826F 20x20x16 8-1/2 28-11/16 28-1/2 18-1/2 36-11/16 38-1/2 57 22-1/16 17-11/16 250.00875-828F 20x20x18 10-1/8 30-11/16 30-1/8 20-1/8 39-11/16 40-1/8 60-1/4 22-1/16 19-7/8 255.62875-904F 24x24x4 3 21-3/4 21 9 24 33 42 26-7/16 5-3/16 230.78875-906F 24x24x6 7/8 23-13/16 23-1/8 11-1/8 27-1/16 35-1/8 46-1/4 26-7/16 7-1/2 248.89875-908F 24x24x8 1-3/4 25-3/4 25-3/4 13-3/4 30 37-3/4 51-1/2 26-7/16 9-5/8 269.27875-910F 24x24x10 3-1/4 27-3/8 27-1/4 15-1/4 32-5/8 39-1/4 54-1/2 26-7/16 11-15/16 291.66875-912F 24x24x12 4-3/4 29 28-3/4 16-3/4 35-1/4 40-3/4 57-1/2 26-7/16 14-1/8 264.99875-914F 24x24x14 6-1/4 30-1/4 30-1/4 18-1/4 37-1/4 42-1/4 60-1/2 26-7/16 15-1/2 283.70875-916F 24x24x16 7-3/4 31-1/4 31-3/4 19-3/4 39-1/4 43-3/4 63-1/2 26-7/16 17-11/16 310.60875-918F 24x24x18 9-1/4 33-1/4 33-1/4 21-1/4 42-1/4 45-1/4 66-1/2 26-7/16 19-7/8 255.60875-920F 24x24x20 9-5/8 34-3/16 33-5/8 21-5/8 44-3/16 45-5/8 67-1/4 26-7/16 22-1/16 372.56

1/2" - 2-1/2" 235 psi @ 73°F3" - 6" 150 psi @ 73°F

8" & Up & All Fab 100 psi @ 73°F

DOUBLE WYESocket x Socket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

876-020F 2 3-7/8 6-1/4 6-1/4 5-7/16 7-13/16 7-13/16 13-3/16 2-7/8 2-7/8 2.97876-030F 3 4-3/4 8-1/4 8-1/4 6-5/8 10-3/16 10-3/16 16-13/16 4-3/16 4-3/16 6.48876-040F 4 4-11/16 9-3/16 9-3/16 6-15/16 11-7/16 11-7/16 18-3/8 5-3/16 5-3/16 9.74876-060F 6 4-15/16 12-5/8 11-9/16 8-3/16 15-7/8 14-13/16 23 7-1/2 7-1/2 25.44876-080F 8 5-1/16 15-7/8 13-11/16 9-5/16 20-1/8 17-15/16 27-1/4 9-5/8 9-5/8 48.35876-100F 10 6-1/2 18-7/8 17-1/4 11-3/4 24-1/8 22-1/2 34-1/4 11-15/16 11-15/16 65.51876-120F 12 7-1/8 21-13/16 19-7/8 13-3/8 28-1/16 26-1/8 39-1/2 14-1/8 14-1/8 101.98

100 psi @ 73°F

M1

LH2

G2

GH

M

G1H1

M

M1

G G2

LH

H1G1

H2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (63)

Schedule 80 PVC Technical Information

Schedule 80 Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 398Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

REDUCING DOUBLE WYESocket x Socket x Socket x Socket

Part Number Size G G1 G2 H H1 H2 L M M1 Approx. Wt. (Lbs.)

876-338 3x2 3/8 4-1/4 4-13/32 2-1/4 5-3/4 5-29/32 8 4-3/16 2-7/8 2.24

876-421F 4x2-1/2 4-9/16 8-13/16 9-1/16 6-13/16 10-1/2 11-5/16 18-1/8 5-1/4 3-1/2 5.37

876-422F 4x3 4-11/16 10 9-3/16 6-15/16 11-13/16 11-7/16 18-3/8 5-3/16 5-3/16 13.87

876-528F 6x2 1-15/16 9-3/16 8-9/16 5-3/16 10-15/16 11-13/16 17 7-1/2 2-13/16 10.07

876-529F 6x2-1/2 2-7/16 9-5/8 9-1/16 5-11/16 11-5/8 12-5/16 18 7-1/2 3-7/16 13.21

876-530F 6x3 2-15/16 10-15/16 9-9/16 6-3/16 12-9/16 12-13/16 19 7-1/2 4-1/8 13.21

876-532F 6x4 3-15/16 10-9/16 10-9/16 7-3/16 12-13/16 13-13/16 21 7-1/2 5-3/16 18.77

876-578F 8x2 7/8 10-1/2 9-1/2 5-1/8 12-1/4 13-3/4 18-7/8 9-5/8 2-13/16 14.55

876-579F 8x2-1/2 1-7/16 10-15/16 10-1/16 5-11/16 12-15/16 14-5/16 20 9-5/8 3-7/16 21.92

876-580F 8x3 1-15/16 11-5/8 10-9/16 6-3/16 13-7/8 14-13/16 21 9-5/8 4-1/8 18.87

876-582F 8x4 2-15/16 11-7/8 11-9/16 7-3/16 14-1/8 15-13/16 23 9-5/8 5-3/16 20.88

876-585F 8x6 4-15/16 13-15/16 13-9/16 9-3/16 17-3/16 17-13/16 27 9-5/8 7-1/2 28.76

876-621F 10x2 1/4 11-7/8 10-1/2 5 13-5/8 15-3/4 20-3/4 11-15/16 2-13/16 26.48

876-622F 10x2-1/2 1/8 12-5/16 10-7/8 5-3/8 14-5/16 16-1/8 21-1/2 11-15/16 3-7/16 29.34

876-623F 10x3 3/4 13 11-1/2 6 15-1/4 16-3/4 22-3/4 11-15/16 4-1/8 22.67

876-624F 10x4 1-3/4 13-1/4 12-1/2 7 15-1/2 17-3/4 24-3/4 11-15/16 5-3/16 30.53

876-626F 10x6 3-3/4 15-5/16 14-1/2 9 18-9/16 19-3/4 28-3/4 11-15/16 7-1/2 40.05

876-628F 10x8 5-1/4 17-1/4 16 10-1/2 21-1/2 21-1/4 31-3/4 11-15/16 9-5/8 55.99

876-661F 12x2 1-5/16 13-3/16 11-7/16 4-15/16 14-15/16 17-11/16 22-5/8 14-1/8 2-13/16 37.58

876-662F 12x2-1/2 15/16 13-5/8 11-13/16 5-5/16 15-5/8 18-1/16 23-3/8 14-1/8 3-7/16 44.74

876-663F 12x3 1/8 14-5/16 12-7/8 6-3/8 16-9/16 19-1/8 25-1/2 14-1/8 4-1/8 43.39

876-664F 12x4 5/8 14-9/16 13-3/8 6-7/8 16-13/16 19-5/8 26-1/2 14-1/8 5-3/16 40.74

876-666F 12x6 2-5/8 16-5/8 15-3/8 8-7/8 19-7/8 21-5/8 30-1/2 14-1/8 7-1/2 68.02

876-668F 12x8 4-1/4 18-9/16 17 10-1/2 22-13/16 23-1/4 33-3/4 14-1/8 9-5/8 71.03

876-670F 12x10 5-3/4 20-3/16 18-1/2 12 25-7/16 24-3/4 36-3/4 14-1/8 11-15/16 80.79

3" - 6" 150 psi @ 73°FAll Fab 100 psi @ 73°F

H1G1 M1

H2L

G2

M

GH

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (64)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 399 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

UNION (Old Style)Socket x Socket Dimensions Also Applicable to897-XXX EPDM O-ring Seal Units

N L

NUT O.D. M

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)857-002 1/4 1-15/16 15/16 5/8 1-21/32 .09

857-003 3/8 2-5/32 1-1/32 19/32 1-25/32 .11

857-005 1/2 2-3/32 1-9/32 11/32 1-31/32 .15

857-007 3/4 2-3/8 1-17/32 11/32 2-1/2 .26

857-010 1 2-9/16 1-27/32 3/8 2-7/8 .37

857-012 1-1/4 2-7/8 2-7/32 3/8 3-5/16 .50

857-015 1-1/2 3-3/32 2-9/16 15/32 3-9/16 .60

857-020 2 3-5/8 3-1/32 9/16 4-3/16 .96

857-025 2-1/2 4-3/8 3-5/8 15/16 4-7/8 1.51

857-030 3 5-1/16 4-3/8 1-3/16 5-3/4 2.33

857-040 4 5-7/8 5-13/32 1-3/8 7-1/16 3.74

235 psi @ 73°F

1) For (Socket X Socket) Unions Equipped With EPDM O-ring, Replace The 857 With An 897 Before The Dash. e.g. Part Number 897-002 = 1/4" PVC, Union, Socket x Socket, With EPDM O-rings.

UNION (Old Style)Fipt x Fipt Dimensions Also Applicable to 898-XXX EPDM O-ring Seal Units

L N

MNUT O.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)858-002 1/4 1-15/16 15/16 11/16 1-21/32 .10

858-003 3/8 2-5/32 1-1/32 15/16 1-25/32 .12

858-005 1/2 2-3/32 1-9/32 19/32 1-31/32 .16

858-007 3/4 2-3/8 1-17/32 3/4 2-1/2 .28

235 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (65)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 400Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

1) For (Fipt X Fipt) Unions Equipped With EPDM O-ring, Replace The 858 With An 898 Before The Dash. e.g. Part Number 898-002 = 1/4" PVC, Union, Fipt x Fipt, With EPDM O-rings.

UNION (Old Style)Socket x Fipt Dimensions Also Applicable to 899-XXX EPDM O-ring Seal Units

MNUT O.D.

NL

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)859-002 1/4 1-15/16 15/16 21/32 1-21/32 .08

859-003 3/8 2-5/32 1-1/32 3/4 1-25/32 .10

859-005 1/2 2-3/32 1-9/32 15/32 1-31/32 .16

859-007 3/4 2-3/8 1-17/32 9/16 2-1/2 .27

859-010 1 2-9/16 1-27/32 13/32 2-7/8 .38

859-012 1-1/4 2-7/8 2-7/32 5/8 3-5/16 .52

859-015 1-1/2 3-1/8 2-19/32 27/32 3-9/16 .63

235 psi @ 73°F

235 psi @ 73°F

UNION (Old Style)Fipt x Fipt Dimensions Also Applicable to 898-XXX EPDM O-ring Seal Units

L N

MNUT O.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)858-010 1 2-9/16 1-27/32 7/16 2-7/8 .39

858-012 1-1/4 2-7/8 2-7/32 7/8 3-5/16 .56

858-015 1-1/2 3-3/32 2-9/16 1-5/32 3-9/16 .65

858-020 2 3-5/8 3-1/32 1-11/16 4-3/16 1.05

858-025 2-1/2 4-3/8 3-5/8 1-7/8 4-7/8 1.67

858-030 3 5-1/16 4-3/8 1-13/16 5-3/4 2.51

858-040 4 5-7/8 5-7/16 2-3/8 7-1/16 4.07

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (66)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 401 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TRANSITION UNIONSocket x Brass Fipt Threaded Insert and FKM O-ring SealDimensions Also Applicable to 899-XXXBR EPDM O-ring Seal Units

L N

MNUTO.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)859-005BR 1/2 2-1/4 1-9/32 3/4 1-31/32 .21859-007BR 3/4 2-11/16 1-17/32 15/16 2-1/2 .35859-010BR 1 2-13/16 1-7/8 1-1/32 2-7/8 .52859-012BR 1-1/4 3-9/32 2-7/32 1-1/16 3-5/16 .69859-015BR 1-1/2 3-1/2 2-9/16 1-3/32 3-17/32 .89859-020BR 2 3-5/8 2-7/8 1-1/4 4-5/16 1.60

Not intended to convey or dispense water for human consumption through drinking or cooking

1) For (Socket X Metal Fipt) Unions Equipped With EPDM O-ring, Replace The 859 With An 899 Before The Dash. e.g. Part Number 899-010BR = 1" PVC, Union Socket x Metal Fipt With EPDM O-rings.

235 psi @ 73°F

1) For (Socket X Fipt) Unions Equipped With EPDM O-ring, Replace The 859 With An 899 Before The Dash. e.g. Part Number 899-002 = 1/4" PVC, Union, Socket x Fipt, With EPDM O-rings.

UNION (Old Style)Socket x Fipt Dimensions Also Applicable to 899-XXX EPDM O-ring Seal Units

MNUT O.D.

NL

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D.Approx. Wt.

(Lbs.)859-020 2 3-5/8 3-1/32 1-1/16 4-3/16 1.00

859-025 2-1/2 4-3/8 3-5/8 1-13/32 4-7/8 1.58

859-030 3 5-1/16 4-3/8 1-1/2 5-3/4 2.42

859-040 4 5-7/8 5-7/16 1-7/8 7-1/16 3.91

235 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (67)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 402Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED UNION (Old style)Socket x SR Fipt Dimensions Also Applicable to899-XXXSR EPDM O-ring Seal Units

N L

M NUT O.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

859-002SR 1/4 2-1/16 15/16 25/32 1-21/32 .09

859-003SR 3/8 2-9/32 1-1/32 29/32 1-25/32 .13

859-005SR 1/2 2-9/32 1-9/32 21/32 1-31/32 .17859-007SR 3/4 2-19/32 1-17/32 25/32 2-1/2 .28859-010SR 1 2-15/16 1-27/32 25/32 2-7/8 .40859-012SR 1-1/4 3-5/32 2-7/32 29/32 3-5/16 .55859-015SR 1-1/2 3-13/32 2-9/16 1-1/32 3-9/16 .67859-020SR 2 4-3/32 3-1/32 1-19/32 4-3/16 1.12859-030SR 3 5-1/4 4-3/8 1-11/16 5-3/4 2.50859-040SR 4 5-7/8 5-13/32 2-1/8 7-3/32 3.96

1) For (Socket X SR Fipt) Unions Equipped With EPDM O-ring, Replace The 859 With An 899 Before The Dash. e.g. Part Number 899-002SR = 1/4" PVC, Union, Socket x SR Fipt, With EPDM O-rings.

235 psi @ 73°F

UNION 2000Socket x Socket Dimensions Also Applicable to8097-XXX EPDM O-ring Seal Units

NL

NUTO.D. M

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8057-005 1/2 2-3/32 1-3/16 11/32 1-7/8 .12

8057-007 3/4 2-3/8 1-13/32 3/8 2-9/32 .17

8057-010 1 2-11/16 1-23/32 7/16 2-9/16 .288057-012 1-1/4 2-15/16 2-3/32 7/16 3-3/32 .36

1/2" - 4" 235 psi @ 73°F6" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (68)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 403 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

UNION 2000Fipt x Fipt Dimensions Also Applicable to8098-XXX EPDM O-ring Seal Units

LN

MNUTO.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8058-005 1/2 1-29/32 1-3/16 17/32 1-7/8 .08

8058-007 3/4 2-1/16 1-3/8 9/16 2-9/32 .17

8058-010 1 2-17/32 1-11/16 25/32 2-9/16 .218058-012 1-1/4 2-21/32 2-1/32 3/4 3-1/8 .388058-015 1-1/2 2-25/32 2-3/8 29/32 3-1/2 .538058-020 2 3-1/8 3 1-3/16 4-7/32 .898058-025 2-1/2 4-1/32 3-9/16 1-15/32 6-5/32 1.678058-030 3 4-5/32 4-9/32 1-13/32 6-5/32 2.37

8058-040 4 4-21/32 5-1/4 1-21/32 7-3/4 3.59

8058-060 6 6-1/8 7-21/32 2-13/16 11-19/32 12.10

1/2" - 4" 235 psi @ 73°F6" 150 psi @ 73°F

UNION 2000Socket x Socket Dimensions Also Applicable to8097-XXX EPDM O-ring Seal Units

NL

NUTO.D. M

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8057-015 1-1/2 3-1/4 2-3/8 1/2 3-1/2 .50

8057-020 2 3-17/32 2-7/8 17/32 4-9/32 .86

8057-025 2-1/2 4-7/32 3-1/2 25/32 6-5/32 2.14

8057-030 3 4-1/4 4-3/16 1/2 6-5/32 2.16

8057-040 4 5-1/8 5-1/4 5/8 7-3/4 3.75

8057-060 6 6-27/32 7-1/2 25/32 11-5/8 10.38

1/2" - 4" 235 psi @ 73°F6" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (69)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 404Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

SPECIAL REINFORCED UNION 2000SR Fipt x SR Fipt Dimensions Also Applicable to8098-XXXSR EPDM O-ring Seal Units

L

N

M NUT O.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8058-005SR 1/2 2 1-3/16 5/8 1-7/8 .14

8058-007SR 3/4 2-5/32 1-3/8 21/32 2-9/32 .15

8058-010SR 1 2-9/16 1-11/16 13/16 2-9/16 .21

8058-012SR 1-1/4 2-23/32 2-1/32 13/16 3-1/8 .39

8058-015SR 1-1/2 2-27/32 2-13/32 29/32 3-17/32 .59

8058-020SR 2 3-7/32 3-1/32 1-3/16 4-7/32 .97

8058-025SR 2-1/2 4-3/32 3-9/16 1-15/32 6-5/32 1.66

8058-030SR 3 4-3/16 4-9/32 1-3/8 6-5/32 2.44

8058-040SR 4 4-11/16 5-1/4 1-11/16 7-3/4 3.73

8058-060SR 6 6-3/16 7-11/16 2-13/16 11-5/8 10.98

1/2" - 4" 235 psi @ 73°F 6" 150 psi @ 73°F

UNION 2000Socket x Fipt Dimensions Also Applicable to8099-XXX EPDM O-ring Seal Units

N

M

L

NUTO.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8059-005 1/2 1-7/8 1-3/16 5/16 1-7/8 .11

8059-007 3/4 2-1/16 1-13/32 5/16 2-9/32 .18

8059-010 1 2-13/32 1-23/32 13/32 2-9/16 .208059-012 1-1/4 2-19/32 2-3/32 13/32 3-1/8 .358059-015 1-1/2 2-13/16 2-3/8 1/2 3-1/2 .49

1/2" - 4" 235 psi @ 73°F 6" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (70)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 405 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

UNION 2000Socket x Fipt Dimensions Also Applicable to8099-XXX EPDM O-ring Seal Units

N

M

L

NUTO.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8059-020 2 2-31/32 2-7/8 13/32 4-9/32 .92

8059-025 2-1/2 3-15/32 3-1/2 13/32 6-3/16 1.58

8059-030 3 3-25/32 4-3/16 17/32 6-5/32 2.17

8059-040 4 4-3/8 5-1/4 5/8 7-3/4 3.64

8059-060 6 6-27/32 7-1/2 1-1/2 11-5/8 11.69

1/2" - 4" 235 psi @ 73°F 6" 150 psi @ 73°F

UNION 2000Socket x SR Fipt Dimensions Also Applicable to8099-XXXSR EPDM O-ring Seal Units

N

M

L

NUTO.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8059-005SR 1/2 1-29/32 1-3/16 11/32 1-7/8 .12

8059-007SR 3/4 2-5/32 1-13/32 13/32 2-9/32 .14

8059-010SR 1 2-7/16 1-23/32 7/16 2-9/16 .20

8059-012SR 1-1/4 2-5/8 2-3/32 7/16 3-1/8 .37

8059-015SR 1-1/2 2-13/16 2-3/8 1/2 3-1/2 .56

8059-020SR 2 3 2-7/8 7/16 4-7/32 1.00

8059-025SR 2-1/2 3-27/32 3-15/32 27/32 6-3/16 2.19

8059-030SR 3 3-3/4 4-3/16 1/2 6-9/32 2.24

8059-040SR 4 4-3/8 5-1/4 5/8 7-3/4 2.81

8059-060SR 6 6-27/32 7-1/2 2-5/32 11-5/8 11.50

1/2" - 4" 235 psi @ 73°F 6" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (71)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 406Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

UNION 2000Socket x SpigotDimensions Also Applicable to8096-XXX EPDM O-ring Seal Units

PIPEO.D.

NUTO.D. M

L N

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8056-005 1/2 2-5/16 1-3/16 9/16 1-7/8 .12

8056-007 3/4 2-5/8 1-3/8 21/32 2-9/32 .19

8056-010 1 2-15/16 1-23/32 5/8 2-9/16 .298056-012 1-1/4 3-7/32 2-3/32 11/16 3-3/16 .418056-015 1-1/2 3-1/2 2-3/8 11/16 3-9/16 .508056-020 2 3-3/4 2-7/8 3/4 4-5/16 .818056-025 2-1/2 4-21/32 3-15/32 1-5/32 6-5/32 2.238056-030 3 4-25/32 4-5/32 7/32 6-5/32 2.28

8056-040 4 5-5/8 5-1/4 1-1/8 7-23/32 3.95

8056-060 6 7-3/4 7-9/16 1-1/2 11-11/16 11.84

1/2" - 4" 235 psi @ 73°F6" 150 psi @ 73°F

PVC TRANSITION UNION DIN (mm) Socket x ASTM (in) Socket Dimensions Also Applicable to 8697-XXX EPDM O-ring Seal Units

N L

NUT O.D. M

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8657-020 20mm x 1/2 2-1/16 1-9/32 5/16 1-31/32 .16

8657-025 25mm x 3/4 2-11/32 1-17/32 11/32 2-1/2 .27

8657-032 32mm x 1 2-9/16 1-27/32 3/8 2-7/8 .378657-040 40mm x 1-1/4 2-7/8 2-7/32 3/8 3-5/16 .528657-050 50mm x 1-1/2 3-1/8 2-9/16 5/16 3-9/16 .598657-063 63mm x 2 3-5/8 3-1/32 9/16 4-3/16 .948657-090 90mm x 3 5-1/16 4-3/8 1-3/16 5-3/4 2.318657-110 110mm x 4 5-7/8 5-7/16 1-3/8 7-1/16 3.91

235 psi @ 73°F (PN 16 @ 22°C)

1) For DIN (mm) Socket X ASTM (in) Socket Unions Equipped with EPDM O-ring, Replace The 8657 With An 8697 Before The Dash. e.g. Part Number 8697-020 = 20mm x 1/2" PVC, Union Socket x Socket With EPDM O-rings.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (72)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 407 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PVC TRANSITION UNION DIN (mm) Socket x ASTM (in) Fipt Dimensions Also Applicable to 8698-XXX EPDM O-ring Seal Units

MNUT O.D.

NL

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8658-020 20 mm x 1/2 2-3/32 1-9/32 19/32 1-31/32 .16

8658-025 25mm x 3/4 2-3/8 1-17/32 3/4 2-1/2 .28

8658-032 32mm x 1 2-9/16 1-27/32 7/16 2-7/8 .388658-040 40mm x 1-1/4 2-7/8 2-7/32 7/8 3-5/16 .568658-050 50mm x 1-1/2 3-3/32 2-9/16 1-5/32 3-9/16 .618658-063 63mm x 2 3-9/16 3-1/32 1-5/8 4-3/16 .998658-090 90mm x 3 5-1/16 4-3/8 1-13/16 5-3/4 2.418658-110 110mm x 4 5-7/8 5-7/16 2-3/8 7-1/16 4.07

235 psi @ 73°F (PN 16 @ 22°C)

1) For DIN (mm) Socket X NPT (in) Fipt Unions Equipped with EPDM O-ring, Replace The 8658 With An 8698 Before The Dash. e.g. Part Number 8698-020 = 20mm x 1/2" PVC, Union, DIN Socket x ASTM Fipt With EPDM O-rings.

PVC TRANSITION UNION JIS (mm) Socket X ASTM (in) Socket Dimensions Also Applicable to 8297-XXX EPDM O-ring Seal Units

N L

NUT O.D. M

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8257-016 16 DN x 1/2 2-1/16 1-9/32 5/16 1-31/32 .15

8257-020 20 DN x 3/4 2-3/8 1-17/32 5/16 2-1/2 .26

8257-025 25 DN x 1 2-9/16 1-27/32 3/8 2-7/8 .378257-030 30 DN x 1-1/4 2-15/16 2-3/32 7/16 3-3/16 .428257-040 40 DN x 1-1/2 3-1/8 2-9/16 5/16 3-9/16 .618257-050 50 DN x 2 3-5/8 3-1/32 9/16 4-3/16 .978257-075 75 DN x 3 5-1/16 4-3/8 1-3/16 5-3/4 2.348257-100 100 DN x 4 5-7/8 5-13/32 1-11/32 7-1/8 3.75

235 psi @ 73°F (PN 16 @ 22°C)

1) For JIS (mm) Socket X ASTM (in) Socket Unions Equipped with EPDM O-ring, Replace The 8257 With An 8297 Before The Dash. e.g. Part Number 8297-016 = 16mm x 1/2" PVC, Union, JIS Socket x ASTM Socket With EPDM O-rings.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (73)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 408Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PVC TRANSITION UNION JIS (mm) Socket X ASTM (in) Fipt Dimensions Also Applicable to 8298-XXX EPDM O-ring Seal Units

L N

M NUT O.D.

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8258-016 16 DN x 1/2 2-3/32 1-9/32 19/32 1-31/32 .16

8258-020 20 DN x 3/4 2-3/8 1-17/32 3/4 2-1/2 .27

8258-025 25 DN x 1 2-25/32 1-23/32 13/16 2-21/32 .388258-030 30 DN x 1-1/4 2-7/8 2-7/32 7/8 3-5/16 .578258-040 40 DN x 1-1/2 3-1/8 2-17/32 25/32 3-17/32 .638258-050 50 DN x 2 3-11/16 2-7/8 1-7/32 4-9/32 1.028258-075 75 DN x 3 5-1/16 4-3/8 1-13/16 5-3/4 2.438258-100 100 DN x 4 5-7/8 5-7/16 2-3/8 7-1/16 3.96

235 psi @ 73°F (PN 16 @ 22°C)

1) For JIS (mm) Socket X ASTM (in) Fipt Unions Equipped with EPDM O-ring, Replace The 8258 With An 8298 Before The Dash. e.g. Part Number 8298-016 = 16dn x 1/2" PVC, Union, JIS Socket x ASTM Fipt With EPDM O-rings.

PVC TRANSITION UNION BSP Threaded x ASTM (in) Socket Dimensions Also Applicable to 8399-XXX EPDM O-ring Seal Units

NUT O.D. M

L N

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8359-005 1/2 1-29/32 1-3/16 13/32 1-15/16 .12

8359-007 3/4 2-3/8 1-17/32 9/16 2-1/2 .27

8359-010 1 2-9/16 1-27/32 13/32 2-7/8 .388359-012 1-1/4 2-5/8 2-1/4 7/16 3-3/16 .378359-015 1-1/2 3-3/32 2-9/16 23/32 3-9/16 .628359-020 2 3-1/32 3 17/32 4-1/4 .858359-030 3 5 4-3/8 1-11/16 5-25/32 2.438359-040 4 5-7/8 5-7/16 1-7/8 7-1/16 3.84

235 psi @ 73°F (PN 16 @ 22°C)

1) For BSP Threaded X ASTM (in) Socket Unions Equipped with EPDM O-ring, Replace The 8359 With An 8399 Before The Dash. e.g. Part Number 8399-005 = 1/2" PVC, Union, BSP Thread x ASTM Socket With EPDM O-rings.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (74)

Schedule 80 PVC Technical Information

Schedule 80 Unions

Page 409 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PVC TRANSITION UNION BSP Threaded x ASTM (in.) Fipt Dimensions Also Applicable to 8398-XXX EPDM O-ring Seal Units

NUT O.D. M

L N

Part Numberw/FKM O-ring Seal Size L M N Nut

O.D. Approx. Wt. (Lbs.)

8358-005 1/2 2-3/32 1-9/32 19/32 1-31/32 .16

8358-007 3/4 2-3/8 1-17/32 27/32 2-1/2 .28

8358-010 1 2-9/16 1-27/32 7-16 2-7/8 .398358-012 1-1/4 2-23/32 2-1/32 27/32 3-3/16 .408358-015 1-1/2 3-3/32 2-9/16 1-5/32 3-9/16 .648358-020 2 3-9/16 3-1/32 1-5/8 4-3/16 1.058358-030 3 5-1/32 4-11/32 1-15/16 5-25/32 2.528358-040 4 5-7/8 5-7/16 2-3/8 7-1/16 4.00

1) For BSP Threaded X ASTM Fipt Unions Equipped with EPDM O-ring, Replace The 8358 With An 8398 Before The Dash. e.g. Part Number 8398-005 = 1/2" PVC, Union, BSP Thread x ASTM Fipt With EPDM O-rings.

235 psi @ 73°F (PN 16 @ 22°C)

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (75)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 410Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP-ON SADDLESSimple Two-Piece Design Engineered for Reliability

Excellent Metal-to-Plastic System TransitionEasily installs on metal pipe as a transition to plastic system.

PVC Tee or Cross Con gurationsAvailable in PVC White, PVC Gray in 2" - 12" IPS pipe saddle with socket outlets in sizes 1/2" - 6" and Special Reinforced (SR)threaded outlets in sizes 1/2" - 6", single Tee or double Cross con gurations.

Patented SR Design Female ThreadsPatented Special Reinforced (SR) design on female thread outlets for superior strength.

O-ring OptionsChoice of high grade Buna-N or EPDM O-rings for Schedule 40 and EPDM or FKM O-rings for Schedule 80, for application speci c selection for optimum chemical resistance.

Multi-Bolt Design, Choice of HardwarePositive attachment eliminates splitting problems associated with plastic wedge fasteners and outperforms 2-Bolt clamp saddle designs. Choose zinc plated or stainless steel nut, bolt and washer hardware.

Excellent Pressure CapabilitiesMaximum internal pressure rating of 235 psi through 4", 200 psi for 6", and 150 psi for 8" - 12" at 73°F.

Sample Engineering Speci cationAll thermoplastic saddles shall be clamp-on type with O-ring seal constructed from PVC Type I cell classi cation 12454. All O-rings shall be Buna-N, EPDM or FKM. All saddles shall be piloted at O-ring area for positive positioning in pipe. All bolt clamping hardware shall be zinc plated steel or stainless steel. All threaded saddle outlets shall be Special Reinforced (SR) design. Saddles shall be pressure rated at 235 psi for use on pipe sizes through 4" nominal IPS diameters, 200 psi for use on 6" pipe, and 150 psi for use on 8" - 12" pipe, maximum internal pressure for water at 73°F, as manufactured by Spears® Manufacturing Company.

Spears® PVC Clamp-On Saddles allow quick, easy and reliable addition of branch lines to existing piping system lines. Th ese versatile saddle units can be used in either temporary or permanent installations on all types of pipewith IPS (Iron Pipe size) outside diameter, such as PVC, CPVC, Polyethylene, Polypropylene and Steel.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (76)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Page 411 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Clamp-On Saddle Installation Instructions

1. Using a standard industrial grade hole-saw, cut specified hole in desired position on pipe according to recommended hole saw size engraved on the saddle. Note: Care must be taken to deburr hole and remove all residue from hole area to assure tight fit and avoid leakage.

2. Fully seat O-ring in groove on underside of saddle outlet component. Position over hole and fully seat saddle onto pipe. Note: Certain saddle outlets are piloted. Be sure pilot lip fully engages with hole in pipe.

3. Place strap component opposite outlet and secure with bolts (4), nuts (4) and washers (8). Important: Washers MUST be placed under each bolt head (1) and under each nut (1) to avoid damage to saddle.

4. Tighten bolts to specified torque.

Saddle Size 2 3 4 6 & upRecommended Bolt-Torque -ft/lb 8 8 8 10

For Double Outlet Saddle Installation —Determine second outlet hole position as shown

O-ring seal provides positive, trouble-free sealing to pipe.

Special pilot engages with hole in pipe to prevent saddle dislocation.

a

a

a a1/2 a-a

Drill Pilot Hole before using Hole Saw.

O-RING

PILOT

CLAMP-ON SADDLE

PIPE

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (77)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 412Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SOCKETSINGLE OUTLET Dimensions Also Applicable to 866S-XXX, 866V-XXX & 866SV-XXX

L L1

H

H1

M N

Part Number Size H H1 L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

866-247 2x1/2 2-3/8 1-1/2 2-7/16 3-7/16 1-3/16 5/16 3/4 8 .56

866-248 2x3/4 2-1/2 1-1/2 2-7/16 3-7/16 1-3/8 5/16 7/8 8 .57

866-249 2x1 2-5/8 1-1/2 2-7/16 3-7/16 1-11/16 5/16 1-1/8 8 .40

866-250 2x1-1/4 2-3/4 1-1/2 2-7/16 3-7/16 2-1/16 5/16 1-1/2 8 .68

866-251 2x1-1/2 2-15/16 1-1/2 2-7/16 3-7/16 2-3/8 5/16 1-1/2 8 .65

866-291 2-1/2x1-1/2 3-3/16 1-11/16 4-1/16 4 2-3/8 3/8 1-3/4 8 1.02

866-3331 3x1/2 3-5/16 2-1/16 3 4-5/8 1-3/8 13/16 7/8 8 .88

866-334 3x3/4 3-1/16 2-1/16 3 4-5/8 1-3/8 9/32 7/8 8 .85

866-335 3x1 3-3/16 2-1/16 3 4-5/8 1-11/16 5/16 1-1/8 8 .91

866-3361 3x1-1/4 4-1/32 2-1/16 4-3/32 4-5/8 3 1-1/32 2-1/4 8 1.48

866-3371 3x1-1/2 4-1/32 2-1/16 4-3/32 4-5/8 3 29/32 2-1/4 8 1.41

866-338 3x2 3-5/8 2-1/16 4-3/32 4-5/8 3 3/8 2-1/4 8 1.24

866-4151 4x1/2 4-3/32 2-5/8 3 5-9/16 2-3/8 31/32 1-1/8 8 1.31

866-4161 4x3/4 4-3/32 2-5/8 3 5-9/16 2-3/8 27/32 1-1/8 8 1.29

866-417 4x1 3-13/16 2-5/8 3 5-5/8 1-11/16 7/16 1-1/8 8 1.24

866-4181 4x1-1/4 4-13/32 2-5/8 4-3/32 5-5/8 2-3/8 29/32 1-3/4 8 1.70

866-419 4x1-1/2 4-1/8 2-5/8 4-3/32 5-9/16 2-3/8 1/2 1-3/4 8 1.63

866-420 4x2 4-3/16 2-5/8 4-1/8 5-5/8 3 7/16 2-1/4 8 1.69

866-4211 4x2-1/2 5 2-5/8 5-7/16 5-23/32 4-9/32 3/4 3 8 2.78

866-422 4x3 4-5/8 2-19/32 5-7/16 5-11/16 4-1/4 1/2 3 8 2.39

866-5231 6x1/2 5-13/32 3-7/8 3 7-3/4 1-11/16 1-7/32 1-1/8 10 2.35

866-5241 6x3/4 5-7/16 3-7/8 3 7-3/4 1-11/16 1-1/8 1-1/8 10 2.33

866-525 6x1 5-1/8 3-7/8 3 7-15/16 1-11/16 11/16 1-1/8 10 2.29

866-5261 6x1-1/4 5-15/16 3-7/8 4-1/8 7-3/4 3 1-3/8 2-1/4 10 3.28

866-5271 6x1-1/2 5-15/16 3-7/8 4-1/8 7-3/4 3 1-1/4 2-1/4 10 3.22

866-528 6x2 5-1/2 3-7/8 4-1/8 7-3/4 3 11/16 2-1/4 10 3.04

866-5291 6x2-1/2 6-7/16 3-7/8 6 7-15/16 4-1/4 1-1/8 3 10 4.73

866-530 6x3 5-15/16 3-7/8 6 7-15/16 4-1/4 25/32 3 10 4.35

866-532 6x4 6 3-29/32 6 7-15/16 5-3/16 5/8 4 10 5.091 Outlet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (78)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Page 413 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SOCKETSINGLE OUTLET Dimensions Also Applicable to 866S-XXX, 866V-XXX & 866SV-XXX

L L1

H

H1

M N

Part Number Size H H1 L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

866-5731 8x1/2 7-3/4 4-7/8 9-1/2 8-1/2 5-5/16 1-1/2 4 10 9.70

866-5741 8x3/4 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-3/4 4 10 9.65

866-5751 8x1 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-5/8 4 10 9.67

866-5761 8x1-1/4 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-1/2 4 10 9.79

866-5771 8x1-1/2 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-3/8 4 10 10.23

866-5781 8x2 7-11/16 4-7/8 8-1/2 10-1/8 5-1/4 1-7/8 4 10 10.28

866-5791 8x2-1/2 8-5/32 4-7/8 8-15/32 10 5-7/32 2-1/2 4 10 9.43

866-5801 8x3 7-11/16 4-7/8 8-1/2 10-1/8 5-1/4 1-7/16 4 10 10.21

866-582 8x4 7-5/16 4-7/8 8-1/2 10-1/8 5-1/4 11/16 4 10 12.22

866-585 8x6 8-3/32 4-7/8 8-1/2 10-1/8 7-5/8 11/16 6 10 9.80

866-6211 10x2 8-7/8 6-1/32 8-1/2 12-5/16 5-1/4 1-15/16 4 10 13.02

866-624 10x4 8-15/32 6-1/32 8-1/2 12-5/16 5-1/4 13/16 4 10 11.92

866-626 10x6 9-9/32 6-1/32 8-1/2 12-5/16 7-5/8 13/16 6 10 12.92

866-664 12x4 9-9/16 7-5/32 8-1/2 14-5/16 5-1/4 7/8 4 10 15.47

866-666 12x6 10-3/8 7-5/32 8-1/2 14-5/16 7-5/8 7/8 6 10 16.331 Outet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

1) Clamp On Saddle Standard Hardware: Zinc Bolts w/EPDM O-ring Seale.g. Part Number 866-247 = 2x1/2 PVC Clamp On Saddle, Socket, EPDM O-ring, Zinc Bolts.

2) Clamp On Saddles w/Stainless Steel (SS) Bolts,Add The Letter “S” Before The Dash.e.g. Part Number 866S-247 = 2x1/2 PVC Clamp On Saddle, Socket, EPDM O-ring, Stainless Steel Bolts.

3) Clamp On Saddles w/FKM O-ring Seal, Add The Letter “V” Before The Dash.e.g. Part Number 866V-247 = 2x1/2 PVC Clamp-On Saddle, Socket, FKM O-ring, Zinc Bolts.

4) Clamp-On Saddles w/Stainless Steel Bolts & FKM O-ring Seal, Add The Letter “SV” Before The Dash.e.g. Part Number 866SV-247 = 2x1/2 PVC Clamp On Saddle, Socket FKM O-ring, Stainless Steel Bolts.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (79)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 414Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SR FIPTSINGLE OUTLET Dimensions Also Applicable to 867S-XXXSR, 867V-XXXSR & 867SV-XXXSR

N

L

M

L1

H

H1

Part Number Size H H1 L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

867-247SR 2x1/2 2-3/8 1-1/2 2-7/16 3-7/16 1-3/16 5/16 3/4 3/4 .56

867-248SR 2x3/4 2-1/2 1-1/2 2-7/16 3-7/16 1-3/8 5/8 7/8 7/8 .57

867-249SR 2x1 2-5/8 1-1/2 2-7/16 3-7/16 1-11/16 9/16 1-1/8 1-1/8 .40

867-250SR 2x1-1/4 2-3/4 1-1/2 2-7/16 3-7/16 2-1/16 11/16 1-1/2 1-1/2 .61

867-251SR 2x1-1/2 2-15/16 1-1/2 2-7/16 3-7/16 2-3/8 3/4 1-1/2 1-1/2 .65

867-291SR 2-1/2x1-1/2 3-3/16 1-11/16 4-1/16 4 2-3/8 13/16 1-3/4 1-3/4 1.02

867-333SR1 3x1/2 3-5/16 2-1/16 3 4-5/8 1-3/8 15/16 7/8 7/8 .89

867-334SR 3x3/4 3-1/16 2-1/16 3 4-5/8 1-3/8 9/16 7/8 7/8 .87

867-335SR 3x1 3-3/16 2-1/16 3 4-5/8 1-11/16 9/16 1-1/8 1-1/8 .89

867-336SR1 3x1-1/4 4-1/32 2-1/16 4-3/32 4-5/8 3 1-5/16 2-1/4 2-1/4 1.51

867-337SR1 3x1-1/2 4-1/32 2-1/16 4-3/32 4-5/8 3 2-11/16 2-1/4 2-1/4 1.47

867-338SR 3x2 3-5/8 2-1/16 4-3/32 4-5/8 3 7/8 2-1/4 2-1/4 1.36

867-415SR1 4x1/2 4-3/32 2-5/8 3 5-9/16 2-3/8 1-1/8 1-1/8 1-1/8 1.32

867-416SR1 4x3/4 4-3/32 2-5/8 3 5-9/16 2-3/8 1-1/8 1-1/8 1-1/8 1.31

867-417SR 4x1 3-13/16 2-5/8 3 5-5/8 1-11/16 11/16 1-1/8 1-1/8 1.26

867-418SR1 4x1-1/4 4-13/32 2-5/8 4-3/32 5-5/8 2-3/8 1-7/32 1-3/4 1-3/4 1.75

867-419SR1 4x1-1/2 4-1/8 2-5/8 4-3/32 5-9/16 2-3/8 15/16 1-3/4 1-3/4 1.68

867-420SR 4x2 4-3/16 2-5/8 4-1/8 5-5/8 3 15/16 2-1/4 2-1/4 1.78

867-421SR1 4x2-1/2 5 2-5/8 5-7/16 5-23/32 4-9/32 1-7/32 3 3 2.91

867-422SR 4x3 4-5/8 2-19/32 5-7/16 5-11/16 4-1/4 31/32 3 3 2.53

867-523SR1 6x1/2 5-13/32 3-7/8 3 7-3/4 1-11/16 1-3/8 1-1/8 1-1/8 2.37

867-524SR1 6x3/4 5-7/16 3-7/8 3 7-3/4 1-11/16 1-3/8 1-1/8 1-1/8 2.35

867-525SR 6x1 5-1/8 3-7/8 3 7-15/16 1-11/16 15/16 1-1/8 1-1/8 2.31

867-526SR1 6x1-1/4 5-15/16 3-7/8 4-1/8 7-3/4 3 1-11/16 2-1/4 2-1/4 3.31

867-527SR1 6x1-1/2 5-15/16 3-7/8 4-1/8 7-3/4 3 1-3/4 2-1/4 2-1/4 3.27

867-528SR 6x2 5-1/2 3-7/8 4-1/8 7-3/4 3 1-7/32 2-1/4 2-1/4 3.13

867-529SR1 6x2-1/2 6-7/16 3-7/8 6 7-15/16 4-1/4 1-9/16 3 3 4.87

867-530SR 6x3 5-15/16 3-7/8 6 7-15/16 4-1/4 1-1/4 3 3 4.46

867-532SR 6x4 6 3-29/32 6 7-15/16 5-3/16 1-3/8 4 4 5.441 Outlet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (80)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Page 415 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SR FIPTSINGLE OUTLET Dimensions Also Applicable to 867S-XXXSR, 867V-XXXSR & 867SV-XXXSR

N

L

M

L1

H

H1

Part Number Size H H1 L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

867-573SR 8x1/2 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 3 4 10 9.69

867-574SR1 8x3/4 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 3 4 10 9.70

867-575SR 8x1 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-13/16 4 10 9.81

867-576SR1 8x1-1/4 9-5/16 4-15/16 8-9/16 9-29/32 5-7/32 1-19 /32 4 10 9.68

867-577SR1 8x1-1/2 8-3/32 4-7/8 8-1/2 10-1/8 5-1/4 2-3/4 4 10 ---

867-578SR1 8x2 7-11/16 4-7/8 8-1/2 10-1/8 5-1/4 2-3/8 4 10 ---

867-579SR1 8x2-1/2 8-1/8 4-7/8 8-1/2 10-1/8 5-1/4 2-1/2 4 10 ---

867-580SR1 8x3 7-11/16 4-7/8 8-1/2 10-1/8 5-1/4 1-15/16 4 10 ---

867-582SR 8x4 7-5/16 4-7/8 8-1/2 10-1/8 5-1/4 1-1/2 4 10 7.74

867-585SR 8x6 8-3/32 4-7/8 8-1/2 10-1/8 7-5/8 2-3/32 6 10 8.61

867-624SR 10x4 8-15/32 6-1/32 8-1/2 12-5/16 5-1/4 2-3/16 4 10 ---

867-626SR 10x6 9-9/32 6-1/32 8-1/2 12-5/16 7-5/8 3-3/16 6 10 ---

867-664SR 12x4 9-9/16 7-5/32 8-1/2 14-5/16 5-1/4 1-5/8 4 10 ---

867-666SR 12x6 10-3/8 7-5/32 8-1/2 14-5/16 7-5/8 2-1/4 6 10 ---1 Outlet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

1) Clamp On Saddle Standard Hardware: Zinc Bolts w/EPDM O-ring Seale.g. Part Number 867-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded, EPDM O-ring, Zinc Bolts.

2) Clamp On Saddles w/Stainless Steel (SS) Bolts,Add The Letter “S” Before The Dash.e.g. Part Number 867S-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded, EPDM O-ring, Stainless Steel Bolts.

3) Clamp On Saddles w/FKM O-ring Seal, Add The Letter “V” Before The Dash.e.g. Part Number 867V-247SR = 2x1/2 PVC Clamp-On Saddle, SR Threaded, FKM O-ring, Zinc Bolts.

4) Clamp-On Saddles w/Stainless Steel Bolts & FKM O-ring Seal, Add The Letter “SV” Before The Dash. e.g. Part Number 867SV-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded FKM O-ring, Stainless Steel Bolts.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (81)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 416Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SOCKETDOUBLE OUTLET Dimensions Also Applicable to 868S-XXX, 868V-XXX & 868SV-XXX

M N

H

L1 L

Part Number Size H L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

868-247 2x1/2 2-3/8 2-7/16 3-7/16 1-3/16 5/16 3/4 8 .56

868-248 2x3/4 2-1/2 2-7/16 3-7/16 1-3/8 5/16 7/8 8 .57

868-249 2x1 2-5/8 2-7/16 3-7/16 1-11/16 5/16 1-1/8 8 .40

838-250 2x1-1/4 2-3/4 2-7/16 3-7/16 2-1/16 5/16 1-1/2 8 .61

868-251 2x1-1/2 2-15/16 2-7/16 3-7/16 2-3/8 5/16 1-1/2 8 .65

868-291 2-1/2x1-1/2 3-3/16 4-1/16 4 2-3/8 3/8 1-3/4 8 1.02

868-3331 3x1/2 3-5/16 3 4-5/8 1-3/8 13/16 7/8 8 .93

868-334 3x3/4 3-1/16 3 4-5/8 1-3/8 9/32 7/8 8 .89

868-335 3x1 3-3/16 3 4-5/8 1-11/16 5/16 1-1/8 8 .91

868-3361 3x1-1/4 4-1/32 4-3/32 4-5/8 3 1-1/32 2-1/4 8 1.94

868-3371 3x1-1/2 4-1/32 4-3/32 4-5/8 3 29/32 2-1/4 8 1.82

868-338 3x2 3-5/8 4-3/32 4-5/8 3 3/8 2-1/4 8 1.47

868-4151 4x1/2 4-3/32 3 5-9/16 2-3/8 31/32 1-1/8 8 1.43

868-4161 4x3/4 4-3/32 3 5-9/16 2-3/8 27/32 1-1/8 8 1.39

868-417 4x1 3-13/16 3 5-5/8 1-11/16 7/16 1-1/8 8 1.30

868-4181 4x1-1/4 4-13/32 4-3/32 5-5/8 2-3/8 29/32 1-3/4 8 1.92

868-419 4x1-1/2 4-1/8 4-3/32 5-9/16 2-3/8 1/2 1-3/4 8 1.77

868-420 4x2 4-3/16 4-1/8 5-5/8 3 7/16 2-1/4 8 1.90

868-4211 4x2-1/2 5 5-7/16 5-23/32 4-9/32 3/4 3 8 3.69

868-422 4x3 4-5/8 5-7/16 5-11/16 4-1/4 1/2 3 8 2.92

868-5231 6x1/2 5-13/32 3 7-3/4 1-11/16 1-7/32 1-1/8 10 2.48

868-5241 6x3/4 5-7/16 3 7-3/4 1-11/16 1-1/8 1-1/8 10 2.44

868-525 6x1 5-1/8 3 7-15/16 1-11/16 11/16 1-1/8 10 2.35

868-5261 6x1-1/4 5-15/16 4-1/8 7-3/4 3 1-3/8 2-1/4 10 3.72

868-5271 6x1-1/2 5-15/16 4-1/8 7-3/4 3 1-1/4 2-1/4 10 3.60

868-528 6x2 5-1/2 4-1/8 7-3/4 3 11/16 2-1/4 10 3.25

868-5291 6x2-1/2 6-7/16 6 7-15/16 4-1/4 1-1/8 3 10 5.58

868-530 6x3 5-15/16 6 7-15/16 4-1/4 25/32 3 10 4.81

868-532 6x4 6 6 7-15/16 5-3/16 5/8 4 10 5.56

868-5731 8x1/2 8-3/32 8-1/2 10-1/8 5-1/4 2-3/16 4 10 11.501 Outlet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (82)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Page 417 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SOCKETDOUBLE OUTLET Dimensions Also Applicable to 868S-XXX, 868V-XXX & 868SV-XXX

M N

H

L1 L

Part Number Size H L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

868-5741 8x3/4 8-3/32 8-1/2 10-1/8 5-1/4 2-3/4 4 10 11.45

868-5751 8x1 8-3/32 8-1/2 10-1/8 5-1/4 2-5/8 4 10 11.52

868-5761 8x1-1/4 8-3/32 8-1/2 10-1/8 5-1/4 2-1/2 4 10 11.48

868-5771 8x1-1/2 8-3/32 8-1/2 10-1/8 5-1/4 2-3/8 4 10 11.30

868-5781 8x2 7-11/16 8-1/2 10-1/8 5-1/4 1-7/8 4 10 11.00

868-5791 8x2-1/2 8-1/8 8-1/2 10-1/8 5-1/4 1-11/16 4 10 8.90

868-5801 8x3 7-11/16 8-1/2 9-7/8 5-7/32 2-1/16 4 10 10.25

868-582 8x4 7-5/16 8-1/2 10-1/8 5-1/4 11/16 4 10 8.00

868-585 8x6 8-3/32 8-1/2 10-1/8 7-5/8 11/16 6 10 10.32

868-624 10x4 8-15/32 8-1/2 12-5/16 5-1/4 13/16 4 10 15.37

868-626 10x6 9-9/32 8-1/2 12-5/16 7-5/8 13/16 6 10 14.51

868-664 12x4 9-9/16 8-1/2 14-5/16 5-1/4 7/8 4 10 15.75

868-666 12x6 10-3/8 8-1/2 14-5/16 7-5/8 7/8 6 10 17.581 Outlet sized with bushing

1) Clamp On Saddle Standard Hardware: Zinc Bolts w/EPDM O-ring Seale.g. Part Number 868-247 = 2x1/2 PVC Clamp On Saddle, Socket, EPDM O-ring, Zinc Bolts.

2) Clamp On Saddles w/Stainless Steel (SS) Bolts,Add The Letter “S” Before The Dash.e.g. Part Number 868S-247 = 2x1/2 PVC Clamp On Saddle, Socket, EPDM O-ring, Stainless Steel Bolts.

3) Clamp On Saddles w/FKM O-ring Seal, Add The Letter “V” Before The Dash.e.g. Part Number 868V-247 = 2x1/2 PVC Clamp-On Saddle, Socket, FKM O-ring, Zinc Bolts.

4) Clamp-On Saddles w/Stainless Steel Bolts & FKM O-ring Seal, Add The Letter “SV” Before The Dash.e.g. Part Number 868SV-247 = 2x1/2 PVC Clamp On Saddle, Socket FKM O-ring, Stainless Steel Bolts.

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (83)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 418Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SR FIPTDOUBLE OUTLET Dimensions Also Applicable to 869S-XXXSR, 869V-XXXSR & 869SV-XXXSR

N M

H

L1 L

Part Number Size H L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

869-247SR 2x1/2 2-3/8 2-7/16 3-7/16 1-3/16 5/16 3/4 8 .56

869-248SR 2x3/4 2-1/2 2-7/16 3-7/16 1-3/8 5/8 7/8 8 .57

869-249SR 2x1 2-5/8 2-7/16 3-7/16 1-11/16 9/16 1-1/8 8 .40

869-250SR 2x1-1/4 2-3/4 2-7/16 3-7/16 2-1/16 11/16 1-1/2 8 .61

869-251SR 2x1-1/2 2-15/16 2-7/16 3-7/16 2-3/8 3/4 1-1/2 8 .65

869-291SR 2-1/2x1-1/2 3-3/16 4-1/16 4 2-3/8 13/16 1-3/4 8 1.02

869-333SR1 3x1/2 3-5/16 3 4-5/8 1-3/8 15/16 7/8 8 .96

869-334SR 3x3/4 3-1/16 3 4-5/8 1-3/8 9/16 7/8 8 .93

869-335SR 3x1 3-3/16 3 4-5/8 1-11/16 9/16 1-1/8 8 .95

869-336SR1 3x1-1/4 4-1/32 4-3/32 4-5/8 3 1-5/16 2-1/4 8 2.01

869-337SR1 3x1-1/2 4-1/32 4-3/32 4-5/8 3 2-11/16 2-1/4 8 1.93

869-338SR 3x2 3-5/8 4-3/32 4-5/8 3 7/8 2-1/4 8 1.71

869-415SR1 4x1/2 4-3/32 3 5-9/16 2-3/8 1-1/8 1-1/8 8 1.46

869-416SR1 4x3/4 4-3/32 3 5-9/16 2-3/8 1-1/8 1-1/8 8 1.43

869-417SR 4x1 3-13/16 3 5-5/8 1-11/16 11/16 1-1/8 8 1.34

869-418SR1 4x1-1/4 4-13/32 4-3/32 5-5/8 2-3/8 1-7/32 1-3/4 8 2.02

869-419SR 4x1-1/2 4-1/8 4-3/32 5-9/16 2-3/8 15/16 1-3/4 8 1.87

869-420SR 4x2 4-3/16 4-1/8 5-5/8 3 15/16 2-1/4 8 2.08

869-421SR1 4x2-1/2 5 5-7/16 5-23/32 4-9/32 1-7/32 3 8 3.96

869-422SR 4x3 4-5/8 5-7/16 5-11/16 4-1/4 31/32 3 8 3.19

869-523SR1 6x1/2 5-13/32 3 7-3/4 1-11/16 1-3/8 1-1/8 10 2.51

869-524SR1 6x3/4 5-7/16 3 7-3/4 1-11/16 1-3/8 1-1/8 10 2.48

869-525SR 6x1 5-1/8 3 7-15/16 1-11/16 15/16 1-1/8 10 2.39

869-526SR1 6x1-1/4 5-15/16 4-1/8 7-3/4 3 1-11/16 2-1/4 10 3.79

869-527SR1 6x1-1/2 5-15/16 4-1/8 7-3/4 3 1-3/4 2-1/4 10 3.70

869-528SR 6x2 5-1/2 4-1/8 7-3/4 3 1-7/32 2-1/4 10 3.43

869-529SR1 6x2-1/2 6-7/16 6 7-15/16 4-1/4 1-9/16 3 10 5.85

869-530SR 6x3 5-15/16 6 7-15/16 4-1/4 1-1/4 3 10 5.04

869-532SR 6x4 6 6 7-15/16 5-3/16 1-3/8 4 10 6.26

869-573SR1 8x1/2 8-3/32 8-1/2 10-1/8 5-1/4 3 4 10 11.521 Outlet sized with bushing

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (84)

Schedule 80 PVC Technical Information

Schedule 80 Saddles

Page 419 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

CLAMP ON SADDLE x SR FIPTDOUBLE OUTLET Dimensions Also Applicable to 869S-XXXSR, 869V-XXXSR & 869SV-XXXSR

N M

H

L1 L

Part Number Size H L L1 M N HoleSize

BoltTorqueft./lbs.

Approx. Wt. (Lbs.)

869-574SR1 8x3/4 8-3/32 8-1/2 10-1/8 5-1/4 3 4 10 ---

869-575SR1 8x1 8-3/32 8-1/2 10-1/8 5-1/4 2-13/16 4 10 ---

869-576SR1 8x1-1/4 8-3/32 8-1/2 10-1/8 5-1/4 2-3/4 4 10 ---

869-577SR1 8x1-1/2 8-3/32 8-1/2 10-1/8 5-1/4 2-3/4 4 10 ---

869-578SR1 8x2 7-11/16 8-1/2 10-1/8 5-1/4 2-3/8 4 10 ---

869-579SR1 8x2-1/2 8-1/8 8-1/2 10-1/8 5-1/4 2-1/2 4 10 ---

869-580SR1 8x3 7-11/16 8-1/2 10-1/8 5-1/4 1-15/16 4 10 ---

869-582SR 8x4 7-5/16 8-1/2 10-1/8 5-1/4 1-1/2 4 10 8.59

869-585SR 8x6 8-3/32 8-1/2 10-1/8 7-5/8 2-3/32 6 10 10.32

869-624SR 10x4 8-15/32 8-1/2 12-5/16 5-1/4 2-3/16 4 10 ---

869-626SR 10x6 9-9/32 8-1/2 12-5/16 7-5/8 3-3/16 6 10 ---

869-664SR 12x4 9-9/16 8-1/2 14-5/16 5-1/4 1-5/8 4 10 ---

869-666SR 12x6 10-3/8 8-1/2 14-5/16 7-5/8 2-1/4 6 10 ---1 Outlet sized with bushing

1) Clamp On Saddle Standard Hardware: Zinc Bolts w/EPDM O-ring Seale.g. Part Number 869-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded, EPDM O-ring, Zinc Bolts.

2) Clamp On Saddles w/Stainless Steel (SS) Bolts, Add The Letter “S” Before The Dash.e.g. Part Number 869S-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded, EPDM O-ring, Stainless Steel Bolts.

3) Clamp On Saddles w/FKM O-ring Seal, Add The Letter “V” Before The Dash.e.g. Part Number 869V-247SR = 2x1/2 PVC Clamp-On Saddle, SR Threaded, FKM O-ring, Zinc Bolts.

4) Clamp-On Saddles w/Stainless Steel Bolts & FKM O-ring Seal, Add The Letter “SV” Before The Dash.e.g. Part Number 869SV-247SR = 2x1/2 PVC Clamp On Saddle, SR Threaded FKM O-ring, Stainless Steel Bolts.

2" - 4" 235 psi @ 73°F6" 200 psi @ 73°F

8" - 12" 150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (85)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 420Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Tank Adapters (Bulkhead Fittings)Designed to facilitate connections through tank or bulkhead walls. Available in PVC or CPVC with socket x socket, Socket x threador SR thread, thread x thread or thread x SR thread, and spigot end connections. Plus, special Self-Aligning style.New Style Tank Adapters are designed with Spears® patented Special Reinforced (SR) Female Plastic threads for improvedadapter connection strength, even when transitioned to metal pipe (Patent No. 5,582,439). In addition, these Tank Adapters insizes through 4" are designed for use with Nut & Body Spanner Wrench Sets (purchased separately) on the outside connection to aid both installation and in make-up of external threaded connections. Pressure rated to 150 psi @ 73°F (23°C).

Easy Assembly to Tank: 1. Locate and cut designated hole size in tank (see Minimum Hole Size in appropriate chart below). 2. Remove the nut and insert Tank Adapter through hole from inside; leave gasket in place. Note: Body and Gasket must be on installed on the inside of tank (except spigot style in which gasket goes on outside of tank).3. Tighten Nut clockwise while holding body from inside tank or on outside with use of spanner wrench.NOTE: A sound, leak-tight seal can be made on curved surfaces providing the curve on the surface will allow for full and equal 360° pressure contact of the sealing gasket against the tank wall surface (Refer to Minimum Tank Radius below).

NEW STYLE - TANK ADAPTER Socket x Socket Dimensions Also Applicable to 8170E-XXX & 8170V-XXX

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8170-002 1/4 2-1/2 1-13/16 1-1/2 1-1/16 1-3/16 1/2 .10

8170-003 3/8 2-1/2 1-27/32 1-5/8 31/32 7/8 1/2 .11

8170-005 1/2 2-15/16 2-3/16 2-1/16 1-3/16 1-1/8 5/8 .22

8170-007 3/4 2-15/16 2-3/16 2-1/4 1-5/8 15/16 5/8 .26

8170-010 1 3-5/16 2-9/16 2-5/8 2 1-1/16 5/8 .37

8170-012 1-1/4 3-7/16 2-5/8 3-1/8 2-5/16 15/16 5/8 .42

8170-015 1-1/2 3-5/8 2-13/16 3-5/8 2-11/16 13/16 5/8 .98

8170-020 2 4-1/8 3-1/4 4-7/8 3-1/4 1-1/16 3/4 1.28

8170-025 2-1/2 4-27/32 3-7/8 5-1/4 3-9/16 29/32 1 1.79

8170-030 3 5-1/2 4-1/2 6 4-9/16 1-11/16 1 2.62

8170-040 4 5 4 7-1/2 5-1/2 7/16 1-1/4 3.13

8170-080 8 8-5/8 7 12-15/16 10-1/4 1/2 1-1/2 16.02

150 psi @ 73°F

L

M1 M

R

L1 N

Tank Adapter Referenced Dimension Tolerance = ± 1/16"

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (86)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Page 421 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

NEW STYLE - TANK ADAPTER Socket x Fipt Dimensions Also Applicable to 8171E-XXX & 8171V-XXX

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8171-002 1/4 2-1/2 1-13/16 1-1/2 1-1/16 1-1/4 1/2 .10

8171-003 3/8 2-1/2 1-13/16 1-5/8 1-3/16 1-3/16 1/2 .11

8171-005 1/2 2-15/16 2-3/16 2-1/16 1-3/16 1-1/4 5/8 .22

8171-007 3/4 2-15/16 2-15/32 2-1/4 1-5/8 1-3/16 5/8 .25

8171-010 1 3-5/16 2-13/16 2-5/8 1-31/32 1-1/4 5/8 .36

8171-012 1-1/4 3-13/32 2-27/32 3-3/32 2-5/16 1-17/32 5/8 .50

8171-015 1-1/2 3-5/8 2-13/16 3-5/8 2-11/16 1-1/4 5/8 .67

8171-020 2 4-1/8 3-1/4 4-7/8 3-1/4 1-5/8 3/4 1.32

8171-025 2-1/2 4-7/8 7/8 5-1/4 3-13/16 1-13/16 1 1.78

8171-030 3 5-1/2 4-1/2 6 4-9/16 2-3/16 1 2.61

8171-040 4 5 4 7-1/2 5-1/2 1-1/4 1-1/4 3.24

8171-060 6 4-31/32 4-1/16 10-1/16 7-11/16 1/16 1-1/4 5.65

150 psi @ 73°F

N

M

L R

M1

L1

NEW STYLE - TANK ADAPTER Socket x SR Fipt Dimensions Also Applicable to 8171E-XXXSR & 8171V-XXXSR

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8171-002SR 1/4 2-1/2 1-13/16 1-1/2 1-1/16 1-1/4 1/2 .11

8171-003SR 3/8 2-1/2 1-13/16 1-5/8 1-3/16 1-3/16 1/2 .12

8171-005SR 1/2 2-15/16 2-1/4 2-1/16 1-7/32 1-9/32 5/8 .22

8171-007SR 3/4 2-15/16 2-3/16 2-1/4 1-5/8 1-1/4 5/8 .26

8171-010SR 1 3-5/16 2-13/16 2-5/8 1-31/32 1-1/4 5/8 .36

8171-012SR 1-1/4 3-13/32 2-5/8 3-3/32 2-5/16 1-17/32 5/8 .50

8171-015SR 1-1/2 3-5/8 2-13/16 3-5/8 2-11/16 1-1/4 5/8 .70

8171-020SR 2 4-1/8 3-1/4 4-7/8 3-1/4 1-5/8 3/4 1.36

8171-025SR 2-1/2 4-7/8 3-7/8 5-1/4 3-13/16 1-11/16 1 1.90

8171-030SR 3 5-1/2 4-1/2 6 4-9/16 2-3/16 1 2.78

8171-040SR 4 5 4 7-1/2 5-1/2 1-1/4 1-1/4 3.60

8171-060SR 6 4-31/32 4-1/16 10-1/16 7-11/16 1/16 1-1/4 5.74

150 psi @ 73°F

N

M

L

R

M1

L1

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (87)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 422Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

NEW STYLE - TANK ADAPTER Fipt x Fipt Dimensions Also Applicable to 8172E-XXX & 8172V-XXX

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8172-002 1/4 2-1/2 1-13/16 1-1/2 1-1/16 1-5/16 1/2 .10

8172-003 3/8 2-1/2 1-13/16 1-5/8 1-3/16 1-3/8 1/2 .13

8172-005 1/2 2-15/16 2-3/16 2-1/16 1-3/16 1-13/32 5/8 .23

8172-007 3/4 2-15/16 2-15/32 2-1/4 1-5/8 1-1/2 5/8 .25

8172-010 1 3-5/16 2-13/16 2-5/8 1-31/32 1-1/4 5/8 .36

8172-012 1-1/4 3-13/32 2-27/32 3-3/32 2-5/16 1-17/32 5/8 .50

8172-015 1-1/2 3-19/32 3-1/16 3-19/32 2-21/32 1-11/16 5/8 .68

8172-020 2 4-1/8 3-1/4 4-7/8 3-1/4 2-3/16 3/4 1.34

8172-025 2-1/2 4-7/8 3-7/8 5-1/4 3-13/16 2-1/4 1 1.91

8172-030 3 5-1/2 4-1/2 6 4-9/16 2-11/16 1 2.80

8172-040 4 5 4 7-1/2 5-1/2 2 1-1/4 3.53

8172-060 6 5 4-3/16 9-7/8 7-31/32 1-5/32 1-1/4 5.90

150 psi @ 73°F

N L1

M1 M

R L

NEW STYLE - TANK ADAPTER Fipt x SR Fipt Dimensions Also Applicable to 8172E-XXXSR & 8172V-XXXSR

N L1

M1 M

R L

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8172-002SR 1/4 2-1/2 1-7/8 1-9/16 1-1/16 1-5/16 1/2 .12

8172-003SR 3/8 2-1/2 1-13/16 1-5/8 1-3/16 1-3/8 1/2 .14

8172-005SR 1/2 2-15/16 2-3/16 2-1/16 1-7/32 1-13/32 5/8 .24

8172-007SR 3/4 2-15/16 2-15/32 2-1/4 1-5/8 1-3/16 5/8 .26

8172-010SR 1 3-15/16 2-19/32 2-5/8 1-31/32 1-1/4 5/8 .38

8172-012SR 1-1/4 3-13/32 2-27/32 3-3/32 2-5/16 1-17/32 5/8 .50

8172-015SR 1-1/2 3-5/8 2-13/16 3-5/8 2-11/16 1-3/4 5/8 .73

150 psi @ 73°F

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (88)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Page 423 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TANK ADAPTER GASKET SECTION SIZE O.D.* I.D.* T

1/4 1.49 0.99 1/43/8 1.62 1.12 1/41/2 1.98 1.41 1/43/4 2.20 1.57 1/41 2.60 1.90 1/4

1-1/4 3.04 2.23 1/41-1/2 3.54 2.57 1/4

2 4.76 3.15 1/42-1/2 5.13 3.70 1/4

3 5.86 4.39 1/44 7.34 5.31 1/46 9.85 7.95 3/168 12.70 9.94 3/8

* Both outside and inside dimensions are +/- .01 to .03 shore hardness 50-60

New Style Tank Adapter Gasket & Hole Size Requirements

Tank Adapter Size

RecommendedMinimum Hole Size

Minimum InsideCurvature Radius

(inches)

Maximum Tank Wall Thickness (inches)

1/4 1-1/16 2.50 .50

3/8 1-3/16 3.00 .501/2 1-1/2 4.00 .753/4 1-3/4 5.00 .751 2 7.00 .86

1-1/4 2-3/8 9.50 .861-1/2 2-3/4 12.00 .86

2 3-3/8 18.50 1.192-1/2 3-7/8 23.50 1.50

3 4-5/8 32.50 2.004 5-1/2 43.50 1.256 8 79.50 2.068 10-3/8 98.00 4.25

New Style Tank AdaptersOptional Wrench Sets

(Nut & Body Wrench)Part No. TA Size Part No. TA SizeTAW-002 1/4 TAW-012 1-1/4

TAW-003 3/8 TAW-015 1-1/2

TAW-005 1/2 TAW-020 2

TAW-007 3/4 TAW-030 3

TAW-010 1 TAW-040 4

NEW STYLE - TANK ADAPTER Fipt x SR Fipt Dimensions Also Applicable to 8172E-XXXSR & 8172V-XXXSR

N L1

M1 M

R L

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)8172-020SR 2 4-1/8 3-1/4 4-27/32 3-1/32 2-1/8 3/4 1.34

8172-025SR 2-1/2 4-7/8 3-7/8 5-1/4 3-13/16 2-1/4 1 1.97

8172-030SR 3 5-15/32 4-17/32 5-31/32 4-17/32 2-21/32 1 2.87

8172-040SR 4 5 4 7-1/2 5-1/2 2 1-1/4 3.61

150 psi @ 73°F

(continued)

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (89)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 424Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

OLD STYLE - TANK ADAPTER Socket x Fipt Dimensions Also Applicable to 871E-XXX

M M1

LL1R

N

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)

871-005 1/2 2-27/32 2-11/32 2-9/32 1-9/32 1-3/8 5/8 .24

871-007 3/4 2-23/32 2-7/32 2-1/2 1-5/8 29/32 5/8 .30

871-010 1 2-25/32 2-1/8 2-13/16 1-7/8 25/32 21/32 .34

871-012 1-1/4 3-1/8 2-7/16 3-29/32 2-11/32 27/32 5/8 .64

871-015 1-1/2 3-5/32 2-21/32 3-29/32 2-11/32 3/4 5/8 .55

871-020 2 3-3/16 2-17/32 4-31/32 3-15/32 13/16 3/4 1.33

871-030 3 4-19/32 3-13/16 6-7/16 4-15/32 31/32 1-3/16 2.47

871-040 4 4-7/16 3-23/32 7-7/16 5-1/2 1/2 1-1/4 3.17

150 psi @ 73°F

OLD STYLE - TANK ADAPTER Fipt x FiptDimensions Also Applicable to 872E-XXX

Part Number Size L L1 M M1 N R Approx. Wt. (Lbs.)872-005 1/2 2-27/32 2-11/32 2-9/32 1-9/32 1-13/32 5/8 .24

872-007 3/4 2-23/32 2-1/4 2-1/2 1-5/8 1-5/32 5/8 .31

872-010 1 2-25/32 2-5/16 2-13/16 1-7/8 25/32 5/8 .36

872-012 1-1/4 3-1/8 2-5/8 3-27/32 2-11/32 1-1/8 5/8 .67

872-015 1-1/2 3-1/8 2-5/8 3-29/32 2-11/32 1-1/16 5/8 .58

872-020 2 3-5/32 2-3/8 5-1/16 3-7/16 1-5/32 3/4 1.35

872-030 3 4-19/32 3-13/16 6-7/16 4-15/32 1-11/32 1-3/16 2.56

872-040 4 4-7/16 3-1/2 7-1/2 5-1/2 15/16 1-1/4 3.34

150 psi @ 73°F

M M1

L L1 R

N

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (90)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Page 423 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Old Style Tank Adapter Gasket & Hole Size Requirements

Tank Adapter Size

RecommendedMinimum Hole Size

Minimum InsideCurvature Radius

(inches)

Maximum Tank Wall Thickness

(inches)1/2 1-3/8 3.88 1.06

3/4 1-3/4 5.00 1.06

1 2 6.12 1.06

1-1/4 2-7/16 10.75 1.34

1-1/2 2-7/16 10.75 1.34

2 3-9/16 18.50 1.16

3 4-9/16 31.00 1.75

4 5-9/16 42.75 1.81

6 8 79.75 2.06

* Both outside and inside dimensions are +/- .03 shore hardness 65-70

TANK ADAPTER GASKET SECTION SIZE O.D.* I.D.* T

1/2 2.25 1.33 3/16

3/4 2.49 1.69 3/16

1 2.79 1.94 3/16

1-1/4 3.81 2.39 3/16

1-1/2 3.81 2.39 3/16

2 4.89 3.51 3/16

3 6.30 4.49 3/16

4 7.33 5.50 3/16

Self-Aligning Tank AdaptersSwivel Ball design permits straight-pipe connections with up to a 27° angle off vertical pipe centerline in any direction. Aids installation in domed top tanks and provides easy adjustment to compensate for tank curvature in making system connections. The self-aligning tank adapter is not suitable for use on tank sidewalls or tank bottoms. Pressure rated to 75 psi @ 73°F (23°C)

Easy Installation1. Locate and cut designated hole size in tank2. Remove Nut and insert Self-Aligning Tank Adapter through hole from inside. Note: Body and Gasket must be on installed on the inside of tank.3. Tighten Nut (clockwise) while holding body from inside tank.4. Install threaded pipe into ball.5. Position angular offset as desired and tighten lock ring (clockwise) against ball.

Self Aligning Tank Adapter Installation Requirements

Tank Adapter Size Minimum Hole Size Minimum Tank Inside Curvature-Radius (in.) Maximum Tank Wall Thickness

1 3-3/8 18.5 1-5/16

2 4-5/8 32.5 1-5/16

3 5-1/2 43.5 1-11/16

Nut WrenchesWhile not required for installation, Self-Aligning Tank Adapters can use certain nut wrenches produced for use on Spears® regular Tank Adapters (New Style). While designated wrench sizes do not directly correspond, the following chart shows specific regularTank Adapter Nut Wrench to use with each Self-Aligning size. Body wrenches are not currently available.

Self-Aligning Tank Adapter Size

Regular Tank Adapter Nut Wrench to UsePart Number Comment

1” TAW2-020 Regular 2” wrench fits Self-Aligning 1” nut2” TAW2-030 Regular 3” wrench fits Self-Aligning 2” nut3” TAW2-040 Regular 4” wrench Self-Aligning 3” nut

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (91)

Schedule 80 PVC Technical Information

Schedule 80 Tank Adapters

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 424Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

TANK ADAPTER Spigot

Part Number Size A L L1 M Approx. Wt. (Lbs.)8173E-005 1/2 1-3/16 3 1-3/4 1-1/2 .11

8173E-007 3/4 1-1/4 3 2 1-11/16 .14

8173E-010 1 1-3/8 4-1/16 2-3/8 2-3/16 .29

8173E-015 1-1/2 1-5/8 5-1/16 3-1/8 2-7/8 .59

8173E-020 2 1-7/8 5-3/4 3-1/2 3-5/8 .90

75 psi @ 73°F

SELF ALIGNING TANK ADAPTER Fipt Dimensions Also Applicable to 8172ESA-XXX & 8172VSA-XXX

M M1

R L1

L

Part Number Size L L1 M M1 R Approx. Wt. (Lbs.)

8172SA-010 1 2-9/16 1-3/4 4-7/8 3-1/4 3/4 1.11

8172SA-020 2 2-11/16 1-3/4 6 4-9/16 1 1.99

8172SA-030 3 3-1/4 2-1/4 7-1/2 5-1/2 1-1/4 2.61

75 psi @ 73°F

PIPE OD

LL1

M

A

Size A-MAXMinimum Inside

Curvature Radius(inches)

Hole SawSize

1/2 9/16 4-1/2 7/8

3/4 3/4 6 1-1/16

1 1 9-1/2 1-3/8

1-1/2 101/2 16 2

2 1-5/8 26 2-1/2

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (92)

Schedule 80 PVC Technical Information

Hot-Tap Saddles Dimensions & Information

Page 425 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Allows Connection to Existing Pipelines Under Pressure

Dimensions - EPDM Saddle x Socket (Spigot) Zinc Plated BoldsPart Number Size G G1 H H 1 H2 L L1 M

HT2-248 2 x 3/4 (1) 3-9/16 1 6-3/16 2 1-1/2 2-7/16 3-1/2 2HT2-251 2 x 1-1/2 (2) 4-9/16 1-1/4 8-15/16 2-11/16 1-1/2 2-7/16 3-1/2 2-7/8HT2-288 2-1/2 x 3/4 (1) 3-15/16 1 6-9/16 2 1-3/4 4-1/8 4-1/8 2HT2-291 2-1/2 x 1-1/2 (2) 4-13/16 1-1/4 9-3/16 2-11/16 1-3/4 4-1/8 4-1/8 2-7/8HT2-334 3 x 3/4 (1) 4-1/6 1 6-11/16 2 2 3 4-3/4 2HT2-337 3 x 1-1/2 (2) 5-1/4 1-1/4 9-5/8 2-11/16 2 4-1/8 4-3/4 2-7/8HT2-416 4 x 3/4 (1) 4-11/16 1 7-5/16 2 2-5/8 3 5-13/16 2HT2-419 4 x 1-1/2 (2) 5-13/16 1-1/4 10-3/16 2-11/16 2-5/8 4-1/8 5-13/16 2-7/8HT2-524 6 x 3/4 (1) 6 1 8-5/8 2 3-7/8 3 8-1/8 2HT2-527 6 x 1-1/2 (2) 7-1/8 1-1/4 11-1/2 2-11/16 3-7/8 4-1/8 8-1/8 2-7/8HT2-574 8 x 3/4 (1) 7-1/4 1 9-7/8 2 4-7/8 8-1/2 10-1/8 2HT2-577 8 x 1-1/2 (2) 8-9/16 1-1/4 12-9/16 2-11/16 4-7/8 8-1/2 10-1/8 2-7/8

EPDM Saddle x Socket (Spigot) SS316 Bolts, Add The Letter “S” Before The Dash. e.g. Part Number HT2S-248 = 2x3/4 PVC Bolt On Saddle, EPDM O-ring, Stainless Steel Hardware.FKM Saddle x Socket (Spigot) Zinc Plated Bolts, Add The Number “3” Before The Dash. e.g. Part Number HT3-248 = 2x3/4 PVC Bolt On Saddle, FKM O-ring, Zink Plated Hardware.FKM Saddle x Socket (Spigot) SS316 Bolts, Add “3S” Before The Dash. e.g. Part Number HT3S-248 = 2x3/4 PVC Bolt On Saddle, FKM O-ring, Stainless Steel Hardware.EPDM with Stainless Steel Cutter & Bolts, Add “S2S” Before The Dash. e.g. Part Number HTS2S-248 = 2x3/4 PVC Bolt On Saddle, EPDM O-ring, Stainless Steel Cutter & Hardware.FKM with Stainless Steel Cutter & Bolts, Add “S3S” Before The Dash. e.g. Part Number HTS3S-248 = 2x3/4 PVC Bolt On Saddle, FKM O-ring, Stainless Steel Cutter & Hardware.Note: For PVC White, Add The Letter “W” After The Part Number. e.g. Part Number HT2-524W

TECHNICAL DATAMaximum Service TemperaturesPVC 140°FCPVC 200°FNote: Elevated service temperatures require system pressure de-rating.

Not for Distribution of Compressed Air or GasSome leakage is possible during the tapping process, therefore “hot-taps” are not recommended for corrosive or dangerous fl uid medium.

Pressure Rating @ 73°F2" – 4" 235 psi6" 200 psi8" 150 psi

H1G1

G

L1

H

L

H2

M

IPS Spigot O.D.Socket I.D.

• Industrial Grade Bolt-on Saddle with EPDM or FKM O-ring Seals and Choice of Zinc Plated Steel or Type 316 Stainless Steel Hardware.

• Built-in Brass or Stainless Steel Cutter Easily Cuts Hole in PVC, CPVC, HDPE and PP Pipe. Special Design Captures and Retains Coupon from Hole.• Pressure Rated to 235 psi @ 73°F.

• Available to fi t IPS Pipe 2" through 8" with Versatile 3/4" Socket - 1" Spigot Combination Branch Outletor 1"-1/2" Socket - 2" Spigot Combination Branch Outlet

Specially designed tapping saddle allows pipe branch connection topressurized “Hot” lines without system shut-down. Available in PVCWhite, Gray or CPVC Gray confi gurations.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (93)

Schedule 80 PVC Technical Information

Hot-Tap Saddle Installation

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 426Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Basic Installation

STEP 1 Assemble on Pipe

Hot-Tap Saddles are designed for adding branch connections to piping systems under live (“hot”) pressure. Hot-Tap Saddle branch outlets are either 3/4" socket (with 1" Spigot O.D.) or 1-1/2" socket (with 2" Spigot O.D.) in saddle sizes 2" through 8" to t IPS pipe using a built-in O-ring seal. Internal cutter is operated using conventional ratchet and drive extension and permanently retains coupon cut from pipe. Maximum operating pressure at 73°F is 235 psi forsaddle sizes 2" - 4", 200 psi for 6" saddles & 150 psi for 8".

STEP 2 Torque to Speci cations

Allow joint to cure.

STEP 3 Cement Branch Take-off

STEP 4 Remove Cap

STEP 5 Tap to Required Depth

STEP 6 Back-off Cutter to Top to Open Flow

STEP 7 Reinstall Opening Sealed Cap

SEE PRODUCT INSTALLATION INSTRUCTION (HT-3A) FOR DETAILS COMPONENTS

The Hot-Tap Saddle includes the following components:

1. Cap2. Upper O-ring3. Hot-Tap Cutter4. Bolt/Washer5. Saddle Body6. Lower O-ring7. Saddle Bottom8. Nut/Washer

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (94)

Schedule 80 PVC Technical Information

Repair Fittings

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 428Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Schedule 80 Pipe Repair Fittings Allow Difficult Broken Pipe Repair To Be Made Easily

Schedule 80 Repair Fittings

Pipe Extenders, Class 200

Schedule 80 Pipe

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (95)

Schedule 80 PVC Technical InformationCompression Couplings Dimensions & Information

Page 431 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Compression Couplingsw/ EPDM Gasket

Part Number Size (in.) L M N

S110E-05G 1/2 5-3/16 1-13/16 3-3/8

S110E-07G 3/4 5-7/16 2-1/8 3-9/16

S110E-10G 1 5-11/16 2-1/2 3-3/4

S110E-12G 1-1/4 6-1/4 2-15/16 4-1/8

S110E-15G 1-1/2 6-1/2 3-5/16 4-5/8

S110E-20G 2 7-1/8 3-15/16 5-1/16

S110E-25G 2-1/2 8-11/16 4-7/8 5-7/8

S110E-30G 3 9-1/2 5-1/2 6-3/16

S110E-40G 4 11-5/16 6-3/4 7-3/8

PVC Compression CouplingsMulti-Featured Design • Industrial PVC Gray • Easy-Thread

Compression Nut • Converts to Spigot Coupling

• PVC Gray Industrial ConstructionHeavy bodied, chemical and corrosion resistant PVC Gray Industrial units provide for a broad range of applications.

• EPDM Compression GasketsPVC Gray Industrial unit is offered with EPDM gaskets.

• Strong, Buttress Threaded Compression NutsRevised Nut design features increased strength of Buttress thread plus greater ease of Nut installation onto Body. Superior to standard pipe or square-cut ACME type threads.

• Full Service 200 PSI Pressure Rating 200 psi maximum internal pressure rating @ 73°F.

• NSF® Certifi ed for Potable Water UseCompression Couplings with EPDM are certified by NSF International for use in potable water systems.

• Spigot Conversion CapabilityConvert socket-outlet plastic pipe fi tting to compression-outlet fi tting. Simply cut the Compression Coupling in half next to center holding ribs. Body now functions as a spigot for solvent weld attachment to fi tting socket (for Compression Couplings through 2" only).

Excellent for quick connections, system modifi cations and repairs. Spears® redesigned Compression Coupling provides improved function, broaderapplication and increased versatility. PVC Gray Industrial unit providesbroader range of Industrial and Chemical processing applications.Compression nut features strong Buttress threads engineered for easier tightening during installation. New body design has pipe-spigot dimensionsallowing unit to be used to convert a socket fi tting to a compression fi tting.Available in IPS sizes 1/2" through 6".

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (96)

Schedule 80 PVC Technical InformationCompression Couplings Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 432Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Important Installation NoteWARNING: The compression joints provide a positive seal but do not restrain pipe from thrusts and movement underpressure. Use of compression joint requires blocking connecting pipe to prevent any movement. Failure to do so can result in system failure or severe personal injury. Use in cold water/ uid applications only.

Easy InstallationSpears® Compression Couplings easily install by simply sliding nut over pipe, slip on gasket, then insert into body and tighten nuts.

Convert Fittings to Compression OutletSocket type ttings 3/4" through 2-1/2" can be easily converted to compression outlets sizes 1/2” through 2” by simply cutting the Compression Coupling at the center holding ribs and solvent welding the spigot body into a tting socket.

Compression CouplingSize (in.)

Body SpigotSize (in.)

1/2 3/4

3/4 1

1 1-1/4

1-1/4 1-1/2

1-1/2 2

2 2-1/2

2-1/2 3

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (97)

Schedule 80 PVC Technical InformationCompression Couplings Dimensions & Information

Page 433 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

PVC Compression Male Adapters

M

LN T

W

Part No.Size L M N T W

Buna-N EPDMS130-05 S130E-05 1/2 2-11/16 1-13/16 1/4 11/16 1-1/8

S130-07 S130E-07 3/4 2-15/16 2-1/8 5/16 11/16 1-3/8

S130-10 S130E-10 1 3-3/16 2-1/2 5/16 7/8 1-11/16

S130-12 S130E-12 1-1/4 3-3/8 2-15/16 5/16 7/8 2

S130-15 S130E-15 1-1/2 3-9/16 3-5/16 3/8 29/32 2-3/8

S130-20 S130E-20 2 3-7/8 3-15/16 13/32 15/16 3

• Quickly Adapts Pipe to MIPT Thread • Easy-Thread Compression Nut • PVC White with Buna-N or EPDM Gasket • 200 psi Pressure Rating • NSF® Certified for Potable Water Use

Uses same Nut Wrench sets available for Compression Couplings

Compression Male Adapters

Schedule 80 PVC Technical InformationCompression Couplings Dimensions & Information

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (98)

Schedule 80 PVC Technical InformationCompression Couplings Dimensions & Information

GripLoc™ Push-On Coupling

Griploc™ Push-On Couplingw/EPDM O-Ring Seals

Part Number Size L M Approx. Wt. (Lbs.)GL429-005G 1/2 3-13/16 1-5/8 .18GL429-007G 3/4 3-13/16 1-15/16 .19GL429-010G 1 4-1/8 2-1/4 .34GL429-012G 1-1/4 4-3/16 2-5/8 .43GL429-015G 1-1/2 4-1/4 3 .55GL429-020G 2 4-7/16 3-7/16 .69

WARNING: DO NOT INSERT FINGERSWARNING: DO NOT INSERT FINGERS

L

M

GripLoc™ Push-On Coupling Specially designed stainless steel Gripper Ring to firmly grip pipe and prevent potential pull-out. Compressed Gland Ring ensures positive O-ring seal against pipe.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (99)

Schedule 80 PVC Technical InformationFlange Cut-in Repair Kit Installation Instructions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 436Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Spears® Flange Cut-In Kit InstallationWhen planned system changes are needed, system downtime can be a major concern. Spears® Flange Cut-In Kit minimizes downtime for actual cut-in to allow new connection in just minutes. Kit provides all necessary components to create a fl anged joint for connection to system alterations in just minutes. Special Flange Hubcan be cemented to piping and allowed to cure before shutting down and cutting into system. This allows immediate joining to mating fl ange (included) that can also be pre-assembled to desired alteration piping.Kit includes special Split Flange Socket Hub, O-ring Sealed Hub Body, Stainless Steel Clamp, Split Ring,Full-Faced EPDM or FKM Gasket, Mating Flange Hub & Ring, and complete set of Stainless Steel Bolts, FlatWashers and anti-seize Brass Nuts to make the fi nal joint. Available for IPS Pipe Sizes 2" - 12".

Pressure Rated to 150 psi @ 73°F (22°C)Maximum Service Temperature

PVC = 140°F (60°C)CPVC = 200°F (93°C)

Temperature/Pressure De-ratings Apply

DimensionsSize (in.) H L M

2 2-3/8 4-7/8 62-1/2 3-3/4 5-1/2 7

3 4 5-7/8 7-1/24 4-7/8 7-1/8 96 5-7/8 9 118 6-3/4 10-7/8 13-1/210 8-3/8 13-1/2 1612 10 16-3/4 19

LH

M

Split Flange Assembly

Locate and Mark Split Flange position Sand pipe to remove gloss

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (100)

Schedule 80 PVC Technical InformationFlange Cut-in Repair Kit Installation Instructions

Page 437 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Mask Pipe Apply Primer Apply Cement

Primer & Cement Split Flange Position, Press & Hold Split Flange

Install Clamp Torque to 15 ft-lbs

Cut – In & Bevel Pipe at this Distance Minus 1/4” from Glued-on Split Flange

Measure from O-ring Hub FacesMaking The Cut-In

Let assembly cure (recommend over-night) prior to cutting into

piping system.

Shut down and drain system; cut in as described below.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (101)

Schedule 80 PVC Technical InformationFlange Cut-in Repair Kit Installation Instructions

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 438Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Install O-ring Hub; Should Be 1/4” Recess to Pipe

Install Split Ring, Hold in Place with 4- Lubricated Bolts & Washers

Position Elastomer Gasket Insert Remaining Lubricated Bolts & Washers

Install Mating Flange with Washers & Nuts

Evenly Torque to Speci cation on Flange Ring using 180° Opposing Pattern

Mating Flange may be pre-assembled with Elbow, Tee or other con guration as desired

to allow immediate system pressurization after nal assembly to Flanged Cut-In.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (102)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

TECHNICAL INFORMATIONWEIGHTS & DIMENSIONS

THERMOPLASTIC FLANGES MOLDED & FABRICATED

Contact Spears® for any information not found.

Page 439 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (103)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 440Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

GENERAL INFORMATION

Recommendations For Installers And UsersPlastic piping systems should be ENGINEERED, INSTALLED, and OPERATED in accordance with ESTABLISHED DESIGNAND ENGINEERING STANDARDS AND PROCEDURES for plastic piping systems. Suitability for the intended service application should be determined by the installer and /or user prior to installation of a plastic piping system. PRIOR TO ASSEMBLY, allpiping system components should be inspected for damage or irregularities. Mating components should be checked toassure that tolerances and engagements are compatible. Do not use any components that appear irregular or do not fit properly. Contact the appropriate manufacturer of the component product in question to determine usability.

Solvent Weld Connections — Use quality solvent cements and primers formulated for the intended service application, pipe size and type of joint. While the pipe and fitting materials may be compatible with the intended medium, the solvent cement may not be. Consult the manufacturer for suitability of use. Read and follow the cement and primer manufacturers’ applications and cure time instructions thoroughly. Be sure to use the correct size applicator.

Threaded Connections — Use a quality grade thread sealant. WARNING: SOME PIPE JOINT COMPOUNDS OR PTFE PASTESMAY CONTAIN SUBSTANCES THAT COULD CAUSE STRESS CRACKING TO PLASTIC. Spears® Manufacturing Companyrecommends the use of Spears® Blue 75™ thread sealant which has been tested for compatibility with Spears® products. Pleasefollow the sealant manufacturer’s application/installation instructions. Choice of an appropriate thread sealant other than thoselisted above is at the discretion of the installer. 1 to 2 turns beyond FINGER TIGHT is generally all that is required to make asound plastic thread connection. Unnecessary OVERTIGHTENING will cause DAMAGE TO BOTH PIPE AND FITTING.

The information contained in this publication is based on current information and Product design at the time of publication and is subject tochange without notification. Our ongoing commitment to product improvement may result in some variation. No representations, guaranteesor warranties of any kind are made as to its accuracy, suitability for particular applications or results to be obtained therefrom. For verification of technical data or additional information not contained herein, please contact Spears® Technical Services Department [West Coast: (818) 364-1611 — East Coast: (678) 985-1263].

“Lead Free” low lead certification – unless otherwise specified, all Spears® Thermoplastic Flanges specified here-in are certified by NSF International to ANSI/NSF® Standard 61, Annex G and is in compliance with California’s Health & Safety Code Section 116825 (commonly knownas AB1953) and Vermont Act 193. Weighted average lead content <=0.25%.

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (104)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 441 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Bolt TorqueRecommended Bolt Torque is shown in Table 1. Threads should be clean and well lubricated. Actual field conditions may require variations in these recommendations. CAUTION: UNNECESSARY OVER TORQUING WILL DAMAGE THE FLANGE.

Torque SequenceBolt Torque sequence is shown Below in Table 2.

Flange Size (in.) Recommended Torque(ft. lbs.)

1/2 - 1-1/2 122 - 4 25

5 306 - 8 4010 6412 95

14 - 24 110

Table 1

6

18

4

53

72

1

42

311

73

106 2 12

84

95

11511 1 5

913

48

12162610

1437

1 5 91317

48

12162026

1014

183711

15 19

Table 2

Bolt Kit Selection GuideBolt Hardware Kits AvailableFor Connection of 2-Spears® Flanges Includes Bolts, Nuts & Flat Washers for Specified Flange SizeOrder Gaskets & Bolt Kits Separately• Pre-coated, Anti-seize Lubricated Bolts• Available in Zinc Coated Steel, Type 316 Stainless Steel or Type 304 Stainless Steel

FlangeSize

1/2 & 3/41 & 1-1/4

1-1/22

2-1/234

5 & 68

10 & 12

Bolts*Per Kit

444444888

12

Diameter(in.-TPI)1/2 - 131/2 - 131/2 - 135/8 - 115/8 - 115/8 - 115/8 - 113/4 - 103/4 - 107/8 - 9

Length(in.)

22-1/42-1/2

33-1/43-1/23-1/2

44-1/2

5

Kit Part NumberZinc

HK-005HK-010HK-015HK-020HK-025HK-030HK-040HK-060HK-080HK-120

316 SSHK1-005HK1-010HK1-015HK1-020HK1-025HK1-030HK1-040HK1-060HK1-080HK1-120

304 SSHK2-005HK2-010HK2-015HK2-020HK2-025HK2-030HK2-040HK2-060HK2-080HK2-120

* Each Bolt Includes Nut & Two (2) Flat Washers

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (105)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 442Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

GasketsFull faced, 1/8" thick elastomer gaskets with a Shore “A” Durometer of approximately 70 is recommended.

Flange Make-up

Once a flange is joined to pipe, the method for joining two flanges is as follows:

1. Piping runs joined to the flanges must be installed in a straight line position to the flange to avoid stress at the flange due to misalignment. Piping must also be secured and supported to prevent lateral movement which can create stress and damage the flange.

2. With gasket in place, align the bolt holes of the mating flanges by rotating the ring into position.

3. Insert all bolts, washers (two standard flat washers per bolt), and nuts.

4. Make sure the faces of the mating surfaces are flush against gasket prior to bolting down the flanges.

5. Tighten the nuts by hand until they are snug. Establish uniform pressure over the flange face by tightening the bolts in 5 ft.-lbs. increments according to the sequence shown in Table 2 following a 180° opposing sequence.

6. Care must be taken to avoid “bending” the flange when joining a Spears® flange to a “raised face” flange, or a wafer-style valve. Do not use bolts to bring together improperly mated flanges.

Configuration Terminology

Multi-Bolt Pattern Ring — Bolt hole drilling accepts ANSI and Metric FlangesSocket — Slip socket connection for solvent cement weldingSpigot — Pipe O.D. connection for solvent weldingFipt — Female Iron Pipe ThreadSR Fipt — Spears® patented Special Reinforced (SR) plastic threadIPS — Iron Pipe SizePIP — Plastic Irrigation Pipe

FlangeSize1/23/41

1-1/41-1/2

22-1/2

345681012

BoltsPer Kit

444444448888

1212

Gasket Part Number

Buna-NGK1-005GK1-007GK1-010GK1-012GK1-015GK1-020GK1-025GK1-030GK1-040GK1-050GK1-060GK1-080GK1-100GK1-120

EPDMGK2-005GK2-007GK2-010GK2-012GK2-015GK2-020GK2-025GK2-030GK2-040GK2-050GK2-060GK2-080GK2-100GK2-120

FKMGK3-005GK3-007GK3-010GK3-012GK3-015GK3-020GK3-025GK3-030GK3-040GK3-050GK3-060GK3-080GK3-100GK3-120

Gasket Selection GuideFollowing Gasket Numbers Available from Spears®

Order Gaskets & Bolt Kits Separately • 1/8" Full-Face design with ANSI Class 150 Bolt Patterns • Pressure rated to 150 psi @ 73°F • Available in Buna-N, EPDM, or FKM

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (106)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 443 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg

Application

Molded CLASS 150 Flange fittings are coupling devices designed for joining IPS (Iron Pipe Size) plastic piping systems, where frequentdisassembly may be required, and can be used as a transitional fitting for joining plastic to metal piping systems. Suitability of applicationis at the discretion of the user.

Pressure Rating150 psi, water at 73°F.

Flange TypesOne Piece — Available in socket configuration, sizes 1/2" through 8"; threaded and SR threaded (Special Reinforced) configurationsizes 1/2" through 4".Van Stone Style — Two-piece design with rotating flange ring, available in socket configurations, sizes 1/2" through 16"; threadedconfigurations, sizes 1/2" through 4" and spigot configurations, sizes 1/2" through 12".Blind — Closed ring design for capping off a mating flange, flanged fitting or flanged valve, available in sizes 1/2" through 12".

MaterialsAll injection molded flanges are produced from PVC materials approved for potable water use by the National Sanitation Foundation(NSF®).Glass-filled PVC materials may be used in certain Van Stone Style flange rings and large diameter Blind flanges where additionalreinforcement is deemed necessary.

Conformance StandardsSocket & Spigot — ASTM D 2467 (PVC).Threads — ASTM F 1498.Bolt Hole Pattern — ANSI B16.5; ASTM D 4024.Material — ASTM D 1784 (PVC Cell Classification 12454-B).

Weights & DimensionsSpecified minimum bolt lengths are based on the use of two Spears® Flanges, two standard flat washers, standard nut and 1/8" thickelastomer full face gasket. Mating with other brands or accessories may require variation. Bolts and gaskets are not supplied withflanges.

Dimension references:

L = Overall length of hub, ± 1/16 inch. M = Outside diameter of socket hub, ± 1/16 inch. N = (Laying Length) socket/spigot bottom to seal-ring face of flange, ± 1/16 inch. R = Height (thickness) of flange ring, ± 1/16 inch. Max O.D. = Outside diameter of ring, ± 1/16 inch. Bolt Circle Diameter = ANSI B 16.5 Standard; ASTM D 4024, ± 1/16 inch.

Technical Information

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (107)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 444Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange One PieceSocket

M

BOLT CIRCLE DIA. MAX O.D.

L R

N

Part Number Size L M N RBolt

CircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

851-005 1/2 1-1/16 1-9/32 1/8 9/16 2-3/8 4 1/2 2 3-1/2 .22

851-007 3/4 1-3/16 1-1/2 1/8 5/8 2-3/4 4 1/2 2 3-7/8 .31

851-010 1 1-5/16 1-13/16 3/16 3/4 3-1/8 4 1/2 2-1/4 4-1/4 .44

851-012 1-1/4 1-3/8 2-3/16 3/32 21/32 3-1/2 4 1/2 2-1/4 4-5/8 .42

851-015 1-1/2 1-19/32 2-1/2 3/16 23/32 3-7/8 4 1/2 2-1/2 5-1/16 .58

851-020 2 1-27/32 3 5/16 27/32 4-3/4 4 5/8 3 6 .82

851-025 2-1/2 2-1/4 3-1/2 1/2 1 5-1/2 4 5/8 3-1/4 7 1.63

851-030 3 2-5/16 4-9/32 3/8 1-1/16 6 4 5/8 3-1/4 7-1/2 1.74

851-040 4 2-7/16 5-7/32 3/16 1-5/32 7-1/2 8 5/8 3-1/2 9-1/16 2.67

851-050 5 3-1/4 6-3/8 1/4 1 8-1/2 8 3/4 3-3/4 10-1/8 3.00

851-060 6 3-1/4 7-9/16 1/4 1-3/8 9-1/2 8 3/4 4 11 4.06

851-080 8 4-17/32 9-3/4 1/2 1-7/16 11-11/16 8 3/4 4-1/2 13-5/8 7.67

851-100F 10 9-7/8 11-15/16 4-5/8 1-3/8 14-1/4 12 7/8 4 16 16.96

851-120F 12 10-11/16 14-1/8 4-7/16 1-3/8 17 12 7/8 5 19 26.37

Flange One PieceFipt

M

MAX O.D.

LR

N BOLT CIRCLE DIA.

Part Number Size L M N RBolt

CircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

852-005 1/2 1-1/16 1-5/16 9/32 9/16 2-3/8 4 1/2 2 3-1/2 .21

852-007 3/4 1-3/16 1-17/32 15/32 5/8 2-3/4 4 1/2 2 3-7/8 .30

852-010 1 1-5/16 1-13/16 7/16 3/4 3-1/8 4 1/2 2-1/4 4-1/4 .41

852-012 1-1/4 1-3/8 2-7/32 17/32 23/32 3-1/2 4 1/2 2-1/4 4-5/8 .44

852-015 1-1/2 1-11/16 2-1/2 19/32 23/32 3-27/32 4 1/2 2-1/2 5-1/16 .61

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (108)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 445 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange One PieceFipt

M

MAX O.D.

LR

N BOLT CIRCLE DIA.

Part Number Size L M N RBolt

CircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

852-020 2 1-27/32 3 7/8 7/8 4-3/4 4 5/8 3 6 .96

852-025 2-1/2 2-1/4 3-1/2 15/16 1 5-1/2 4 5/8 3-1/4 7 1.65

852-030 3 2-5/16 4-9/32 29/32 1-1/16 6 4 5/8 3-1/4 7-1/2 1.83

852-040 4 2-1/16 5-7/16 5/16 1-1/4 7-1/2 8 5/8 3-1/2 9 2.79

852-050F 5 6-5/8 6-1/8 5-1/4 1-5/16 8-1/2 8 3/4 3-3/4 10-1/8 5.25

852-060F 6 6-15/16 7-1/4 5-1/2 1-5/16 9-1/2 8 3/4 4 11 7.16

852-080F 8 8-9/16 9-7/16 6-15/16 1-7/16 11-3/4 8 3/4 4-1/2 13-1/2 13.41

852-100F 10 7-3/8 11-3/4 5-1/2 1-3/8 14-1/4 12 7/8 5 16 20.65

852-120F 12 7 13-15/16 5 1-3/8 17 12 7/8 4 19 21.79

Special ReinforcedFlange One PieceSR Fipt

M

BOLT CIRCLE DIA.MAX O.D.

LR

N

Part Number Size L M N RBolt

CircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

852-005SR 1/2 1-3/32 1-7/32 11/32 9/16 2-3/8 4 1/2 2 3-1/2 .20852-007SR 3/4 1-3/16 1-3/8 7/16 5/8 2-3/4 4 1/2 2 3-7/8 .27852-010SR 1 1-7/16 1-23/32 17/32 21/32 3-1/8 4 1/2 2-1/4 4-1/4 .37852-012SR 1-1/4 1-9/16 2-1/16 19/32 21/32 3-1/2 4 1/2 2-1/4 4-5/8 .49852-015SR 1-1/2 1-3/4 2-7/16 3/4 3/4 3-7/8 4 1/2 2-1/2 5 .63852-020SR 2 1-13/16 3-1/32 13/16 13/16 4-3/4 4 5/8 3 5-31/32 .99852-025SR 2-1/2 2-1/8 3-19/32 3/8 1 5-1/2 4 5/8 3-1/4 7 1.58852-030SR 3 2-5/16 4-9/32 27/32 1-1/16 6 4 5/8 3-1/4 7-1/2 1.79852-040SR 4 2-1/2 5-1/4 1 1-5/32 7-1/2 8 5/8 3-1/2 9 2.74

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (109)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 446Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

BLIND FLANGE

MAX O.D.BOLT CIRCLE DIA.

R

Part Number Size RBolt

CircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

Max.O.D.

Approx. Wt.(Lbs.)

853-005 1/2 17/32 2-3/8 4 1/2 2 3-17/32 .19853-007 3/4 5/8 2-3/4 4 1/2 2 3-7/8 .28853-010 1 3/4 3-1/8 4 1/2 2-1/4 4-1/4 .41853-012 1-1/4 23/32 3-1/2 4 1/2 2-1/4 4-5/8 .37853-015 1-1/2 23/32 3-27/32 4 1/2 2-1/2 5-1/16 .50853-020 2 27/32 4-3/4 4 5/8 3 5-31/32 .82853-025 2-1/2 1 5-1/2 4 5/8 3-1/4 7 1.61

853-030 3 1-1/16 6 4 5/8 3-1/4 7-1/2 1.63

853-040 4 1-5/32 7-1/2 8 5/8 3-1/2 9-1/16 2.42

853-060 6 1-3/8 9-1/2 8 3/4 4 11 4.36

853-080 8 1-7/16 11-3/4 8 3/4 4-1/2 13-1/2 6.83853-100 10 1-11/16 14-1/4 12 7/8 5 16 11.32853-120 12 1-11/16 17 12 7/8 5 19 15.49

Flange Van Stone Style(Two Piece)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.

(Lbs.)854-005 1/2 1-1/32 1-7/32 5/32 17/32 2-3/8 4 1/2 2 3-1/2 .19

854-007 3/4 1-1/8 1-7/16 5/32 9/16 2-3/4 4 1/2 2 3-7/8 .26

854-010 1 1-9/32 1-3/4 5/32 5/8 3-1/8 4 1/2 2-1/4 4-1/4 .36

854-012 1-1/4 1-13/32 2-5/32 5/32 11/16 3-1/2 4 1/2 2-1/4 4-5/8 .46

854-015 1-1/2 1-17/32 2-7/16 3/16 3/4 3-7/8 4 1/2 2-1/2 5 .56

854-020 2 1-11/16 2-15/16 3/16 13/16 4-3/4 4 5/8 3 6 .85

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (110)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 447 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style(Two Piece)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.

(Lbs.)854-025 2-1/2 2 3-1/2 3/16 31/32 5-1/2 4 5/8 3-1/4 7 1.40

854-030 3 2-1/8 4-1/4 1/4 1-1/16 6 4 5/8 3-1/4 7-1/2 1.66

854-040 4 2-1/2 5-1/4 1/4 1-1/8 7-1/2 8 5/8 3-1/2 9 2.68

854-050 5 3 6-1/4 3/8 1-1/8 8-1/2 8 3/4 3-3/4 10-1/8 3.35

854-060 6 3-3/8 7-9/16 7/16 1-9/32 9-1/2 8 3/4 4 11 4.54

854-080 8 4-3/8 9-5/16 9/32 1-3/8 11-3/4 8 3/4 4-1/2 13-1/2 6.69

854-100 10 5-11/16 11-3/4 21/32 1-5/8 14-1/4 12 7/8 5 16 11.45

854-120 12 7-1/4 13-3/4 5/8 1-1/2 17 12 7/8 5 19 16.78

854-140 14 7-1/2 15-1/2 1/2 2 18-3/4 12 1 5-1/2 21 26.84

854-160 16 8-3/4 17-3/4 3/4 2-3/8 21-1/4 16 1 6-1/2 23-1/2 37.64

854-180 18 9 20 1/4 2-3/8 22-3/4 16 1-1/8 6-1/2 25 45.33

Flange Van Stone Stylewith Plastic Solid Ring(Two Piece)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

S854-020 2 1-11/16 2-15/16 3/16 13/16 4-3/4 4 5/8 3 6 .85

S854-030 3 2-1/8 4-1/4 1/4 1-1/16 6 4 5/8 3-1/4 7-1/2 1.66

S854-040 4 2-1/2 5-1/4 1/4 1-1/8 7-1/2 8 5/8 1/2 9 3.02

S854-060 6 3-3/8 7-9/16 7/16 1-9/32 9-1/2 8 3/4 4 11 4.54

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (111)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 448Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Stylewith Multi-Bolt Pattern Ring(Two Piece)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

Bolt Circle Dia. No. of Bolt

Holes

Bolt Size

MaxO.D.

Approx. Wt. (Lbs.)

Min MaxM854-020 2 1-11/16 2-15/16 3/16 13/16 4-1/2 4-15/16 4 5/8 6 .85

M854-060 6 3-3/8 7-9/16 7/16 1-9/32 9-7/32 9-1/2 8 3/4 11 4.80

M854-080 8 4-3/8 9-5/16 3/8 1-3/8 11-1/2 11-3/4 8 3/4 13-1/2 6.69

Flange Van Stone Stylewith Plastic Solid Ring(Two Piece)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt.(Lbs.)

S854-080 8 4-3/8 9-5/16 3/8 1-3/8 11-3/4 8 3/4 4-1/2 13-1/2 6.69

S854-100 10 5-11/16 11-3/4 11/16 1-5/8 14-1/4 12 7/8 5 16 11.69

S854-120 12 7-1/4 13-3/4 5/8 1-3/4 17 12 7/8 5 19 16.78

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (112)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 449 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style(Two Piece)Fipt

M

BOLT CIRCLE DIA. MAX O.D.

N L

R

Part Number Size L M N R

Bolt Circle Dia.

No. of Bolt

Holes

Bolt Size

Min. Bolt

Length

Max. O.D.

Approx. Wt. (Lbs.)

855-005 1/2 1-1/32 1-7/32 9/32 17/32 2-3/8 4 1/2 2 3-1/2 .19

855-007 3/4 1-5/32 1-3/8 13/32 9/16 2-3/4 4 1/2 2 3-7/8 .27

855-010 1 1-1/4 1-3/4 5/16 5/8 3-1/8 4 1/2 2-1/4 4-1/4 .36855-012 1-1/4 1-3/8 2-1/8 13/32 11/16 3-1/2 4 1/2 2-1/4 4-5/8 .46855-015 1-1/2 1-15/32 2-7/16 13/32 3/4 3-7/8 4 1/2 2-1/2 5 .55855-020 2 1-9/16 2-31/32 1/2 13/16 4-3/4 4 5/8 3 6 .87855-025 2-1/2 2 3-9/16 7/16 1 5-1/2 4 5/8 3-1/4 7 1.22855-030 3 2-1/8 4-1/4 1/2 1-1/16 6 4 5/8 3-1/4 7-1/2 1.73855-040 4 2-1/16 5-1/4 3/8 1-1/4 7-1/2 8 5/8 3-1/2 9 2.61

855-060F 6 6-3/8 7-3/16 4-15/16 1-1/4 9-1/2 8 3/4 4 11 7.62855-080F 8 8-1/8 9-5/16 6-7/16 1-1/2 11-3/4 8 3/4 4-1/2 13-1/2 12.84855-100F 10 10-3/8 11-9/16 8-9/16 1-11/16 14-1/4 12 7/8 5 16 20.65855-120F 12 11-13/16 13-3/4 9-3/4 1-5/8 17 12 7/8 5 19 33.52

Flange Van Stone Style(Two Piece)Spigot

PIPE O.D.

BOLT CIRCLE DIA. R

N L

MAX O.D.

Part Number Size L N R

Bolt Circle Dia.

No. of Bolt

Holes

Bolt Size

Min. Bolt Length

Max. O.D.

Approx. Wt. (Lbs.)

856-005 1/2 1-3/4 29/32 17/32 2-3/8 4 1/2 2 3-1/2 .20

856-007 3/4 1-15/16 31/32 9/16 2-3/4 4 1/2 2 3-7/8 .29

856-010 1 2-3/16 1-1/32 5/8 3-1/8 4 1/2 2-1/4 4-1/4 .39

856-012 1-1/4 2-11/32 1-3/32 11/16 3-1/2 4 1/2 2-1/4 4-5/8 .50

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (113)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 450Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style(Two Piece)Spigot

PIPE O.D.

BOLT CIRCLE DIA. R

N L

MAX O.D.

Part Number Size L N R

Bolt Circle Dia.

No. of Bolt

Holes

Bolt Size

Min. Bolt Length

Max. O.D.

Approx. Wt. (Lbs.)

856-015 1-1/2 2-5/8 1-9/32 3/4 3-7/8 4 1/2 2-1/2 5 .60

856-020 2 2-7/8 1-11/32 13/16 4-3/4 4 5/8 3 6 .94

856-025 2-1/2 3-1/16 1-9/32 1 5-1/2 4 5/8 3-1/4 7 1.29

856-030 3 3-3/8 1-7/16 1-1/16 6 4 5/8 3-1/4 7-1/2 1.82

856-040 4 3-7/8 1-5/8 1-1/4 7-1/2 8 5/8 3-1/2 9 2.93

856-060 6 4-3/4 1-25/32 1-9/32 9-1/2 8 3/4 4 11 4.62

856-080 8 5-7/8 1-15/16 1-3/8 11-3/4 8 3/4 4-1/2 13-1/2 7.95

856-100 10 8 2-1/4 1-5/8 14-1/4 12 7/8 5 16 15.61

856-120 12 8-1/2 2-3/16 1-5/8 17 12 7/8 5 19 21.31

Flange Van Stone Stylewith Multi-Bolt Pattern Ring(Two Piece)Spigot

PIPE O.D.

BOLT CIRCLE DIA.MAX O.D.

R

NL

Part Num-ber Size L N R

Bolt Circle Dia. No. of Bolt

Holes

Bolt Size

Max. O.D.

Approx. Wt. (Lbs.)

Min. Max.M856-020 2 2-7/8 1-11/32 13/16 4-1/2 4-15/16 4 5/8 6 .94

M856-060 6 4-3/4 1-25/32 1-9/32 9-7/32 9-1/2 8 3/4 11 4.77

M856-080 8 5-7/8 1-15/16 1-3/8 11-1/2 11-3/4 8 3/4 13-1/2 7.95

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (114)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 451 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Technical Information

ApplicationFabricated IPS and PIP Flange fittings are coupling devices designed for joining IPS (Iron Pipe Size) or PIP (Plastic Irrigation Pipe) plastic piping systems, where frequent disassembly may be required. These flanges can be used as transitional fittings for joining IPS-to-IPS, PIP-to-PIP, IPS-to-PIP, or plastic to metal piping systems. Suitability of application is at the discretion of the user.

Pressure RatingAll standard fabricated flanges are Van Stone Style (except blind flange) — two piece design with rotating flange ring.

Class 150 IPS Flanges (with steel ring): 150 psi, water at 73°F.

IPS Flanges 18" - 24" (with plastic ring): 50 psi, water at 73°F.

IPS Flanges, Class 300 Bolt Pattern (with plastic ring): 1/2" - 16" 150 psi, 18" - 24" 50 psi, water at 73°F.

Blind Flanges, 14" - 24": 50 psi, water at 73°F.

PIP Flanges, 6" - 16" (with plastic ring & molded IPS flanges w/PIP Adapters): 125 psi, water at 73°F

PIP Flanges, 18" - 24" (with steel ring): 125 psi, water at 73°F

Flange TypesVan Stone Style Class 150 IPS (with steel ring) — Fabricated PVC body with steel flange ring, available in sizes 18" through 24",slip socket and 14" through 24", spigot.

Van Stone Style IPS (with plastic ring) — Fabricated PVC body with PVC flange ring, available in sizes 18" through 24", slip socket and 14" through 24", spigot.

Van Stone Style PIP (with plastic ring) — PIP adapter fabricated to injection molded PVC Van Stone Style IPS flange, available in sizes 6" through 16", slip socket.

Van Stone Style PIP (with steel ring) — Fabricated PVC body with steel flange ring, available in sizes 14" through 24", slip socket.

Blind — Closed ring design for capping off a mating flange; fabricated PVC available in sizes 5" and 14" through 24".

Special Note On PIP Flange SizesIn order to facilitate connections between IPS and PIP systems, all Plastic Irrigation Pipe flanges are fabricated with PIP sockets using standard IPS Flange Rings. These are indicated in dimension tables under “Size” as (nominal IPS flange size) x (actual PIP O.D.), such as: 6" x 6.140".

To better meet user needs, Spears® offers flanges for 15.300" O.D. PIP with either 14" or 16" IPS Flange Rings. In addition, both 18.360" and 18.701" O.D. PIP are offered with 18" IPS Flange Rings.

MaterialsAll fabricated flanges are produced from PVC materials approved for potable water use by the National Sanitation Foundation (NSF®).

Steel flange rings are carbon steel.

Conformance Standards

Materials — ASTM D 1784 (PVC Cell Classification 12454-B).

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (115)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 452Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style PIP(with Plastic Ring)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

354-060F 6x6.140 4-1/16 7-9/16 11/16 1-1/4 9-1/2 8 3/4 4 11-1/2 5.53354-080F 8x8.160 4-15/16 9-3/8 9/16 1-1/2 11-3/4 8 3/4 4-1/2 13-5/8 8.30354-100F 10x10.200 6-1/4 11-3/4 1 1-5/8 14-1/4 12 7/8 5 16 14.49354-120F 12x12.240 7-5/16 13-13/16 1-1/16 1-5/8 17 12 7/8 5 19 21.59354-151F 16x15.300 8-11/16 17-3/4 11/16 2-3/8 21-1/4 16 1 6-1/2 23-1/2 66.06

Flange Van Stone Style PIP(with Plastic Ring)Socket

M

BOLT CIRCLE DIA.MAX O.D.

R

L

N

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

354-150F 14x15.300 19-5/16 16-3/16 10-5/16 2 18-3/4 12 1 5-1/2 21 47.29

Dimension references:L = Overall length of hub, ± 1/2 inch.M = Outside diameter of socket hub, ± 1/4 inch.N = (Laying Length) socket bottom to seal-ring face of

flange, ± 1/2 inch.R = Height (thickness) of flange ring, ± 1/16 inch.

Max O.D = Outside diameter of ring, ± 1/16 inch.Bolt Circle Diameter = ANSI B16.5 Standard; ASTM D 4024, ± 1/16 inch.

Specified minimum bolt lengths are based on the use of two Spears® Flanges, two standard flat washers, standard nut and 1/8” thickelastomer full face gasket. Mating with other brands or accessories may require variations. Note: Bolts and gaskets are not supplied with flanges.

Weights & Dimensions

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (116)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 453 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style PIP(with Steel Ring)Socket

N

M

BOLT CIRCLE DIA. MAX O.D.

R L

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

354-181F 18x18.701 15-1/8 19-13/16 6-1/8 1/2 22-3/4 16 1-1/8 3 25 53.80

354-182F 18x18.360 11-5/8 19-1/2 5-5/8 1/2 22-3/4 16 1-1/8 3 25 53.80

354-200F 20x20.400 11-3/8 21-9/16 5-3/8 1/2 25 20 1-1/8 3 27-1/2 63.06

354-201F 20x22.047 16-9/16 23-1/4 6-9/16 1/2 25 20 1-1/8 3 27-1/2 64.43

354-241F 24x24.803 19-7/8 26-3/16 7-7/8 1/2 29-1/2 20 1-1/4 3 32 90.50

Blind Flange

MAX O.D. BOLT CIRCLE DIA.

R

PartNumber Size R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

Max.O.D.

Approx. Wt.(Lbs.)

853-050F 5 1 8-1/2 8 3/4 4-1/8 10-1/16 3.63

853-140F 14 1-1/2 18-3/4 12 1 4-1/8 21 27.50

853-160F 16 1-1/2 21-1/4 16 1 4-1/8 23-1/2 33.83

853-180F 18 1-1/2 22-3/4 16 1-1/8 4-1/8 25 39.52

853-200F 20 1-1/2 25 20 1-1/8 4-1/8 27-1/2 47.67

853-240F 24 1-1/2 29-1/2 20 1-1/4 5-1/2 32 61.96

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (117)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 454Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style IPS(with Plastic Ring)Socket

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

PartNumber Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

854-180FP 18 15 19-1/8 6 1-1/2 22-3/4 16 1-1/8 4-1/8 25 36.09

854-200FP 20 16 21-3/16 6 1-1/2 25 20 1-1/8 5-1/2 27-1/2 55.09

854-240FP 24 19 25-3/8 7 1-1/2 29-1/2 20 1-1/4 5-1/2 32 80.93

Flange Van Stone Style IPS(with Steel Ring)Socket

N

M

BOLT CIRCLE DIA. MAX O.D.

R L

PartNumber Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

854-120FS 12 9-5/8 13-9/16 3-3/8 1/2 17 12 7/8 3 19 ---

854-140FS 14 11 14-7/8 4 1/2 18-3/4 12 1 3 21 ---

854-160FS 16 13-1/2 17 5-1/2 1/2 21-1/4 16 1 3 23-1/2 ---

854-180FS 18 14 19-1/8 5 1/2 22-3/4 16 1-1/8 3 25 49.30

854-200FS 20 15 21-3/16 5 1/2 25 20 1-1/8 3 27-9/16 65.00

854-240FS 24 18 25-3/8 6 1/2 29-1/2 20 1-1/4 3 32 86.15

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (118)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Page 455 Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears® Manufacturing CompanyDue to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style Class 300(with Plastic Ring)Socket

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

854-005CL300 1/2 1 1-3/16 3/16 1/2 2-5/8 4 1/2 2 3-3/4

854-007CL300 3/4 1-1/8 1-3/8 3/16 1 3-1/4 4 5/8 3-1/2 4-5/8

854-010CL300 1 1-1/4 1-3/4 3/16 1 3-1/2 4 5/8 3-1/2 4-7/8

854-012CL300 1-1/4 1-3/8 2-1/8 1/8 1 3-7/8 4 5/8 3-1/2 5-1/4

854-015CL300 1-1/2 1-1/2 2-7/16 3/16 1 4-1/2 4 5/8 3-1/2 6-1/8

854-020CL300 2 1-11/16 2-15/16 3/16 1 5 8 5/8 3-1/2 6-1/2

854-025CL300 2-1/2 2 3-9/16 1/4 1 5-7/8 8 3/4 3-1/2 7-1/2

854-030CL300 3 2-1/8 4-1/4 1/4 1 6-5/8 8 3/4 3-1/2 8-1/4

854-040CL300 4 2-1/2 5-1/4 1/4 1-1/2 7-7/8 8 3/4 4-1/2 10

854-060CL300 6 3-7/16 7-9/16 3/8 1-1/2 10-5/8 12 3/4 4-1/2 12-1/2

854-080CL300 8 4-3/8 9-3/8 5/16 1-1/2 13 12 7/8 4-1/2 15

854-100CL300 10 5-11/16 11-3/4 5/8 1-1/2 15-1/4 16 1 4-1/2 17-1/2

854-120CL300 12 7-5/16 13-13/16 9/16 1-1/2 17-3/4 16 1-1/8 4-1/2 20-1/2

854-140CL300 14 7-9/16 15-9/16 9/16 2 20-1/4 20 1-1/8 5-1/2 23

854-160CL300 16 8-9/16 17-3/4 9/16 2 22-1/2 20 1-1/4 6 25-1/2

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Flange Van Stone Style Class 300(with Plastic Ring)Socket

Part Number Size L M N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

854-180CL300 18 15 19-1/8 6 2 24-3/4 24 1-1/4 6 28 61.11

854-200CL300 20 15-1/4 21-3/16 5-1/4 2 27 24 1-1/4 6 30-1/2 68.38

854-240CL300 24 19 25-3/8 7 2 32 24 1-1/2 6 36 134.51

M

BOLT CIRCLE DIA. MAX O.D.

R

N

L

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (119)

Schedule 80 PVC Technical Information

PVC Pipe Flange Dimensions & Information

Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 456Due to Material Cost Variations, Prices Subject to Change. Check On-line Catalog @ www.spearsmfg.com

Flange Van Stone Style IPS(with Plastic Ring)Spigot

IPS PIPE O.D.

BOLT CIRCLE DIA. MAX O.D.

R N

L

PartNumber Size L N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

856-140FP 14 15-5/16 7-3/4 2 18-3/4 12 1 5-1/2 21 24.00856-160FP 16 17-13/16 8-9/16 2-3/8 21-1/4 16 1 6-1/2 23-1/2 61.83856-180FP 18 19-9/16 9-9/16 2-3/8 22-3/4 16 1-1/8 6-1/2 25 34.81856-200FP 20 13 2-1/16 1-1/2 25 20 1-1/8 5-1/2 27-1/2 42.50856-240FP 24 16- 3/8 2-1/8 1-1/2 29-1/2 20 1-1/4 5-1/2 32 68.00

Flange Van Stone Style IPS(with Steel Ring)Spigot

IPS PIPE O.D.

BOLT CIRCLE DIA. MAX O.D.

R N

L

PartNumber Size L N R

BoltCircleDia.

No. ofBolt

Holes

BoltSize

Min.Bolt

Length

MaxO.D.

Approx. Wt. (Lbs.)

856-140FS 14 10 15/16 1/2 18-3/4 12 1 3 21 36.63856-160FS 16 11 1 1/2 21-1/4 16 1 3 23-1/2 46.50856-180FS 18 12 1-1/16 1/2 22-3/4 16 1-1/8 3 25 47.27856-200FS 20 13 1-1/16 1/2 25 20 1-1/8 3 27-1/2 59.00856-240FS 24 15-3/8 1-1/8 1/2 29-1/2 20 1-1/4 3 32 84.00

Schedule 80 PVC Technical Information Schedule 80 PVC &middot; PDF fileSchedule 80 PVC Technical Information Schedule 80 PVC Pipe Dimensions & Pressure Ratings Made in the U.S.A. Suitable - [PDF Document] (2024)

FAQs

What does Schedule 80 PVC pipe mean? ›

A pipe's schedule refers to its relative thickness. Schedule 80 PVC pipe has thicker walls than schedule 40 PVC pipe. Therefore, it can handle higher pressure applications. Schedule 40 PVC is usually white in color and is used for irrigation, water handling and other relatively low pressure jobs.

What is the ASTM for Schedule 80 PVC pipe? ›

PVC Schedule 80 pipe shall be Iron Pipe Size (IPS) conforming to ASTM D 1785. Injection molded PVC Schedule 80 fittings shall conform to ASTM D 2467. PVC Schedule 80 threaded fittings shall conform to ASTM D 2464. Pipe and fittings shall be manufactured as a system and be the product of one manufacturer.

What is schedule 80 PVC pipe rated for pressure? ›

Spears® recommends that only Schedule 80 or heavier wall thickness pipe should be threaded. EX: 2" PVC SCHEDULE 80 @ 120°F = 400 psi x 0.40 = 160 psi max.

What is the difference between Schedule 80 CPVC and Schedule 80 PVC? ›

Schedule 80 refers to the thickness of the pipe, and CPVC refers to the chemical makeup of the pipe. Therefore, schedule 80 CPVC is able to tolerate the PSI levels of schedule 80 PVC, which vary depending on the size of the pipe, while handling the temperatures of CPVC (200⁰ F).

Is schedule 80 PVC ok for drinking water? ›

Westlake Pipe & Fittings Schedule 40, Schedule 80 and insert fittings are listed with the National Sanitation Foundation (NSF) for use in potable water applications and comply with Standard 14 and 61.

Where is schedule 80 PVC required? ›

The only time schedule 80 PVC conduit would be required is when the service cable is exposed to physical damage. The AHJ needs to determine if the cables are exposed to physical damage since there is not a definition of physical damage in the code.

How do I know if my PVC pipe is Schedule 40 or 80? ›

Schedule 40 PVC is usually white in color and has thinner walls, thus can handle less pressure than it's counterpart. Schedule 40 PVC pipe works best for low water pressure applications. By contrast, Schedule 80 PVC is usually gray in color and has thicker walls; therefore, it can handle higher water pressures.

Is Schedule 80 PVC considered rigid conduit? ›

Listed for use in above ground and below ground applications that are subject to physical damage.

Is Schedule 80 PVC fire rated? ›

UL 94V-0 FIRE RATING.

No flaming once cut off the fire source means the greatest fire rating in the industry.

What is the strongest PVC pipe? ›

Both schedule 40 and 80 PVC are used widely around the world. Each one has its benefits in different applications. Schedule 40 pipe has thinner walls, so it is best for applications involving relatively low water pressure. Schedule 80 pipe has thicker walls and is able to withstand higher PSI (pounds per square inch).

What type of PVC is used for plumbing? ›

PVC-U is the most common PVC type for pipes and fittings including transportation of drinking water, soil and waste, sewage and underground drainage and industrial applications. Pipes and fittings made of PVC-U have many benefits.

Can Schedule 80 PVC be used above ground? ›

According to the NEC, both Schedule 40 and Schedule 80 conduit are suitable for above ground usage where they may be exposed to sunlight and weather. However, only the thicker Schedule 80 is suitable for above-ground usage where it may be exposed to excessive physical damage.

Why is CPVC not used anymore? ›

Even a small leak will destroy the piping system causing the CPVC pipes and fittings to turn brittle and fail. Once contaminated, the entire piping system must be replaced. Because of the significant risk of contamination we do not recommend the use of CPVC (or PVC) piping in the hydronic piping application.

Can you use CPVC glue on Schedule 80 PVC? ›

PVC glue isn't aggressive enough to adhere to CPVC, so you can never use PVC glue with CPVC pipe. You can, however, use CPVC glue or cement with PVC fittings because it's aggressive enough for CPVC but not too much that it breaks down PVC.

How to tell if a pipe is PVC or CPVC? ›

CPVC and PVC Visual Similarities and Differences
  1. PVC pipes are white or dark gray in color.
  2. CPVC is off-white, light gray, or yellow in color.
  3. Both pipe types have technical specifications printed on the side for easy verification.
  4. Both pipe types are available in plain end and bell end.

Which is stronger, schedule 40 or 80 PVC? ›

Each one has its benefits in different applications. Schedule 40 pipe has thinner walls, so it is best for applications involving relatively low water pressure. Schedule 80 pipe has thicker walls and is able to withstand higher PSI (pounds per square inch). This makes it ideal for industrial and chemical applications.

Can Schedule 40 PVC fittings be used on Schedule 80 PVC? ›

Due to the thicker walls, schedule 80 PVC is not only able to handle higher PSI, it is also more resistant to bending and breaking than schedule 40 PVC. Because schedule 40 PVC and schedule 80 PVC pipe have the same outer diameter, you can use schedule 40 PVC fittings with schedule 80 PVC pipe and vice versa.

Should I use schedule 40 or 80 conduit? ›

Schedule 40 PVC conduit is permitted for exposed locations where not subject to physical damage. Schedule 80 PVC conduit is identified for use in areas subject to physical damage.

Can Schedule 80 PVC be glued to CPVC? ›

PVC glue isn't aggressive enough to adhere to CPVC, so you can never use PVC glue with CPVC pipe. You can, however, use CPVC glue or cement with PVC fittings because it's aggressive enough for CPVC but not too much that it breaks down PVC.

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Reed Wilderman

Last Updated:

Views: 5740

Rating: 4.1 / 5 (72 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Reed Wilderman

Birthday: 1992-06-14

Address: 998 Estell Village, Lake Oscarberg, SD 48713-6877

Phone: +21813267449721

Job: Technology Engineer

Hobby: Swimming, Do it yourself, Beekeeping, Lapidary, Cosplaying, Hiking, Graffiti

Introduction: My name is Reed Wilderman, I am a faithful, bright, lucky, adventurous, lively, rich, vast person who loves writing and wants to share my knowledge and understanding with you.